Zanussi Z716WT83BI User Manual
Zanussi Z716WT83BI Manual
 |
View all Zanussi Z716WT83BI manuals
Add to My Manuals
Save this manual to your list of manuals |
Zanussi Z716WT83BI manual content summary:
- Zanussi Z716WT83BI | User Manual - Page 1
User Manual GETTING STARTED? EASY. Z716WT83BI EN User Manual Washer Dryer - Zanussi Z716WT83BI | User Manual - Page 2
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. • Children between 3 and 8 years of age and persons with very - Zanussi Z716WT83BI | User Manual - Page 3
load of 7 kg (refer to the "Programme chart" chapter). • The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. • Old hose sets must not be reused. • If the mains power supply cable is damaged, it must - Zanussi Z716WT83BI | User Manual - Page 4
, should only be used as specified by the product manufacturer's instructions. • Remove all objects from items that could be a source of fire ignition such as lighters or matches. • Never stop the washer dryer before the end of the drying cycle unless all items are quickly removed and separated so - Zanussi Z716WT83BI | User Manual - Page 5
washer dryer. Follow the cleaning instruction on the item label. • Plastic items are not heat resistant. - If a detergent ball is used, remove it before starting a drying programme. - Do not use appliance. SERVICE • To repair the appliance contact an Authorised Service Centre. • Use original spare - Zanussi Z716WT83BI | User Manual - Page 6
by two persons. THE APPLIANCE IS EQUIPPED WITH ... A BC DE x4 x2 x1 x1 x1 F G H L x1 x2 x1 x1 x1 x2 UNPACKING WARNING! Use the gloves. WARNING! Remove all the packaging and the transit bolts before installing the appliance. 1. Put two polystyrene packaging elements on the floor - Zanussi Z716WT83BI | User Manual - Page 7
hose. This is due to the testing with water of the appliance in factory. 6. Remove the three bolts, the hose holders and plastic spacers by using the spanner supplied with the appliance. 7 - Zanussi Z716WT83BI | User Manual - Page 8
7. Close the holes with the plastic caps you find in the user manual bag. Put the smallest cap F in upper hole and the two bigger caps G in low- F er holes. G We recommend that you keep the packaging and - Zanussi Z716WT83BI | User Manual - Page 9
HOSE AND CABLE CONNECTION 1020 mm 1100 mm 1450 mm 760 mm max 1000 mm min. 600 mm min. 600 mm max 1000 mm 900 mm The inlet hose 45O 20O 1360 mm 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the proper direction and with the proper inclination, check - Zanussi Z716WT83BI | User Manual - Page 10
with 3/4 thread. WARNING! Make sure that there are no leaks from the couplings. Use the hose supplied with appliance. Do not use an extension hose if the inlet hose is too short. Contact the Authorised Service Centre for an inlet hose replacement. Water drainage The drain hose can be connected - Zanussi Z716WT83BI | User Manual - Page 11
pipe in the room wall and L tighten it with the supplied cable tie L. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. BUILDING IN min.600 mm min. 560 mm min. 820 mm 16-22 mm This appliance - Zanussi Z716WT83BI | User Manual - Page 12
Before proceeding with appliance building in, bring it near the recess and preposition the inlet hose, the drain hose and the mains cable. WARNING! Make sure they are not kinked or squashed. INSTALLING ANTI-TILTING DEVICE If the height of the counter is 820 mm or lower, you cannot install the anti- - Zanussi Z716WT83BI | User Manual - Page 13
before the appliance is built in completely. If the cupboard door has to be opened from left to N right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. M O M N O Make sure that the plate with magnet is on the upper position. 13 - Zanussi Z716WT83BI | User Manual - Page 14
of the hole to countersink the upper hinge. The centre of the hole Y should be at the same height of the stroke on the hinge support. Set the position of the lower hole respecting dimensions and distances shown in the drawing (449 mm). Countersink the holes. Hinges To mount the hinges - Zanussi Z716WT83BI | User Manual - Page 15
Mounting the door Fix the hinges to the hinge supports on the appliance by means of the two supplied screws B. The hinges can be the mark as described in the first step. 10 11 12 1 Hinge supports 2 Detergent dispenser 3 Control panel 4 5 6 7 8 9 4 Magnetic plate 5 Door handle 6 Rating plate 13 15 - Zanussi Z716WT83BI | User Manual - Page 16
and permanent Child Lock option 8 Prewash touch button and permanent Extra Rinse option 9 Spin touch button 10 Temp. touch button 11 Mode touch button: • Mode - Wash • Mode - Dry 12 On/Off push button 16 - Zanussi Z716WT83BI | User Manual - Page 17
The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. ). • Cycle end ( ). • Warning code (e.g. ). • Error indicator ( ). Flextime indicator. , washing and/or drying phase). Extra Rinse indicator. The spin area: Spin speed indicator No Spin indicator. Spin phase - Zanussi Z716WT83BI | User Manual - Page 18
-by paragraph in Daily Use chapter. MODE Thanks to this button, a cycle can perform: • Only washing: Mode - Wash indicator is on (default mode). • Washing and drying: Mode - Wash and Mode - Dry after you switch it off or change/reset the programme. This option increases the programme duration. 18 - Zanussi Z716WT83BI | User Manual - Page 19
degree of soiling. When you set a washing programme, the display shows the default duration soiled garments. a quick cycle for a full load of lightly soiled garments. very quick cycle for a this option after you switch it off or change/reset the programme. If you press any button, the indicator - Zanussi Z716WT83BI | User Manual - Page 20
range Maximum load Programme description (Type of load and soil level) Washing programmes Cottons 40 °C 90 °C - Cold 1600 rpm (1600400 rpm for rinsing and spinning the laundry. The default spin speed is the one used for cotton programmes. Reduce the spin speed accordingly to the type of laundry - Zanussi Z716WT83BI | User Manual - Page 21
of the detergent dispenser, put the flap of the compartment in upward position. Pour a cup of chlorine bleach or a washing machine cleaner in the washing phase compartment. DO NOT use both together. After the drum cleaning, run a further rinse cycle with empty drum and no detergent to remove any - Zanussi Z716WT83BI | User Manual - Page 22
30 °C 40 °C - 30 °C 1200 rpm 1 kg Mixed fabrics (cotton and synthetic items). Complete short programme to wash and dry laundry loads up to 1 kg in one go. It only lasts 1 hour. Reset position. The display shows dashes only. 1) Cottons energy saving programme. This programme at 60ºC with a load - Zanussi Z716WT83BI | User Manual - Page 23
Spin No Spin Prewash Flextime Delay Start Programme Machine Clean Daily Wash Sportswear ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Outdoor ■ ■ ■ ■ ■ Denim ■ ■ ■ ■ ■ NonStop 60min ■ 1) If you set the No Spin option, the appliance performs draining only. AUTOMATIC DRYING Dryness - Zanussi Z716WT83BI | User Manual - Page 24
Dryness Level Type of fabric Load 1) Cupboard Dry2) For items to be stored Cottons and Linen (bathrobes, bath towels, etc) Synthetics and mixed fabrics (jumpers, blouses, underwear, household and bed linen) up to 4 kg up to 3 kg Delicate fabrics (acrylics, viscose and delicate mixed fabrics) - Zanussi Z716WT83BI | User Manual - Page 25
is completed (sequence of sounds for about 2 minutes). • The appliance has a malfunction (sequence of short sounds for about 5 minutes). BEFORE FIRST USE To activate/deactivate the acoustic signals when the programme is completed, touch the Mode and the Temp. buttons simultaneously for about - Zanussi Z716WT83BI | User Manual - Page 26
at the highest temperature without any laundry in the drum. DAILY USE - WASHING ONLY WARNING! Refer to Safety chapters. This removes all possible the laundry. Washing heavily oiled, greasy stains could cause damage to rubber parts of the washing machine. Always follow the instructions that you find - Zanussi Z716WT83BI | User Manual - Page 27
down. With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not exceed to liquid detergent PROGRAMME 1. Turn the programme dial to select the desired washing programme. The indicator of Mode - Wash button illuminates. The indicator of the Start/Pause button - Zanussi Z716WT83BI | User Manual - Page 28
the new programme. There is also an alternative way of cancelling: 1. Rotate the selector knob to the "Reset" position . 2. Wait for 1 second. The display shows . Now, you can set a new washing programme. OPENING THE DOOR - ADDING GARMENTS If the temperature and level of the water in the drum - Zanussi Z716WT83BI | User Manual - Page 29
drain the water to open the door: DAILY USE - WASHING & DRYING 1. If necessary, touch the Spin new cycle. If the dial is rotated to the "Reset" position , the appliance automatically turns off in 30 seconds appliance is an automatic washer dryer. COMPLETE WASH&DRY PROGRAMME Automatic Non-Stop - Zanussi Z716WT83BI | User Manual - Page 30
, the appliance does not let you set a too low spin speed for the items to be washed and dried. DAILY USE - DRYING ONLY 2. Touch button Start/Pause to start the programme. The AutoAdjust estimation starts. In . WARNING! Refer to Safety chapters. This appliance is an automatic washer dryer. 30 - Zanussi Z716WT83BI | User Manual - Page 31
The indicator of Mode - Dry button illuminates and the indicator of Mode - Wash button goes off. When drying a big amount of laundry, to have good the seal and the inside of the door with a wet cloth. During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could - Zanussi Z716WT83BI | User Manual - Page 32
a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ). • A very small load can cause balance problems with the spin phase leading to excessive vibration. If this occurs: a. interrupt the programme and open the door (refer to "Daily Use" chapter); b. manually - Zanussi Z716WT83BI | User Manual - Page 33
end of the drying cycle: 1. Use fabric conditioner in the washing cycle. 2. Use special fabric conditioner for tumble dryers. When the drying programme is Always follow the instructions that you find on the packaging of the product. MAINTENANCE WASH The repeated and prolonged use of low temperature - Zanussi Z716WT83BI | User Manual - Page 34
body in the washing or tap water containing iron Clean the drum with special products for stainless steel. Always follow the instructions that you find of the recess. Use a small brush to clean the recess. 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing - Zanussi Z716WT83BI | User Manual - Page 35
without any clothes in the drum. CLEANING THE DRAIN PUMP WARNING! Disconnect the mains plug from the mains socket. Proceed as follows to clean the pump: Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The - Zanussi Z716WT83BI | User Manual - Page 36
fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre. 8. Clean the filter under the water tap. 36 - Zanussi Z716WT83BI | User Manual - Page 37
special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 1 2 1 10. Close the pump cover. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment - Zanussi Z716WT83BI | User Manual - Page 38
litres of water in the main wash compartment of the detergent dispenser. 2. the inlet hose and the drain pump. TROUBLESHOOTING 1. Disconnect the mains plug from the mains 0 °C before you use the appliance again. The problem (refer to the table). If the problem persists, contact the Authorised Service - Zanussi Z716WT83BI | User Manual - Page 39
is in the correct position. The hose may be positioned too low. Refer to "Installation instruction". • Make sure that the sink spigot is not clogged. • Make sure that the "Care and cleaning". • Adjust manually the items in the tub and start the spin phase again. This problem may be caused by balance - Zanussi Z716WT83BI | User Manual - Page 40
electrical power. • This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre. If you need to open the door, please read carefully "Emergency door opening". • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure - Zanussi Z716WT83BI | User Manual - Page 41
alarm codes, deactivate and activate the appliance. If the problem continues, contact the Authorised Service Centre. EMERGENCY DOOR OPENING In case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door - Zanussi Z716WT83BI | User Manual - Page 42
Minimum Maximum 596 mm/ 819 mm/ 540 mm/ 553 mm 230-240 V 2000 W 13 A 50 Hz IPX4 Cold water 0.5 bar (0.05 MPa) 8 bar (0.8 MPa) Maximum wash load Cotton 7 kg Maximum dry load Cotton 4 kg Synthetics 3 kg Spin Speed Maximum spin speed 1550 rpm 1) Connect the water inlet hose to a water tap - Zanussi Z716WT83BI | User Manual - Page 43
43 - Zanussi Z716WT83BI | User Manual - Page 44
157018090-C-292018 WWW.ZANUSSI.COM/SHOP
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
GETTING
STARTED?
EASY.
User Manual
Z716WT83BI
EN
User Manual
Washer Dryer