Zanussi ZWT71401WA Product Manaul

Zanussi ZWT71401WA Manual

Get Zanussi ZWT71401WA PDF manuals and user guides View all Zanussi ZWT71401WA manuals
Add to My Manuals
Save this manual to your list of manuals

Zanussi ZWT71401WA manual content summary:

  • Zanussi ZWT71401WA | Product Manaul - Page 1
    EN User manual Washer Dryer ZWT 71401 WA
  • Zanussi ZWT71401WA | Product Manaul - Page 2
    change without notice. Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. Children and
  • Zanussi ZWT71401WA | Product Manaul - Page 3
    it is exposed to the weather. • Obey the installation instruction supplied with the appliance. • Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean. • Do not install the appliance where the appliance door can not be fully opened. • Always be careful
  • Zanussi ZWT71401WA | Product Manaul - Page 4
    have been left in the pockets of the clothing. • Only dry fabrics which are applicable to dry in the tumble dryer. Follow the instructions on the fabric label. • Do not dry not washed items in the appliance. • If you have washed your laundry with a stain remover start an extra rinse cycle before
  • Zanussi ZWT71401WA | Product Manaul - Page 5
    Service to repair the appliance. We recommend only the use of original spare parts. beginning of the wash programme. The stain remover is added during detergent used for main wash. If using liquid detergent poured into the compartment before starting the wash programme. Child Safety device Make sure
  • Zanussi ZWT71401WA | Product Manaul - Page 6
    by relevant numbers on the following pages. 1 23 456 7 8 1 Programme selector dial 2 SPIN reduction button 3 OPTION button 4 EXTRA RINSE button 5 DRYING TIME button 6 10 9 6 EASY IRON button 7 START/PAUSE button 8 DELAY START button 9 DOOR LOCKED pilot light 10 Display www.zanussi.com
  • Zanussi ZWT71401WA | Product Manaul - Page 7
    drying time increases by 5 mins. Easy Iron By selecting this option the laundry is gently washed and spun to avoid any creasing. In this way ironing is easier. Furthermore the machine will perform some additional rinses in some programmes. On cotton programmes the maximum spin The machine is working
  • Zanussi ZWT71401WA | Product Manaul - Page 8
    the event of operating problems, some alarm codes can be displayed, for example (see paragraph «What to do if...»). • Incorrect option selection If an option which is not compatible with the set wash programme is selected, the message Err is displayed at the bottom of the display for a few seconds
  • Zanussi ZWT71401WA | Product Manaul - Page 9
    cotton (normally soiled items). 6-7-8 90°-40° Prewash - Main wash - Rinses Long spin at maximum speed Max. load 7 kg - Reduced load 3 SPIN RINSE HOLD ECO2) SUPER QUICK EXTRA RINSE EASY IRON RINSE HOLD SUPER QUICK EXTRA RINSE SPIN RINSE HOLD EASY IRON Delicates Detergent Compartment 3) www.zanussi
  • Zanussi ZWT71401WA | Product Manaul - Page 10
    fabrics with «hand washing» care symbol and machine washable wollens. 20-Cottons Drying programme for cotton items 21-Synthetics Drying programme for synthetic items 22-Rinses Rinses Long spin at maximum speed Max liquid detergents, a programme without PREWASH must be selected. 10 www.zanussi.com
  • Zanussi ZWT71401WA | Product Manaul - Page 11
    Label must be tested dividing the maximum washing load by two equal parts and drying with DRYING TIME each of them. Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer's washing instructions. Sort the laundry as follows: whites
  • Zanussi ZWT71401WA | Product Manaul - Page 12
    suggest you to add a water softener following always the manufacturer's instructions. When the degree of hardness is soft, readjust the quantity of the detergent. Preparing the drying cycle As a dryer, the appliance works on the condensation principle. Therefore, the water tap must be open and the
  • Zanussi ZWT71401WA | Product Manaul - Page 13
    unattended so you do not need to worry that children might be injured by or cause damage to the appliance. This function remains enabled also when the washing machine is not working. There are two different ways to set this option: 1. Before pressing button 7: it will be impossible to start the
  • Zanussi ZWT71401WA | Product Manaul - Page 14
    the messageErr is displayed to indicate a wrong selection. The machine will not perform the new selected programme. Select the spin speed by pressing button 2 When selecting a programme, the appliance proposes automatically the maximum spin speed provided for that programme. (See "Washing programmes
  • Zanussi ZWT71401WA | Product Manaul - Page 15
    started the programme: 1. Set the washing machine to PAUSE by pressing button 7. 2. Press button 8 once. On the display will appear '. 3. Press button change, you must pause the washing machine by pressing button 7. Changing a running programme is possible only by resetting it. Turn the programme
  • Zanussi ZWT71401WA | Product Manaul - Page 16
    programme The machine stops automatically. The blinking appears on the display, the pilot light of but- ton 7 and the pilot light 9 go off. Use - Drying If a instructions to empty out the water: 1. Turn the programme selector dial to . 2. Select the draining or spinning programme. 3. Reduce the spin
  • Zanussi ZWT71401WA | Product Manaul - Page 17
    softener. 2. Switch the machine on by turning the selector dial to the set washing programme/ fabric. 3. Select the required options by pressing the relevant buttons. If possible, do not select a spin speed lower than that proposed by the appliance to avoid too long a drying time therefore saving
  • Zanussi ZWT71401WA | Product Manaul - Page 18
    in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits. External cleaning Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly
  • Zanussi ZWT71401WA | Product Manaul - Page 19
    water inlet filters Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if wash cycle, always wait until the appliance has finished the cycle, and is empty. When refitting the pump cover, ensure it is securely re- www.zanussi
  • Zanussi ZWT71401WA | Product Manaul - Page 20
    the ECO Valve device avoiding that part of the detergent remains unused at next washing. Certain problems are due to lack of codes appears on the display and some acoustic signals sound every 20 seconds to indicate that the machine is not working: • : problem with the water supply. • : problem
  • Zanussi ZWT71401WA | Product Manaul - Page 21
    Problem The machine does not start: The machine does not fill: The machine does not empty and/or does not spin: Possible cause/Solution The door has not been closed. • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no
  • Zanussi ZWT71401WA | Product Manaul - Page 22
    washing cycle. The door lock has not been released. • Wait until the pilot light 9 goes off. There is water in the drum. • Select drain or spin programme to empty out the water. The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet
  • Zanussi ZWT71401WA | Product Manaul - Page 23
    problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mod Prod. No Ser. No ProMdo.d.N..o.. ... ... ... ... . . Ser. No Technical data Dimensions www.zanussi
  • Zanussi ZWT71401WA | Product Manaul - Page 24
    the inlet water temperature and on the ambient temperature. Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 24 www.zanussi.com
  • Zanussi ZWT71401WA | Product Manaul - Page 25
    the power supply cable and the hose from the hose holders on the rear of the appliance. Level the washing machine instruction booklet. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine
  • Zanussi ZWT71401WA | Product Manaul - Page 26
    the hose from your previous appliance to connect to water supply. The inlet hose is supplied with the appliance and can be found inside the machine drum. 35° 45° Warning! Installation should comply with local water (35.4'') and no less than 60 cm (23.6'') above floor level. 26 www.zanussi.com
  • Zanussi ZWT71401WA | Product Manaul - Page 27
    drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter WASHING MACHINE DISHWASHER SURFACE WATER DRAINS & SEWERS UNTREATED DISCHARGE RIVER FOUL DRAIN FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHARGE RIVER www.zanussi
  • Zanussi ZWT71401WA | Product Manaul - Page 28
    machine is originally prearranged for the assembly of a door opening from right to left. In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B). 35 Ø 12,5-14 depth 16-22 B C 416 When installing the appliance
  • Zanussi ZWT71401WA | Product Manaul - Page 29
    the hole depends on the adjacent furniture's dimensions. The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance. • c) Mounting the door Fix the hinges (1) to the machine by means of the M 5x15 screws
  • Zanussi ZWT71401WA | Product Manaul - Page 30
    Fig. H). With the appliance installed adjust all four feet ensuring the machine is stable, and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop. A final check for stability should be carried out with the machine on spin with a load, this will
  • Zanussi ZWT71401WA | Product Manaul - Page 31
    appliance power supply cable need to be replaced, this MUST be carried out by a Service Centre. The power supply cable must be easily accessible after installing the machine washed without prewashing in order to save detergent, water and time (the environment is protected too!). • The machine works
  • Zanussi ZWT71401WA | Product Manaul - Page 32
    132929821-A-502012 www.zanussi.com/shop
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
EN
User manual
Washer Dryer
ZWT 71401 WA