Yamaha S70 S90 XS/S70 XS Data List - Page 100
S90 Xs/s70 Xs Data List, Midi Data Format, 2 Channel Mode Messages, 3 Registered Parameter Number
View all Yamaha S70 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 100 highlights
MIDI Data Format PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO SWITCH is set to on. PAN position relatively changes according to the preset value for each voice. EFFECTS 1 DEPTH controls reverb send level. EFFECTS 3 DEPTH controls chorus send level. HARMONIC CONTENT adjusts the resonance preset for each voice. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The larger the value more resonant sound will be produced. The effective range may be narrower than the range you can designate depending on the selected voice. The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the envelopes preset for each voice. Setting these values add to or subtract from the center value, 64, since these are offset parameters. BRIGHTNESS adjusts the cutoff frequency preset for each voice. Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter. The smaller the value the cutoff frequency will be lowered. The effective range may be narrower than the range you can designate depending on the selected voice. Bank Select will be actually executed when the Program Change message is received. Bank Select and Program Change numbers that are not supported by Yamaha will be ignored. (3-1-4) PROGRAM CHANGE STATUS PROGRAM NUMBER 1100nnnn (CnH) 0ppppppp n = 0 - 15 CHANNEL NUMBER p = 0 - 127 (3-1-5) CHANNEL AFTER TOUCH STATUS VALUE 1101nnnn (DnH) 0vvvvvvv n = 0 - 15 CHANNEL NUMBER v = 0 - 127 AFTER TOUCH VALUE (3-1-6) PITCH BEND CHANGE STATUS 1110nnnn (EnH) LSB 0vvvvvvv MSB 0vvvvvvv Transmitted with a resolution of 7 bits. n = 0 - 15 CHANNEL NUMBER PITCH BEND CHANGE LSB PITCH BEND CHANGE MSB (3-2) CHANNEL MODE MESSAGES STATUS CONTROL NUMBER CONTROL VALUE 1011nnnn (BnH) 0ccccccc 0vvvvvvv n = 0 - 15 CHANNEL NUMBER c = CONTROL NUMBER v = DATA VALUE (3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0) All the sounds currently played including the channel messages such as note-on and hold-on in a certain channel are muted when receiving this message. (3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0) Resets the values set for the following controllers. PITCH BEND CHANGE 0 (center) CHANNEL AFTER TOUCH 0 (minimum) MODULATION 0 (minimum) EXPRESSION 127 (maximum) BREATH CONTROLLER 127 (maximum) FOOT CONTROLLER 127 (maximum) Assign 1 0 (center) Assign 2 0 (center) SUSTAIN SWITCH 0 (off) SOSTENUTO SWITCH 0 (off) RPN Not assigned; No change Doesn't reset the following data: PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL, RELEASE TIME, ATTACK TIME,DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3,PORTAMENTO SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING (3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0) All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or Sostenuto is on, notes will continue sounding until these are turned off. (3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1. (3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. Sets VOICE RECEIVE CHANNEL to "OMNI ON." (3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0...16) Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the channel will be Mode 4 (m = 1). In the Voice mode, the mode can be Mode 2 (m = 1) according to VOICE RECEIVE CHANNEL. (3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0) Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode 3. In the Voice mode, the mode can be Mode 1 according to VOICE RECEIVE CHANNEL. (3-3) REGISTERED PARAMETER NUMBER STATUS LSB RPN LSB 1011nnnn (BnH) 01100100 (64H) 0ppppppp n = 0 - 15 CHANNEL NUMBER p = RPN LSB (Refer to the table as shown below.) MSB RPN MSB 01100101 (65H) 0qqqqqqq q = RPN MSB (Refer to the table as shown below.) DATA ENTRY MSB DATA VALUE DATA ENTRY LSB DATA VALUE 00000110 (06H) 0mmmmmmm 00100110 (26H) 0lllllll m = Data Value l = Data Value First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB. RPN D.ENTRY LSB MSB MSB LSB 00H 00H mmH --- 01H 00H mmH llH 02H 00H mmH --7FH 7FH --- --- PARAMETER NAME DATA RANGE PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones) MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH} (-8192*100/8192) - 0 - (+8192*100/8192) MASTER COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones) RPN RESET RPN numbers will be left not designated. The internal values are not affected. (3-4) SYSTEM REAL TIME MESSAGES (3-4-1) ACTIVE SENSING STATUS 11111110 (FEH) Transmitted at every 200 msec. Once this code is received, the instrument starts sensing. When no status nor data is received for over approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played is forcibly turned off. (3-5) SYSTEM EXCLUSIVE MESSAGE (3-5-1) UNIVERSAL NON REALTIME MESSAGE (3-5-1-1) GENERAL MIDI MODE ON F0H 7EH 7FH 09H 01H F7H Received in the Multi mode when Compare or Store Compare is inactive. (3-5-1-2) IDENTITY REQUEST (Receive only) F0H 7EH 0nH 06H 01H F7H ("n" = Device No. However, this instrument receives under "omni.") (3-5-1-3) IDENTITY REPLY (Transmit only) F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H dd: Device family number/code S90 XS: 3CH 06H S70 XS: 3DH 06H mm : version mm = (version no. - 1.0)) * 10 e.g.) version 1.0 mm = (1.0 - 1.0) * 10 = 0 version 1.5 mm = (1.5 - 1.0) * 10 = 5 (3-5-2) UNIVERSAL REALTIME MESSAGE (3-5-2-1) MIDI MASTER VOLUME F0H 7FH 7FH 04H 01H llH mmH F7H Sets the MASTER VOLUME value. The value "mm" is used to set the master volume (the value "ll" should be ignored). (3-5-3) PARAMETER CHANGE (3-5-3-1) NATIVE PARAMETER CHANGE, MODE CHANGE 11110000 01000011 0001nnnn 01111111 00001101 0aaaaaaa 0aaaaaaa 0aaaaaaa 0ddddddd | 11110111 F0 43 1n 7F 0D aaaaaaa aaaaaaa aaaaaaa ddddddd | F7 Exclusive status YAMAHA ID device Number Model ID Model ID Address High Address Mid Address Low Data End of Exclusive For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted. See the following MIDI Data Table for Address. (3-5-4) BULK DUMP 11110000 01000011 0000nnnn 01111111 00001101 0bbbbbbb 0bbbbbbb 0aaaaaaa 0aaaaaaa 0aaaaaaa 0 | 0ccccccc 11110111 F0 43 0n 7F 0D bbbbbbb bbbbbbb aaaaaaa aaaaaaa aaaaaaa 0 | ccccccc F7 Exclusive status YAMAHA ID device Number Model ID Model ID Byte Count Byte Count Address High Address Mid Address Low Data Check-sum End of Exclusive See the following MIDI Data Table for Address and Byte Count. The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data and Check sum itself are added. (3-5-5) DUMP REQUEST 11110000 01000011 0010nnnn 01111111 00001101 0aaaaaaa 0aaaaaaa 0aaaaaaa 11110111 F0 43 2n 7F 0D aaaaaaa aaaaaaa aaaaaaa F7 Exclusive status YAMAHA ID device Number Model ID Model ID Address High Address Mid Address Low End of Exclusive See the following MIDI Data Table for Address and Byte Count. (3-5-6) PARAMETER REQUEST 11110000 01000011 0011nnnn 01111111 00001101 0aaaaaaa 0aaaaaaa 0aaaaaaa 11110111 F0 43 3n 7F 0D aaaaaaa aaaaaaa aaaaaaa F7 Exclusive status YAMAHA ID device Number Model ID Model ID Address High Address Mid Address Low End of Exclusive See the following MIDI Data Table for Address. 100 S90 XS/S70 XS Data List