Yamaha CS6R Data List - Page 28

3) TRANSMIT/RECEIVE DATA (3-1) CHANNEL VOICE MESSAGES CS6R transmits BC and A-C/1-2 of ASSIGNABLE CONTROLLER, and the data from the Sequencer Part. (3-1-1) NOTE OFF STATUS NOTE NUMBER VELOCITY Receive only. 1000nnnn(8nH) 0kkkkkkk 0vvvvvvv n = 0 ~ 15 CHANNEL NUMBER k = 0 (C-2) ~ 127 (G8) ignores "v" (3-1-2) NOTE ON/OFF STATUS NOTE NUMBER VELOCITY 1001nnnn(9nH) 0kkkkkkk 0vvvvvvv(v≠0) 0vvvvvvv(v=0) n = 0 ~ 15 CHANNEL NUMBER k = 0 (C-2) ~ 127 (G8) NOTE ON NOTE OFF (3-1-3) CONTROL CHANGE STATUS 1011nnnn(BnH) CONTROL NUMBER 0ccccccc CONTROL VALUE 0vvvvvvv n = 0 ~ 15 CHANNEL NUMBER * TRANSMITTED CONTROL NUMBER c= 0 BANK SEL MSB ; v = 0,63,127 *3 c = 32 BANK SEL LSB ; v = 0,1,8,9,24,25,32,40,41,64,65 *3 c= 1 MODULATION ; v = 0 - 127 c= 5 PORTAMENTO TIME ; v = 0 - 127 *4 c= 7 MAIN VOLUME ; v = 0 - 127 c = 10 PAN ; v = 0 - 127 *4 c = 11 EXPRESSION ; v = 0 - 127 c = 31 EG SUSTAIN LEVEL ; v = 0:-64 - 64:0 - 127:+63 *4,*5 c = 64 SUSTAIN SWITCH ; v = 0, 127 c = 65 PORTAMENTO SWITCH ; v = 0-63:OFF , 64-127:ON *4 c = 71 FILTER RESONANCE ; v = 0:-64 - 64:0 - 127:+63 *4 c = 72 EG RELEASE TIME ; v = 0:-64 - 64:0 - 127:+63 *4 c = 73 EG ATTACK TIME ; v = 0:-64 - 64:0 - 127:+63 *4 c = 74 FILTER CUTOFF FREQ ; v = 0:-64 - 64:0 - 127:+63 *4 c = 75 EG DECAY TIME ; v = 0:-64 - 64:0 - 127:+63 *4 c = 91 REVERB SEND ; v = 0 - 127 *4 c = 93 CHORUS SEND ; v = 0 - 127 *4 c = 0..95 ASSIGNABLE CONTROLLER ; v = 0 - 127 *6 The Sequencer Part will play back all the recorded control change messages. * RECEIVED CONTROL NUMBER c= 0 BANK SEL MSB c = 32 BANK SEL LSB c= 1 MODULATION c= 5 PORTAMENTO TIME c= 6 DATA ENTRY MSB c = 38 DATA ENTRY LSB c= 7 MAIN VOLUME c = 10 PAN c = 11 EXPRESSION c = 31 EG SUSTAIN LEVEL c = 64 SUSTAIN SWITCH c = 65 PORTAMENTO SWITCH c = 66 SOSTENUTO c = 71 HARMONIC CONTENT c = 72 EG RELEASE TIME c = 73 EG ATTACK TIME c = 74 BRIGHTNESS c = 75 EG DECAY TIME c = 91 EFFECT1 DEPTH c = 93 EFFECT3 DEPTH c = 96 DATA ENTRY INC c = 97 DATA ENTRY DEC c = 0..95 ASSIGNABLE CONTROLLER c = 0..95 ARPEGGIO SW c = 0..95 ARPEGGIO HOLD ; v = 0 - 127 *3 ; v = 0 - 127 *3 ; v = 0 - 127 ; v = 0 - 127 *2 ; v = 0 - 127 *1 ; v = 0 - 127 *1 ; v = 0 - 127 ; v = 0 - 127 ; v = 0 - 127 ; v = 0:-64 - 64:0 - 127:+63 *2,*5 ; v = 0-63:OFF , 64-127:ON *2 ; v = 0-63:OFF , 64-127:ON *2 ; v = 0-63:OFF , 64-127:ON *2 ; v = 0:-64 - 64:0 - 127:+63 ; v = 0:-64 - 64:0 - 127:+63 ; v = 0:-64 - 64:0 - 127:+63 ; v = 0:-64 - 64:0 - 127:+63 ; v = 0:-64 - 64:0 - 127:+63 *2 ; v = 0 - 127 ; v = 0 - 127 ; v = 127 *1 ; v = 127 *1 ; v = 0 - 127 *6 ; v = 0-63:OFF , 64-127:ON *6 ; v = 0-63:OFF , 64-127:ON *6 *1 Used only when a value is set using RPN. *2 Invalid with Drum Voices. *3 Relation between BANK CHANGE and PROGRAM is as follows: CATEGORY |MSB |LSB |PROGRAM No Displayed on LCD Normal Voice Internal |0 |0 |0..127 (1..128) Drum Voice Internal |127 |0 |0..1 (1..2) Normal Voice Preset 1 |63 |0 |0..127 (1..128) Preset 2 |63 |1 |0..127 (1..128) Internal |63 |8 |0..127 (1..128) External |63 |9 |0..127 (1..128) Plug-in Voice Plug-in 1 |63 |24 |0..63 (1..64) Plug-in 2 |63 |25 |0..63 (1..64) Drum Voice Preset |63 |32 |0..7 (1..8) Internal |63 |40 |0..1 (1..2) External |63 |41 |0..1 (1..2) Performance Internal |63 |64 |0..127 (1..128) External |63 |65 |0..63 (1..64) Phrase Clip Internal |63 |104 |0..3 (1..4) *4 CS6x only. *5 Transmitted/received only when MODE2 is selected in CONTROL CHANGE MODE. *6 The default CONTROL NUMBERs of ASSIGNABLE CONTROLLER are as follows: BREATH CONTROLLER 2 FOOT CONTROLLER 4 (Transmit: CS6x and S80 only) SCENE CONTROL 14 (Transmit/Receive: CS6x only) KNOB 1 16 KNOB 2 17 KNOB A 18 KNOB B 19 KNOB C 20 RIBBON CONTROLLER 22 (Transmit: CS6x only) CONTROL SLIDER 7 (Transmit/Receive: S80 only) FOOT SWITCH 88 (Transmit: CS6x, S80 only) ARPEGGIO HOLD 89 (Transmit: CS6x only) ARPEGGIO SWITCH 90 (Transmit: CS6x only) PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO SWITCH is set to on. PAN position relatively changes according to the preset value for each voice. EFFECT1 DEPTH controls reverb send level. EFFECT3 DEPTH controls chorus send level. HARMONIC CONTENT adjusts the resonance preset for each voice. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The larger the value more resonant sound will be produced. The effective range may be narrower than the range you can designate depending on the selected voice. The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the envelopes preset for each voice. Setting these values add to or subtract from the center value, 64, since these are offset parameters. BRIGHTNESS adjusts the cutoff frequency preset for each voice. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The smaller the value the cutoff frequency will be lowered. The effective range may be narrower than the range you can designate depending on the selected voice. Bank Select will be actually executed when the Program Change message is received. Bank Select and Program Change numbers that are not supported by Yamaha will be ignored. (3-1-4) PROGRAM CHANGE STATUS 1100nnnn(CnH) PROGRAM NUMBER 0ppppppp n = 0 ~ 15 CHANNEL NUMBER p = 0 ~ 127 (3-1-5) CHANNEL AFTER TOUCH STATUS 1101nnnn(DnH) VALUE 0vvvvvvv n = 0 ~ 15 CHANNEL NUMBER v = 0 ~ 127 AFTER TOUCH VALUE (3-1-6) PITCH BEND CHANGE STATUS 1110nnnn(EnH) n = 0 ~ 15 CHANNEL NUMBER LSB 0vvvvvvv PITCH BEND CHANGE LSB MSB 0vvvvvvv PITCH BEND CHANGE MSB Transmitted with a resolution of 7 bits. (3-2) CHANNEL MODE MESSAGES STATUS 1011nnnn(BnH) CONTROL NUMBER 0ccccccc CONTROL VALUE 0vvvvvvv n = 0 ~ 15 CHANNEL NUMBER c = CONTROL NUMBER v = DATA VALUE (3-2-1) ALL SOUNDS OFF (CONTROL NUMBER = 78H , DATA VALUE = 0) All the sounds currently played including the channel messages such as note-on and hold-on in a certain channel are muted when receiving this message. (3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H , DATA VALUE = 0) Resets the values set for the following controllers. PITCH BEND CHANGE 0 (center) CHANNEL AFTER TOUCH 0 (minimum) MODULATION 0 (minimum) EXPRESSION 127 (maximum) BREATH CONTROLLER 127 (maximum) FOOT CONTROLLER 127 (maximum) RIBBON CONTROLLER 0 (center) KNOB 1 0 (center) KNOB 2 0 (center) SUSTAIN SWITCH 0 (off) SOSTENUTO SWITCH 0 (off) RPN Not assigned; No change Doesn't reset the following data: PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN. HARMONIC CONTENT, SUSTAIN LEVEL, RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3, PORTAMENTO SWITCH PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING ASSIGNABLE CONTROLLER (3-2-3) ALL NOTES OFF (CONTROL NUMBER = 7BH , DATA VALUE = 0) All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or Sostenuto is on, notes will continue sounding until these are turned off. (3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH , DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1. (3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH , DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. Sets VOICE RECEIVE CHANNEL to "OMNI ON." (3-2-6) MONO (CONTROL NUMBER = 7EH , DATA VALUE = 0..16) Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the channel will be Mode4(m = 1). In VOICE MODE, the mode can be Mode2(m=1) according to VOICE RECEIVE CHANNEL. (3-2-7) POLY (CONTROL NUMBER = 7FH , DATA VALUE = 0) Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3. In VOICE MODE, the mode can be Mode1 according to VOICE RECEIVE CHANNEL. (3-3) REGISTERED PARAMETER NUMBER STATUS LSB RPN LSB MSB RPN MSB DATA ENTRY MSB DATA VALUE DATA ENTRY LSB DATA VALUE 1011nnnn(BnH) 01100100(64H) 0ppppppp 01100101(65H) 0qqqqqqq 00000110(06H) 0mmmmmmm 00100110(26H) 0lllllll n = 0 ~ 15 CHANNEL NUMBER p = RPN LSB(Refer to the table as shown below) q = RPN MSB(Refer to the table as shown below) m = Data Value l = Data Value First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB. RPN D.ENTRY LSB MSB MSB LSB PARAMETER NAME DATA RANGE 00H 00H mmH --01H 00H mmH llH 02H 00H mmH --7FH 7FH --- --- PITCH BEND SENSITIVITY MASTER FINE TUNE MASTER COARSE TUNE RPN RESET 00H - 18H (0 - 24 semitones) {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH} (-8192*100/8192) - 0 - (+8192*100/8192) 28H - 40H - 58H (-24 - 0 - +24 semitones) RPN numbers will be left not designated. The internal values are not affected. (3-4) NON-REGISTERED PARAMETER NUMBER There are no applicable parameters. (3-5) SYSTEM REAL TIME MESSAGES (3-5-1) ACTIVE SENSING STATUS 11111110(FEH) Transmitted at every 200 msec. Once this code is received, the instrument starts sensing. When no status nor data is received for over approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch are forcibly turned off. In this case, each control data will be reset to a certain value. (3-6) SYSTEM EXCLUSIVE MESSAGE (3-6-1)UNIVERSAL NON REALTIME MESSAGE (3-6-1-1)GENERAL MIDI MODE ON F0H 7EH 7FH 09H 01H F7H Received only when SYSTEM Receive GM/XG on is set to on in PERFORMANCE MODE. The Part values will be reset according to the SYSTEM Internal Part settings. 28