Yamaha EMX660 Owner's Manual - Page 14

14 Example setups Example setups This section provides some ways in which the EMX660 can be used, and explains connections and operation. As a conference PA system/installed sound system Here is an example of using the EMX660 as a conference PA system or as an installed sound system. Main Speakers 1 HIGH Power AMP 1 A/B 2 HIGH 3 HIGH 4 HIGH 5 HIGH 6 HIGH -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 MID MID MID MID MID MID -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 LOW LOW LOW LOW LOW LOW -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 MONI MONI MONI MONI MONI MONI 0 10 0 10 0 10 0 10 0 10 0 10 EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT 0 10 0 10 0 10 0 10 0 10 0 10 LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL 0 10 0 10 0 10 0 10 PAD PAD PAD PAD 1 2 3 4 0 10 5 0 10 6 VO. ECHO 1 VO. ECHO 2 VO. REV. 1 VO. REV. 2 HALL. 1 HALL. 2 ROOM PLATE ON DIGITAL EFFECT Power AMP 2 A/B +12 +12 +6 • 6 • 6 +3 • 0 • 0 0 • • 6 6 -5 • • -12 -12 -10 125 250 500 1k 2k 4k 8k POWER ON OFF PHANTOM 0 10 EFFECT RTN 0 10 TAPE IN MONITOR 0 10 MASTER +12 +12 +6 • 6 • 6 +3 • 0 • 0 0 • 6 • 6 -5 • • -12 -12 -10 125 250 500 1k 2k 4k 8k 0 10 EFFECT RTN 0 10 AUX IN 0 10 TAPE IN MAIN 0 10 MASTER 2AMPs 300W 300W 1 2 LIMITER MAIN BRIDGE MAIN MAIN MAIN MONITOR POWER AMP Hi-Z Hi-Z Hi-Z Hi-Z 1 LINE 2 1 INST 2 EFFECT OUT Lo-Z Lo-Z Lo-Z Lo-Z MIC MIC FOOT SW MONITOR TAPE REC 1 IN OUT1 AUX IN 2 MAIN 2 SEE REAR PANEL CAUTION EEEngine INPUT OUTPUT Power amp select switch MAIN BRIDGE MAIN MAIN MAIN MONITOR Microphone CD Player Cassette Deck Connections • Connect mics to channel inputs 1-6. • If you wish to use an external device such as a CD player or LD player, connect the outputs of the device to the TAPE IN jacks of the EMX660. Note: A CD/LD player or cassette deck can also be connected to the LINE jacks of channel 5. • If you wish to record the audio to a cassette deck, connect the REC OUT jacks of the EMX660 to the input jacks of the cassette deck. • Connect the main speakers to the A/B jacks of the POWER AMP 1/2, and set the power amp select switch to "MAIN-MAIN." Playing back a CD player 1 Turn the power on in the order of peripheral devices © EMX660. 2 Adjust the MASTER control of the MAIN section to the √ position. 3 Start playback on the CD player, and use the MAIN section TAPE IN control to adjust the level so that the 0 LED of the MAIN section peak level meter does not light. EMX660-Owner's Manual