Yamaha YP-700 YP-700 OWNERS MANUAL

Yamaha YP-700 Manual

Get Yamaha YP-700 PDF manuals and user guides View all Yamaha YP-700 manuals
Add to My Manuals
Save this manual to your list of manuals

Yamaha YP-700 manual content summary:

  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 1
    0 YAMAHA YAMAHA STEREO SYSTEMS -STEREO TURNTABLE F.• to CENTER
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 2
    .`• FEATURES TOP PANEL MECHANISM ASSEMBLY ADJUSTMENT COMPONENT PARTS CONFIGURATION OPERATION REPLACEMENT CARTRIDGE INSTALLATION MAINTENANCE & ACCESSORIES MALFUNCTIONS & SOLUTIONS SPECIFICATIONS • 1 2 3 5 7 8 9 11 12 13
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 3
    system, providing many carefree hours of listening enjoyment. Please read the following instructions carefully before operating the turntable. 6 -7 la% tOE'Cl ,12FEAtl). The YP-700 employs a professional type belt drive system, a superior method of providing constant speed control and reducing
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 4
    rM s Auto-return holding tape fib Red-topped transit holding screws (5) (3 Motor pulley (0 Cueing lever, oiled damped (re Cycle changeover switch (50 or 60 Hz) • Tonearm securing ribbon • Tonearm rest PLAY/OFF switch it Speed selector switch Lubrication hole fg1) Cartridge shell fastener (0 Tonearm
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 5
    to it) and slip the belt over the motor pulley, threading the belt through the speed change guide as you do so, Fig. 6. When the belt is in position, remove the ribbon, put the rubber sheet on the platter and snap the triangular pulley assembly cover into place. TURNTABLE PLATTER 33RPM -•Z Fig
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 6
    tone arm weight from the accessory box and screw it onto the end of the arm (Fig. 7) q I jl Fig. 7 8. Pkig in the power cord. The turntable platter may shift slightly as the gears of the mechanism align themselves
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 7
    in or out until the tone arm is in a freely balanced position (parallel with turntable base, Fig. 9 ). When the tone arm is balanced, return it to the pressure of two grams, which is the correct stylus pressure for the Yamaha cartridge. If a different cartridge is used, stylus pressure adjustment is
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 8
    cause the stylus to skip or drag on the record, producing an un-natural sound. If the supporting surface is not steady, it will cause the stylus to skip with each vibration. 2. When the YP-700 is placed close to an amplifier it may pick up induced hum from the amp. Increasing the
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 9
    ? Did you follow the assembly instructions completely during set-up? If the with the drive belt over the pulley and through the change-over guide? If the turntable connected to the L and R inputs of the amplifier? If not, there may be distortion in the output and reversal of channels. III YP-700
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 10
    this point. In this case, press the PLAY/OFF switch and then place the tonearm manually at the desired position. (B) When the record finishes, the tonearm will automatically lift and return to its rest position and the turntable will stop. * At the end of the record the auto-return may not function
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 11
    Yamaha dealer. The MM (moving magnet), IM (induced magnet) and MC (moving coil) type cartridges can be used with the YP-700 , always consult the cartridge manufactuers instructions before installation. L.-18km) 0 84 high (Fig. 20), it will strike the turntable dust cover when the arm lifts. Such a
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 12
    weight according to the tone arm balance procedures on page 5. 17mm Overhang Turntable Quite -seat Fig. 21 Included in the accessory kit are two subweights, sufficient to achieve a balanced condition. The subweights are NOT required when Yamaha cartridge CG-7000 is used. As shown in Fig. 22 the
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 13
    hole under the turntable. No other lubrication is necessary; all other moving parts are self-lubricating. * If any oil spills on the belt or connected parts, with a Yamaha stylus, Model N-7000. ' 10 tautzaillow k 11 " Fig. 24 Follow the assembly procedures in reverse order. Store the turntable (and
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 14
    and metal fittings. Re-thread the drive belt through the change-over guided. Play a standard size record.lf problem remains, insure shipping tape removed from auto-return mechanism. If tape has been removed, refer to your Yamaha dealer for adjustment. If problem occurs only on one record, than
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 15
    brush. Replace stylus. Replace record, clean record. Adjust stylus pressure. • _• ..... . . . TURNTABLE Type: Motor: Turntable Platter: Wow & Flutter: S/N Ratio: TONE ARM Type: Stylus pressure: Head shell: 2-Speed (33.1/3 & 45 rpm), Belt drive Synchronous outer rotor type motor 30 cm in dia
  • Yamaha YP-700 | YP-700 OWNERS MANUAL - Page 16
    nM IEI tl III ail IE ki 'E 161 ' l'EE'YW" 1"Eil n 'EEi'" E• IEEENEE; n 1EI ;IIIEE'EE ; ;E• ,J1 NIPPON GAKKI CO., LTD. HAMAMATSU JAPAN AOM-1 3610 H.S 10) 2 Printed in Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
0
YAMAHA
YAMAHA
STEREO
SYSTEMS
F.•
to
-STEREO
TURNTABLE
CENTER