Yamaha RX-V861 MCXSP10 Manual - Page 85

3 OPTION MENU Use this menu to adjust the optional system parameters. p p MANUAL SETUP 3 OPTION MENU 1/2 . A)DISPLAY SET B)MEMORY GUARD C)AUDIO SELECT D)PARAM. INI [ ]/[ ]:Up/Down [ENTER]:Enter p p MANUAL SETUP 3 OPTION MENU 2/2 . E)ZONE2 SET F)XM RADIO SET G)DOCK SET [ ]/[ ]:Up/Down [ENTER]:Enter ■ Display settings A)DISPLAY SET p p OPTION MENU A)DISPLAY SET 1/2 . VIDEO-CONV.;;;ON HDMI UP-SCALING >*THRGH *480p *1080i *720p [ ]/[ ]:Up/Down [ ]/[[]:Select p p OPTION MENU A)DISPLAY SET 2/2 . DIMMER;;;;;;;;;0 OSD-SHIFT;;;;;;0 OSD-SOURCE;;;30s OSD-AMP;;;;;;30s FL SCROLL;;;CONT [ ]/[ ]:Up/Down [ ]/[[]:Select [ [ y As a result of the parameter setting in "DISPLAY SET", no screen may appear on the video monitor. In such a case, use "V.RESET" (see page 96) to set the "VIDEO CONV.", "HDMI UP-SCALING", "HDMI ASP" and "OSD SHIFT" settings to default. Video conversion VIDEO CONV. Use this feature to set whether to convert the video signals input at the VIDEO, S VIDEO and COMPONENT VIDEO jacks. Choices: ON, OFF • Select "ON" to convert video signals (composite, S-video or component) to composite, S-video, component or HDMI video signals. • Select "OFF" not to convert any signals. Notes • This unit does not convert between 480 line video signals and 576 line video signals. • The analog component video signals with 480i (NTSC)/576i (PAL) of resolution are converted to the S-video or composite video signals and output at the S VIDEO MONITOR OUT and VIDEO MONITOR OUT jacks. • The converted video signals are only output at the MONITOR OUT jacks. When recording a video source, you must make the same type of video connections between each component. • When composite video or S-video signals from a VCR are converted to component video signals, the picture quality may suffer depending on your VCR. • Unconventional signals input at the composite video or S-video jacks cannot be converted or may be output abnormally. In such cases, set "VIDEO CONV." to "OFF". • When non-standard video signals (such as video signals from a game console) are input, this unit may not convert the signals even if you set "VIDEO CONV." to "ON". Customizing this unit (MANUAL SETUP) HDMI Up-scaling HDMI Up-Scaling Use this feature to select the resolution of the HDMI upconversion of the analog video signals input at the VIDEO, S VIDEO and COMPONENT VIDEO jacks so that the up-scaled video signals are output at the HDMI OUT jack. This unit up-scales the analog video signals as follows: • 480i (NTSC)/576i (PAL) → 480p/576p, 1080i or 720p • 480p/576p → 1080i or 720p Press Dl / h to select the desired resolution and then DENTER to confirm the selection. Choices: THRGH, 480p (or 576p), 1080i, 720p • Select "THRGH" (through) not to up-scale any analog video signals. • Select "480p" (or "576p"), "1080i" or "720p" to up- scale analog video signals to 480p or 576p, 1080i or 720p of resolution. Notes • The "HDMI UP-SCALING" parameter appears only when you set "VIDEO CONV." to "ON". • If you connect your video monitor via HDMI connection, this unit automatically detects the available video signal resolution of the video monitor, and an asterisk(*) appears on the left of the available video signal resolution(s). • If this unit cannot detect the available video signal resolution(s) of the connected video monitor, set "MON. CHK" (see page 93) to "SKIP" and then set "HDMI UP-SCALING" again. • This unit does not convert between 480 line video signals and 576 line video signals. The resolution availability ("480p" or "576p") depending on the model. However, when the video monitor is connected to this unit via HDMI, the available resolutions of the monitor appears in the OSD. ADVANCED OPERATION English 81 En