Yamaha HTR-5250 Owner's Manual - Page 52

Advanced Information, Setup codes, To use a second and third VCR

Get Yamaha HTR-5250 PDF manuals and user guides View all Yamaha HTR-5250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

PRESET REMOTE CONTROL Advanced Information s Setup codes You can set the code for the manufacturer of your component in each position of the selector dial. 1 Turn on your component to be used. 2 Set the selector dial to the desired position for the component (TAPE/MD, CD, DVD/LD, etc.). 3 Press i (right) and j (left) at the same time for about four seconds. The indicator flashes twice. s To use a second (and third) VCR You can control a second (and third) VCR in the CBL/SAT and DVD MENU positions if a cable TV or satellite tuner, or DVD player is not being used. Note • If you want to control a second (and third) VCR in the DVD MENU position, you must set the code for an LD player in the DVD/LD position. 1 Turn on the VCR to be used. 2 Set the selector dial to the CBL/SAT or DVD MENU position. 3 Press i (right) and j (left) at the same time for about four seconds. The indicator flashes twice. 4 Use the numeric buttons to enter the four-digit manufacturer's code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and re-enter the code. 5 Press AV POWER (or any other button) on the remote control to check if you have set the code correctly. If your component cannot be controlled with the remote control, try setting another code for the same manufacturer. Notes • You can set only one code for one position. • In the DVD/LD and DVD MENU positions: Be sure to set the selector dial to the DVD/LD position before entering the code for the DVD/LD player. The code set in the DVD/LD position is also simultaneously set in the DVD MENU position. You cannot set the code for a DVD player when the selector dial is set to the DVD MENU position. • If your component does not respond to any of the codes listed for the manufacturer, use the original remote control supplied with your component. 4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and re-enter the code. 5 Press AV POWER (or any other button) on the remote control to check if you have set the code correctly. If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
48
Advanced Information
■
Setup codes
You can set the code for the manufacturer of your
component in each position of the selector dial.
1
Turn on your component to be used.
2
Set the selector dial to the
desired position for the
component (TAPE/MD, CD,
DVD/LD, etc.).
3
Press
i
(right) and
j
(left)
at the same time for about
four seconds.
The indicator flashes twice.
4
Use the numeric buttons to
enter the four-digit
manufacturer’s code for
the component to be used.
Make sure that the
indicator flashes twice.
If the indicator does not flash or
flashes rapidly several times,
repeat step 3 and re-enter the
code.
5
Press AV POWER (or any other button) on the
remote control to check if you have set the
code correctly.
If your component cannot be
controlled with the remote
control, try setting another code
for the same manufacturer.
Notes
•
You can set only one code for one position.
•
In the DVD/LD and DVD MENU positions:
Be sure to set the selector dial to the DVD/LD position before
entering the code for the DVD/LD player. The code set in the
DVD/LD position is also simultaneously set in the DVD MENU
position. You cannot set the code for a DVD player when the
selector dial is set to the DVD MENU position.
•
If your component does not respond to any of the codes listed for
the manufacturer, use the original remote control supplied with
your component.
PRESET REMOTE CONTROL
■
To use a second (and third) VCR
You can control a second (and third) VCR in the CBL/SAT
and DVD MENU positions if a cable TV or satellite tuner,
or DVD player is not being used.
Note
•
If you want to control a second (and third) VCR in the DVD
MENU position, you must set the code for an LD player in the
DVD/LD position.
1
Turn on the VCR to be used.
2
Set the selector dial to the
CBL/SAT or DVD MENU
position.
3
Press
i
(right) and
j
(left)
at the same time for about
four seconds.
The indicator flashes twice.
4
Use the numeric buttons to
enter the four-digit code
for the second (and third)
VCR. Make sure that the
indicator flashes twice.
If the indicator does not flash or
flashes rapidly several times,
repeat step 3 and re-enter the
code.
5
Press AV POWER (or any other button) on the
remote control to check if you have set the
code correctly.
If the VCR cannot be controlled
with the remote control, try
setting another code for the
same manufacturer.