Yamaha EMX2000 Owner's Manual - Page 6

Stereo sub input Effect control EFFECT - emx2000e

Get Yamaha EMX2000 PDF manuals and user guides View all Yamaha EMX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

5 6 Effect control (EFFECT) For each channel, this controls the amount of signal that is sent to the EFFECT bus. The signal of the EFFECT bus is sent to the EFFECT jack (input/output panel A). It is also sent to the built-in effect when the ON switch P in the EFFECT section is turned on. Note: The amount of signal that is sent to the EFFECT bus from each channel will be affected not only by the setting of the EFFECT control, but also by the setting of the channel fader 0 (post-fader send). 7 PAN (panpot) control (Channels 1~8) The PAN knobs set the stereo position of the signal that is sent to the STEREO bus. 8 BAL (balance) control (Channels 9/10~ 11/12) The BAL knobs set the balance between the left and right channels, and assign the signals received at inputs 9/10~11/12 to the STEREO bus. 9 PFL (pre-fader listen) switch When the PFL switch is turned on, the signal of the corresponding channel at the point after the equalization but before the channel fader is sent to the PHONES/C-R OUT jack (input/output panel B). This is useful when you wish to listen to a particular channel through the headphones. Note: You can monitor the signal through the headphones even if the fader of the corresponding channel is set to the lowest level. The switch operation does not affect the signal sent to the STEREO bus, MONITOR 1/2 buses, or the EFFECT bus. 0 Channel fader This controls the output level of the input channel signal. s Stereo sub input section In this section, you can adjust the input level of external equipment connected to the ST SUB 1/2 jacks on the input/output panel. MONI 1 0 10 MONI 2 0 10 ST 0 10 PFL ST SUB 1 MONI 1 0 10 MONI 2 0 10 ST 0 10 PFL ST SUB 2 A B C D A B C D A MONI 1 (monitor 1) control The MONI 1 knob adjusts the amount of the signal sent from the ST SUB 1 and 2 jacks (input/ output panel 4) to the MONITOR 1 bus. B MONI 2 (monitor 2) control The MONI 2 knob adjusts the amount of the signal sent from the ST SUB 1 and 2 jacks to the MONITOR 2 bus. C ST (stereo) control The ST knob adjusts the amount of stereo signal sent from the ST SUB 1 and 2 jacks to the STEREO bus. Note: The ST control setting does not affect the level of the signal sent to the MONITOR 1/2 buses (pre-fader send). D PFL (pre-fader listen) switch When this switch is turned on, the signal at the point before the ST control knob C is sent to the PHONES/C-R OUT jack (input/output panel B ). EMX2000-Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
5
EMX2000—Owner’s Manual
6
Effect control (EFFECT)
For each channel, this controls the amount of sig-
nal that is sent to the EFFECT bus.
The signal of the EFFECT bus is sent to the
EFFECT jack (input/output panel
A
). It is also
sent to the built-in effect when the ON switch
P
in the EFFECT section is turned on.
7
PAN (panpot) control (Channels 1~8)
The PAN knobs set the stereo position of the sig-
nal that is sent to the STEREO bus.
8
BAL (balance) control (Channels 9/10~
11/12)
The BAL knobs set the balance between the left
and right channels, and assign the signals
received at inputs 9/10~11/12 to the STEREO
bus.
9
PFL (pre-fader listen) switch
When the PFL switch is turned on, the signal of
the corresponding channel at the point after the
equalization but before the channel fader is sent
to the PHONES/C-R OUT jack (input/output
panel
B
). This is useful when you wish to listen
to a particular channel through the headphones.
0
Channel fader
This controls the output level of the input chan-
nel signal.
■
Stereo sub input section
In this section, you can adjust the input level of
external equipment connected to the ST SUB 1/2
jacks on the input/output panel.
A
MONI 1 (monitor 1) control
The MONI 1 knob adjusts the amount of the sig-
nal sent from the ST SUB 1 and 2 jacks (input/
output panel
4
) to the MONITOR 1 bus.
B
MONI 2 (monitor 2) control
The MONI 2 knob adjusts the amount of the sig-
nal sent from the ST SUB 1 and 2 jacks to the
MONITOR 2 bus.
C
ST (stereo) control
The ST knob adjusts the amount of stereo signal
sent from the ST SUB 1 and 2 jacks to the STE-
REO bus.
D
PFL (pre-fader listen) switch
When this switch is turned on, the signal at the
point before the ST control knob
C
is sent to the
PHONES/C-R OUT jack (input/output panel
B
).
Note:
The amount of signal that is sent to the
EFFECT bus from each channel will be affect-
ed not only by the setting of the EFFECT con-
trol, but also by the setting of the channel fader
0
(post-fader send).
Note:
You can monitor the signal through the
headphones even if the fader of the corre-
sponding channel is set to the lowest level. The
switch operation does not affect the signal sent
to the STEREO bus, MONITOR 1/2 buses, or
the EFFECT bus.
Note:
The ST control setting does not affect
the level of the signal sent to the MONITOR
1/2 buses (pre-fader send).
PFL
PFL
10
0
MONI 1
10
0
MONI 2
10
0
ST
10
0
MONI 1
10
0
MONI 2
10
0
ST
ST SUB 1
ST SUB 2
C
D
D
A
B
C
B
A