Yamaha SY85 Midi Data Format (image) - Page 2

Bn 00 xx 20 xx

Card2 Voice(multi)

Card3 Voice(multi)

Card4 Voice(multi)

Internal1 Perf(multi)

Internal2 Perf(multi)

Card1 Perf(multi)

Card2 Perf(multi)

Data

00,36

00,39

00,42

00,80

00,83

00,81

00,84

When the mode is set to off the program change is not transmitted.

When the mode is set to table, the conversion format contained in the program transmission table is

applied and transmitted.

1.2.1.5 Program change

Program change is transmitted, when a voice is selected in voice mode, when a performance is

selected in performance mode.

Program change No. is assigned as shown below in accordance with the mode.

1.2.2.3 Program change

When a program change message is received, the SY85 performs the following operations.

Three types of reception modes can be set with the system setup.

1)off:

Program change is not received.

2)normal:

In each play mode, the program No. changes in accordance with 00 ～ 63 of the current

mode.

The program bank change is not received.

3) direct:

In voice mode, voice A1 ～ H8 correspond to the program change data 00 ～ 63.

INT1,

INT2 and CARD change in accordance with the program bank change.

Program change data 64 ～ 127 is not received. In performance mode, performance A1 ～

H8 correspond to program change data 00 ～

63. Int1, Int2, and CARD change in accor

dance with the program bank change.

Program change data 64 ～ 127 are not received.

In Multi mode, each INST program changes in accordance with the above.

Refer to during transmission for the bank change.

4) table:

Reception applies to 3) direct.

Transmission is carried out in accordance with the PROGRAM CHANGE TABLE.

1.2.2.4 Pitch bend

Pitch bend is received only on the MSB side.

1.2.2.5 After touch

After touch is received in accordance with the reception channel of each mode.

1.2.2.6 Channel mode message

2

Data

Voice

Internal1

0～63

00～63

Internal2

0～63

00～63

Internal3

0～63

00～63

Internal4

0～63

00～63

Card1

0～63

00～63

Card2

0～63

00～63

Card3

0～63

00～63

Card4

0～63

00～63

Performance

Internal1

0～63

00～63

Internal2

0～63

00～63

Card1

0～63

00～63

Card2

0～63

00～63

When the mode is set to off the program change is not transmitted.

When the mode is set to table, the conversion format contained in the program transmission table is

applied and transmitted.

1.2.1.6 Pitch bend

Pitch bend is transmitted with a resolution of 7 bits.

1.2.1.7 After touch

After touch is output when it is operated.

1.2.1.8 Channel mode message

Channel mode message is not transmitted.

1.2.2

Reception

1.2.2.1 Note Off

Reception note range

= C-2 ～ G8

Velocity range

= not received.

1.2.2.1 Note On/Off

Reception note range

= C-2 ～ G8

Velocity range

= 0 ～ 127

1.2.2.2 Control change

The parameters in the table below can be controlled by MIDI.

cntrl#

parameter

data rng

1

Modulation wheel

0 ～ 127

4

Foot control

0 ～ 127

7

Foot Volume

0 ～ 127

10

Pan

0 ～ 127

0～119

Volume

0 ～ 127

1～120

Effect Param1

0 ～ 127

1～120

Effect Param2

0 ～ 127

16～19

CS Param

0 ～ 127

64

Sustain Switch

0 ,

127

Pan is received only when MULTI is generated.

cntrl#

parameter

data rng

120

All Sound Off

0

121

Reset All Controller

0

123

All Notes Off

0

1.2.3 Configuration of keyboard section and tone generator

KBD

transmit ch

→ MIDI OUT

omni

(voice)

or rcv ch (multi)

voice rcv ch

(voice)

or rcv ch (multi)

TONE GENERATOR

○

○

local on/off

MIDI IN →

Note 1)

In voice mode, sound is generated even if the Voice receive channel and the Keyboard Trans.

channel do not match.

Note 2)

Note On from the keyboard and Note On from MIDI are distinguished.

Controller information

from the keyboard and controller information from the MIDI (control change, after touch, pitch

bend, etc.) are not distinguished except for sustain switch.

Yamaha SY85 Midi Data Format (image) - Page 2

All Sound Off

Page 2 highlights