Whirlpool WRT541SZDM Use & Care Guide - Page 8

Contour Door Models Only, Final Steps - parts

Get Whirlpool WRT541SZDM PDF manuals and user guides View all Whirlpool WRT541SZDM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Assemble the parts for the top hinge as shown. See Top Hinge graphic. Do not tighten screws completely. Contour Door Models Only: ■ Remove the screw attaching the hinge pin to the hinge. Turn the hinge over so that it is pointing in the opposite direction. ■ Place the plastic spacer beneath the hinge so that it will be between the hinge and the cabinet, making sure the holes are aligned. B B Final Steps 1. Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover. See Top Hinge graphic. WARNING A C C A A. Plastic spacer B. Hinge pin screw C. Hinge pin ■ Fasten the top hinge to the opposite side of the cabinet, inserting the screws only halfway, so you will be able to replace and align the freezer door later. 5. Line up the doors so that the bottom of the freezer door aligns evenly with the top of the refrigerator door. Tighten all screws. NOTE: The distance between the doors should be approximately 16 mm). Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 2. Remove the cover from the base grille. Move the cover to the opposite side. 3. Align the clips on the base grille with the screws on the bottom of the cabinet. Push the base grille toward the cabinet until it is flush. 4. Plug into a grounded 3 prong outlet. 5. Reset the controls. See "Using the Control(s)." 6. Return all removable door parts to doors and food to refrigerator. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
8
4.
Assemble the parts for the top hinge as shown. See Top Hinge
graphic. Do not tighten screws completely.
Contour Door Models Only:
■
Remove the screw attaching the hinge pin to the hinge.
Turn the hinge over so that it is pointing in the opposite
direction.
■
Place the plastic spacer beneath the hinge so that it will
be between the hinge and the cabinet, making sure the
holes are aligned.
■
Fasten the top hinge to the opposite side of the cabinet,
inserting the screws only halfway, so you will be able to
replace and align the freezer door later.
5.
Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.
NOTE:
The distance between the doors should be
approximately
⁵⁄₈
" (16 mm).
Final Steps
1.
Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover. See Top Hinge graphic.
2.
Remove the cover from the base grille. Move the cover to the
opposite side.
3.
Align the clips on the base grille with the screws on the
bottom of the cabinet. Push the base grille toward the
cabinet
until it is flush.
4.
Plug into a grounded 3 prong outlet.
5.
Reset the controls. See “Using the Control(s).”
6.
Return all removable door parts to doors and food to
refrigerator.
A. Plastic spacer
B. Hinge pin screw
C. Hinge pin
A
C
C
A
B
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING