Whirlpool WVW75UC0DS Use & Care Guide - Page 4
Installation Requirements - recirculating kit
View all Whirlpool WVW75UC0DS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed ■ Level ■ Drill with 1¼" (3.2 cm 3.2 mm), and 7.9 mm) drill bits ■ Pencil ■ Wire stripper or utility knife ■ Tape measure or ruler ■ Pliers ■ Caulking gun and weatherproof caulking compound ■ Vent clamps ■ Jigsaw or keyhole saw ■ Flat-blade screwdriver ■ Metal snips ■ Phillips screwdriver Parts needed ■ Home power supply cable ■ ½" (12.7 mm) UL listed or CSA approved strain relief ■ 3 UL listed wire connectors For vented installations, you will also need: ■ 1 wall or roof cap ■ Metal vent system For non-vented (recirculating) installations, you will also need: ■ Recirculation Kit Part Number W10294733 for non-vented (recirculating) installations only. See "Assistance or Service" section to order. ■ 6" (15.2 cm) diameter round metal vent duct - length required is determined by ceiling height. Parts supplied Remove parts from packages. Check that all parts are included. ■ Hood canopy assembly with blower, LED lights and canopy glass already installed. ■ Vent transition with back draft dampers installed ■ Metal grease filter ■ Vent cover support bracket ■ Mounting template ■ 2-piece vent cover ■ Air deflector (for non-vented [recirculating] installations only) ■ 4 - 4.2 x 8 screws ■ 6 - 5 x 45 mm mounting screws ■ 2 - 3.5 x 9.5 mm mounting screws ■ 2 - 8 x 40 mm wall anchors ■ 4 - 10 x 50 mm wall anchors ■ T10 Torx®† adapter ■ T20®† Torx® adapter †®TORX, T10 and T20 are registered trademarks of Acument Intellectual Properties, LLC. 4 Location Requirements IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood. Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. This range hood is recommended for use with cooktops with a maximum total rating of 60,000 BTUs or less. Grounded electrical outlet is required. See "Electrical Requirements" section. The canopy hood is factory set for venting through the roof or wall. For non-vented (recirculating) installation see "For nonvented (recirculating) installation only" in the "Connect Vent System" section. Recirculation Kit Part Number W10294733 is available from your dealer or an authorized parts distributor. All openings in ceiling and wall where canopy hood will be installed must be sealed. For Mobile Home Installations The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes. Product Dimensions 10⁷⁄₈" (27.6 cm) 13 33.5 cm) 20" (50.8 cm) 30" (76.2 cm) or 36" (91.4 cm)