Yamaha YDP-151 Owner's Manual - Page 35

Securely tighten the screws on C that, were attached in Step 1-3., Mount A., Secure A.

Get Yamaha YDP-151 PDF manuals and user guides View all Yamaha YDP-151 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

33 ENGLISH R L R 2-5 Securely tighten the screws on the top of B that were attached in Step 2-2. E 2-2, 2-5 2-1 Place the bottom ends of the rear panel on each foot. B D 2-3 2-4 2-3 3. Securely tighten the screws on C that were attached in Step 1-3. 5. Secure A. 5-1 Adjust the position of A so that the left and right ends of A will project beyond D and E equally when seen from the front. 5-2 Secure A by tightening the short screws 2 (6 × 16mm) from the front. 5-1 Projection of A A 5-2 B C 3 4. Mount A. Be sure to place your hands at least 10 cm from either end of the main unit when positioning it. A At least 10 cm E B D 6. Connect the pedal cord. 6-1 Insert the pedal cord plug to the pedal connector from the rear. 6-2 Attach the cord holders to the rear panel as shown, then clip the cord into the holders. 6-3 Use a vinyl tie to take up any slack in the pedal cord. 6-1 PEDAL AC INLET 6-3 CAUTION • Fingers can become pinched between the main unit and the rear or side panels, be extra careful 6-2 so as not to drop the main unit. • Do not hold the keyboard in any position other than the position shown in the illustration. YDP-151/YDP-323 Keyboard Stand Assembly 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
YDP-151/YDP-323
Keyboard Stand Assembly
35
ENGLISH
2-5
Securely tighten the screws on the top of B
that were attached in Step 2-2.
3.
Securely tighten the screws on C that
were attached in Step 1-3.
4.
Mount A.
CAUTION
•
Fingers can become pinched between the main
unit and the rear or side panels, be extra careful
so as not to drop the main unit.
•
Do not hold the keyboard in any position other
than the position shown in the illustration.
5.
Secure A.
5-1
Adjust the position of A so that the left and
right ends of A will project beyond D and E
equally when seen from the front.
5-2
Secure A by tightening the short screws
2
(6
×
16mm) from the front.
6.
Connect the pedal cord.
6-1
Insert the pedal cord plug to the pedal con-
nector from the rear.
6-2
Attach the cord holders to the rear panel as
shown, then clip the cord into the holders.
6-3
Use a vinyl tie to take up any slack in the
pedal cord.
R
L
2-2, 2-5
2-4
2-3
2-3
2-1
D
B
E
Place the bottom
ends of the rear
panel on each foot.
3
B
C
R
A
B
D
E
Be sure to place your hands at least
10 cm from either end of the main
unit when positioning it.
At least
10 cm
5-2
A
5-1
Projection
of A
AC INLET
PEDAL
6-1
6-3
6-2
33