Yamaha CP50 Reference Manual - Page 43

Settings for All Performances Master Compressor Block This section describes the parameters used to configure the compressor applied to all of the Performances on your CP5 or CP50. These settings are made via the Master Compressor screen, which contains seven pages. Edit Sequence [Press and hold the [MASTER COMPRESSOR] button (for at least one second)  Navigate to the required page using the [- PAGE] and [PAGE 3] buttons  Turn Knobs 1 to 3 Page On-screen name (and full name) Description 1 LowTh (Low Threshold) This parameter is used to set the input-signal level at which the compressor starts to process the sound in the low-frequency band. Setting values: -54dB to -6dB LowAtk (Low Attack) This parameter is used to set the amount of time that elapses between arrival of an input signal and activation of compression in the low-frequency band. Setting values: 1ms to 200ms 2 LowRat (Low Ratio) This parameter is used to set the compression ratio for the low-frequency band. Setting values: 1.0 to 20.0 LowGain (Low Gain) This parameter is used to set the output level of the low-frequency band. Setting values: -∞ to +18dB 3 MidTh (Mid Threshold) This parameter is used to set the input-signal level at which the compressor starts to process the sound in the mid-frequency band. Setting values: -54dB to -6dB MidAtk (Mid Attack) This parameter is used to set the amount of time that elapses between arrival of an input signal and activation of compression in the mid-frequency band. Setting values: 1ms to 200ms 4 MidRat (Mid Ratio) This parameter is used to set the compression ratio for the mid-frequency band. Setting values: 1.0 to 20.0 MidGain (Mid Gain) This parameter is used to set the output level of the mid-frequency band. Setting values: -∞ to +18dB 5 HiTh (High Threshold) This parameter is used to set the input-signal level at which the compressor starts to process the sound in the high-frequency band. Setting values: -54dB to -6dB HiAtk (High Attack) This parameter is used to set the amount of time that elapses between arrival of an input signal and activation of compression in the high-frequency band. Setting values: 1ms to 200ms 6 HiRat (High Ratio) This parameter is used to set the compression ratio for the high-frequency band. Setting values: 1.0 to 20.0 HiGain (High Gain) This parameter is used to set the output level of the high-frequency band. Setting values: -∞ to +18dB 7 DivFrqL This parameter is used to set the low-to-mid frequency when splitting the sound (Dividing Frequency into three bands. Low) Setting values: 16Hz to 20kHz DivFrqH (Dividing Frequency High) This parameter is used to set the mid-to-high frequency when splitting the sound into three bands. Setting values: 16Hz to 20kHz CmnRel (Common Release) Affecting all three compression bands, this parameter is used to set the amount of time that elapses until the sound is no longer being compressed. Setting values: 10ms to 3000ms Internal Design of the CP5 & CP50 Reference Left & Right Parts 3
[VOICE] 3
[PRE-AMP] 3
[MOD-FX] 3
[PWR-AMP] (CP5 only) 3
[LEFT1]/[LEFT2]/[RIGHT1]/ [RIGHT2] (CP5) [LEFT]/[RIGHT] (CP50) 3
[COMMON] Song Setting Area 3
[SONG SETTING] 3
[RECORD] TRACK Part 3
[TRACK] MIC INPUT Part 3
[MIC INPUT] (CP5 only) Settings for All Parts 3
[REVERB] Settings for All Performances 3
[MASTER COMPRESSOR] 3
[UTILITY] 3
[FILE] Appendix 43 CP5/CP50 Reference Manual