Yamaha 970AC Reference Booklet - Page 30

MIDI Data Format Address Size Data (H) (H) (H) nn 5A 1 28 - 58 nn 5B 1 00 - 7F nn 5C 1 00 - 7F nn 5D 1 00 - 7F nn 5E 1 00 - 7F nn 5F 1 00 - 7F nn 60 1 00 - 5F nn 61 1 28 - 58 nn 62 1 00 - 7F nn 63 1 00 - 7F nn 64 1 00 - 7F nn 65 1 00 - 7F nn 66 1 00 - 7F nn 67 1 00 - 01 nn 68 1 00 - 7F nn 69 1 00 - 7F nn 6A 1 00 - 7F nn 6B 1 00 - 7F nn 6C 1 00 - 7F nn 6D 1 01 - 7F nn 6E 1 01 - 7F TOTAL SIZE 3F nn = PART NUMBER Parameter AC1 PITCH CONTROL AC1 LOW PASS FILTER CONTROL AC1 AMPLITUDE CONTROL AC1 LFO PMOD DEPTH AC1 LFO FMOD DEPTH AC1 LFO AMOD DEPTH AC2 CONTROLLER NUMBER AC2 PITCH CONTROL AC2 LOW PASS FILTER CONTROL AC2 AMPLITUDE CONTROL AC2 LFO PMOD DEPTH AC2 LFO FMOD DEPTH AC2 LFO AMOD DEPTH PORTAMENTO SWITCH PORTAMENTO TIME PITCH EG INITIAL LEVEL PITCH EG ATTACK TIME PITCH EG RELEASE LEVEL PITCH EG RELEASE TIME VELOCITY LIMIT LOW VELOCITY LIMIT HIGH In the case of a DRUM PART, the following parameters will have no effect. • BANK SELECT LSB • MONO/POLY MODE • SCALE TUNING • PORTAMENTO • PITCH EG Description -24...0...+24[semitones] -9600...0...+9450[cent] -100...0...+100[%] 0...127 0...127 0...127 0...95 -24...0...+24[semitones] -9600...0...+9450[cent] -100...0...+100[%] 0...127 0...127 0...127 OFF, ON 0...127 -64...0...+63 -64...0...+63 -64...0...+63 -64...0...+63 1...127 1...127 Default value (H) 40 40 40 00 00 00 11 40 40 40 00 00 00 00 00 40 40 40 40 01 7F < Table 1-5 > MIDI Parameter Change table ( DRUM SETUP ) Address Size (H) (H) 3n rr 00 1 01 1 02 1 03 1 04 1 05 1 06 1 07 1 08 1 09 1 0A 1 0B 1 0C 1 0D 1 0E 1 0F 1 TOTAL SIZE 10 Data (H) 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 01 00 - 01 00 - 01 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F Parameter PITCH COARSE PITCH FINE LEVEL ALTERNATE GROUP PAN REVERB SEND CHORUS SEND VARIATION SEND KEY ASSIGN Rcv NOTE OFF Rcv NOTE ON LOW PASS FILTER CUTOFF FREQUENCY LOW PASS FILTER RESONANCE EG ATTACK RATE EG DECAY1 RATE EG DECAY2 RATE Description -64...0...+63 -64...0...+63[cent] 0...127 OFF,1...127 RND,L63...C...R63 0...127 0...127 0...127 SINGLE , MULTI OFF , ON OFF , ON -64...0...63 -64...0...63 -64...0...63 -64...0...63 -64...0...63 Default value (H) 40 40 depend on the note depend on the note depend on the note depend on the note depend on the note 7F 00 depend on the note 01 40 40 40 40 40 n:Drum Setup Number(0 - 1) rr:note number(0D - 5B) In the following cases, all Drum Setups will be initialized. XG SYSTEM ON received GM SYSTEM ON received DRUM SETUP RESET received (only setup applies) [Note] When a part to which a Drum Setup is assigned receives a program change, the assigned Drum Setup will be initialized. If the same Drum Setup is assigned to two or more parts, changes in Drum Setup parameters (including program changes)will apply to all parts to which it is assigned. 30 CLP-970A