Yamaha CP5 Data List - Page 32

MIDI Data Format +--[SW2]-----------SYSTEM REALTIME MESSAGE | TIMING CLOCK F8H | SYSTEM REALTIME MESSAGE | START FAH | CONTINUE FBH | STOP FCH | ACTIVE SENSING FEH | +--[SW3]-+---------SYSTEM EXCLUSIVE MESSAGE (All in Seq) | | | +---------- | | F0H 43H 0nH 7FH mmH bhH blH ahH amH alH ddH....ddH ccH F7H | | mm = CP5: 10, CP50: 11 | | | +---------- | | F0H 43H 1nH 7FH mmH ahH amH alH ddH.....ddH F7H | | | +---------- | | F0H 43H 2nH 7FH mmH ahH amH alH ddH.....ddH F7H | | | +---------- | F0H 43H 3nH 7FH mmH ahH amH alH F7H | SYSTEM EXCLUSIVE MESSAGE | IDENTITY REQUEST F0H 7EH 0nH 06H 01H F7H | SYSTEM EXCLUSIVE MESSAGE TEST ENTRY F0H 43H 73H 01H 60H 00H F7H [SW2] [SW3] [SW4] [SW5] [SW6] Complies with SYSTEM MIDI Sync setting. (This parameter can be received when it is not set to internal.) MIDI Device Number SYSTEM Bank Select Switch SYSTEM Program Change Switch MIDI Receive Channel and Receive Filter Complies with Receive Channel and Receive Switch. (3) TRANSMIT/RECEIVE DATA (3-1) CHANNEL VOICE MESSAGES (3-1-1) NOTE OFF STATUS NOTE No. VELOCITY Receive only 1000nnnn (8nH) 0kkkkkkk 0vvvvvvv n = 0 - 15 CHANNEL NUMBER k = 0 (C-2) - 127 (G8) v: ignored (3-1-2) NOTE ON/OFF STATUS NOTE NUMBER VELOCITY NOTE ON NOTE OFF 1001nnnn (9nH) 0kkkkkkk 0vvvvvvv (v≠0) 0vvvvvvv (v=0) n = 0 - 15 CHANNEL NUMBER k = 0 (C-2) - 127 (G8) (3-1-3) CONTROL CHANGE STATUS CONTROL NUMBER CONTROL VALUE 1011nnnn (BnH) 0ccccccc 0vvvvvvv n = 0 - 15 CHANNEL NUMBER *TRANSMITTED CONTROL NUMBER c= 0 BANK SEL MSB ; v = 0 - 127 *3 c = 32 BANK SEL LSB ; v = 0 - 127 *3 c = 64 SUSTAIN SWITCH ; v = 0, 127 c = 0...95 ASSIGNABLE CONTROLLERS ; v = 0 - 127 *4 The Sequencer Part will play back all recorded control change messages. *RECEIVED CONTROL NUMBER c= 0 BANK SEL MSB ; v = 0 - 127 *3 c = 32 BANK SEL LSB ; v = 0 - 127 *3 c= 1 MODULATION ; v = 0 - 127 c= 5 PORTAMENTO TIME ; v = 0 - 127 *2 c= 6 DATA ENTRY MSB ; v = 0 - 127 *1 c = 38 DATA ENTRY LSB ; v = 0 - 127 *1 c= 7 MAIN VOLUME ; v = 0 - 127 c = 10 c = 11 PAN EXPRESSION ; v = 0 - 127 ; v = 0 - 127 c = 31 c = 64 c = 65 EG SUSTAIN LEVEL SUSTAIN SWITCH PORTAMENTO SWITCH ; v = 0: -64 - 64: 0 - 127: +63 *2 ; v = 0 - 63: OFF, 64 - 127: ON *2 ; v = 0 - 63: OFF, 64 - 127: ON *2 c = 66 SOSTENUTO ; v = 0 - 63: OFF, 64 - 127: ON *2 c = 71 c = 72 HARMONIC CONTENT EG RELEASE TIME ; v = 0: -64 - 64: 0 - 127: +63 ; v = 0: -64 - 64: 0 - 127: +63 *2 c = 73 EG ATTACK TIME ; v = 0: -64 - 64: 0 - 127: +63 c = 74 c = 75 BRIGHTNESS EG DECAY TIME ; v = 0: -64 - 64: 0 - 127: +63 ; v = 0: -64 - 64: 0 - 127: +63 c = 91 EFFECT1 DEPTH ; v = 0 - 127 c = 93 EFFECT3 DEPTH ; v = 0 - 127 c = 96 DATA ENTRY INC ; v = 127 *1 c = 97 DATA ENTRY DEC ; v = 127 *1 c = 0..95 ASSIGNABLE CONTROLLER ; v = 0 - 127 *4 All Control Change events can be recorded to the sequence data. *1 Used only when a value is set using RPN. *2 Invalid with Drum Voices. *3 Relation between BANK CHANGE and PROGRAM is as follows: CATEGORY MSB LSB Performance Preset 1 63 64 Preset 2 63 65 Preset 3 63 66 User 1 63 67 User 2 63 68 User 3 63 69 External 1 63 70 External 2 63 71 External 3 63 72 PROGRAM No. 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) 0...39 (1...40) *4 The default CONTROL NUMBERS of ASSIGNABLE CONTROLLER are as follows: FOOT CONTROLLER 1 11 FOOT CONTROLLER 2 4 FOOT SWITCH 88 PORTAMENTO TIME is set the time it takes for the pitch to reach the next note played when PORTAMENT SWITCH is set to on. 0: shortest time; 127: longest time PAN position relatively changes according to the value for each performance part. EFFECT1 DEPTH controls reverb send level. HARMONIC CONTENT adjusts the resonance preset for each performance. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The larger the value more resonant sound will be produced. The effective range may be narrower than the range you can designate depending on the selected voice. The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the envelopes preset for each performance. Setting these values add to or subtract from the center value, 64, since these are offset parameters. BRIGHTNESS adjusts the cutoff frequency preset for each performance. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The smaller the value the cutoff frequency will be lowered. The effective range may be narrower than the range you can designate depending on the selected voice. Bank Select will be actually executed when the Program Change message is received. Bank Select and Program Change numbers that are not supported by Yamaha will be ignored. (3-1-4) PROGRAM CHANGE STATUS PROGRAM NUMBER 1100nnnn (CnH) 0ppppppp n = 0 - 15 CHANNEL NUMBER p = 0 - 127 (3-1-5) CHANNEL AFTER TOUCH STATUS VALUE 1101nnnn (DnH) 0vvvvvvv n = 0 - 15 CHANNEL NUMBER v = 0 - 127 AFTER TOUCH VALUE (3-1-6) PITCH BEND CHANGE STATUS 1110nnnn (EnH) LSB 0vvvvvvv MSB 0vvvvvvv Transmitted with a resolution of 7 bits. n = 0 - 15 CHANNEL NUMBER PITCH BEND CHANGE LSB PITCH BEND CHANGE MSB (3-2) CHANNEL MODE MESSAGES STATUS CONTROL NUMBER CONTROL VALUE 1011nnnn (BnH) 0ccccccc 0vvvvvvv n = 0 - 15 CHANNEL NUMBER c = CONTROL NUMBER v = DATA VALUE (3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0) All the sounds currently played including the channel messages such as note-on and hold-on in a certain channel are muted when receiving this message. (3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0) Resets the values set for the following controllers. PITCH BEND CHANGE 0 (center) MODULATION 0 (minimum) EXPRESSION 127 (maximum) FOOT CONTROLLER 127 (maximum) SUSTAIN SWITCH 0 (off) SOSTENUTO SWITCH 0 (off) RPN Not assigned; No change Doesn't reset the following data: PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL, RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3,PORTAMENTO SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING (3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0) All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or Sostenuto is on, notes will continue sounding until these are turned off. (3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0) Performs the same function as when receiving ALL SOUND OFF. Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1. (3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0) Performs the same function as when receiving ALL SOUND OFF. Sets VOICE RECEIVE CHANNEL to "OMNI ON." (3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0) Sets Part Mode to "mono." (3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0) Sets Part Mode to "poly." (3-3) REGISTERED PARAMETER NUMBER STATUS LSB RPN LSB MSB RPN MSB DATA ENTRY MSB DATA VALUE DATA ENTRY LSB DATA VALUE 1011nnnn (BnH) 01100100 (64H) 0ppppppp 01100101 (65H) 0qqqqqqq 00000110 (06H) 0mmmmmmm 00100110 (26H) 0lllllll n = 0 - 15 CHANNEL NUMBER p = RPN LSB (Refer to the table as shown below.) q = RPN MSB (Refer to the table as shown below.) m = Data Value l = Data Value First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB. RPN D.ENTRY LSB MSB MSB LSB 00H 00H mmH --- 01H 00H mmH llH 02H 00H mmH --7FH 7FH --- --- PARAMETER NAME DATA RANGE PITCH BEND SENSITIVITY 00H - 0CH (0 - 12 semitones) MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH} (-8192*100/8192) - 0 - (+8192*100/8192) MASTER COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones) RPN RESET RPN numbers will be left not designated. The internal values are not affected. CP5 / CP50 Data List 32