Whirlpool WTW2000HW Owners Manual - Page 4
Location Requirements - manual
View all Whirlpool WTW2000HW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
Alternate Parts Your installation may require additional parts. For information on ordering, please refer to the back cover of this manual. If You Have: You Will Need to Buy: Laundry tub or standpipe taller than 72" (183 cm) Sump pump system (if not already available) 1" (2.5 cm) diameter standpipe 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter, Part Number 3363920 Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump, and connectors (available from local plumbing suppliers) Floor drain Siphon break, Part Number 285320; additional drain hose, Part Number 3357090 and connector kit, Part Number 285442 Water faucets beyond reach of fill hoses 2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008 Drain hose too short Drain hose, Part Number 388423 and hose kit, Part Number 285442 Drain hose that is too long Hose kit, Part Number 285442 Lint clogged drain Drain protector, Part Number 367031 Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk." Your washer can be installed in a basement, laundry room, closet, or recessed area. See "Drain System." Washer Dimensions 21" (533 mm) 23" (584 mm) You will need: ■■ A water heater set to deliver 120°F (49°C) water to the washer. ■■ A grounded electrical outlet located within 5 ft (1.5 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." ■■ Hot and cold water faucets located within 3½ ft (1.1 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-690 kPa). ■■ A level floor with a maximum slope of ¾" (1.9 cm) under entire washer. Installing the washer on carpeting is not recommended. ■■ A sturdy floor to support the washer weight (washer, water, and load) of 225 lbs (102 kg). Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for winterizing information. Recessed area or closet installation The dimensions shown are for the recommended spacing allowed, except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings are the minimum required. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances may be required for wall, door, and floor moldings. ■■ Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer. ■■ If a closet door is installed, the minimum air openings in the top and bottom of the door are required. Louvered doors with air openings in the top and bottom are acceptable. ■■ Companion appliance spacing should also be considered. Washer Only 3" (76 mm) 12" (305 mm) 48 in.2 (310 cm2) 37" (940 mm) 3/4" (19 mm)* *Minimum measurement with leveling feet installed. IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Proper installation is your responsibility. 4" (102 mm) 1" (25 mm) 1" (25 mm) 24 in.2 (155 cm2) 1" (25 mm) 3" (76 mm) Recessed area Closet door with vents 4