Whirlpool WRT771REYB Use & Care Guide - Page 5

Refrigerator Doors

Get Whirlpool WRT771REYB PDF manuals and user guides View all Whirlpool WRT771REYB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten. Complete the Installation WARNING AB C D EFG A. Refrigerator water tubing B. Nut (provided) C. Bulb D. Coupling (provided) E. Ferrule (purchased) F. Nut (purchased) G. Household water line 4. Turn shutoff valve ON. 5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak. Style 3 1. Unplug refrigerator or disconnect power. 2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator. 3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten. A B A. Bulb B. Nut (provided) 4. Turn shutoff valve ON. 5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Plug into a grounded 3 prong outlet. 2. Flush the water system. See "Water Dispenser." NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container. Refrigerator Doors TOOLS NEEDED hex head socket wrench, Torx®† T27 screwdriver, #2 Phillips screwdriver, flat-blade screwdriver open-end wrench, flat 2" putty knife. IMPORTANT: ■ Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors. ■ Depending on your model, you have either Style 1 - interior controls and water dispenser or Style 2 - exterior controls and water dispenser. Follow the instructions and graphics specific to your model. ■ All graphics referenced in the following instructions are included later in this section after "Final Steps." Style 1 - Remove Doors and Hinges Hex Head Hinge Screw 12-24 Torx®† Head Screw 1. Unplug refrigerator or disconnect power. 2. Open the refrigerator door and remove the base grille from the bottom front of the refrigerator. See Base Grille graphic. †®TORX is a registered trademark of Saturn Fasteners, Inc. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
5
NOTE:
Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4.
Turn shutoff valve ON.
5.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 3
1.
Unplug refrigerator or disconnect power.
2.
Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3.
Thread the provided nut onto the water valve as shown.
NOTE:
Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4.
Turn shutoff valve ON.
5.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
1.
Plug into a grounded 3 prong outlet.
2.
Flush the water system. See “Water Dispenser.”
NOTE:
Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Refrigerator Doors
TOOLS NEEDED:
⁵⁄₁₆
" hex head socket wrench, Torx
®†
T27
screwdriver, #2 Phillips screwdriver, flat-blade screwdriver,
⁵⁄₁₆
"
open-end wrench, flat 2" putty knife.
IMPORTANT:
■
Before you begin, turn the refrigerator control OFF, unplug
refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors.
■
Depending on your model, you have either
Style 1
- interior
controls and water dispenser or
Style 2
- exterior controls and
water dispenser. Follow the instructions and graphics specific
to your model.
■
All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
Style 1 - Remove Doors and Hinges
⁵⁄₁₆
" Hex Head Hinge Screw
12-24 Torx
®†
Head Screw
1.
Unplug refrigerator or disconnect power.
2.
Open the refrigerator door and remove the base grille from the
bottom front of the refrigerator. See Base Grille graphic.
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (provided)
E. Ferrule (purchased)
F. Nut (purchased)
G.Household water line
A. Bulb
B. Nut (provided)
A
B
C
D
E
F
G
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
†®TORX is a registered trademark of Saturn Fasteners, Inc.