ZyXEL ES-315 User Guide

ZyXEL ES-315 Manual

ZyXEL ES-315 manual content summary:

  • ZyXEL ES-315 | User Guide - Page 1
    ES-315 ES-315-F Intelligent Layer 2 Managed Switch User's Guide Version 3.70 8/2007 Edition 1 DEFAULT LOGIN IP Address http://192.168.1.1 User Name admin Password 1234 www.zyxel.com
  • ZyXEL ES-315 | User Guide - Page 2
  • ZyXEL ES-315 | User Guide - Page 3
    , questions or suggestions for improvement to the following address, or use e-mail instead. Thank you! The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan. E-mail: [email protected] ES-315/ES-315-F User's Guide 3
  • ZyXEL ES-315 | User Guide - Page 4
    things you may need to configure or helpful tips) or recommendations. Syntax Conventions • The ES-315 and ES-315-F may be referred to as the "Switch", the "device", the "system" or the "product" in this User's Guide. • Product labels, screen names, field labels and field choices are all in bold
  • ZyXEL ES-315 | User Guide - Page 5
    Document Conventions Icons Used in Figures Figures in this User's Guide may use the following generic icons. The Switch icon is not an exact representation of your device. The Switch Computer Notebook computer Server DSLAM Firewall Telephone Router ES-315/ES-315-F User's Guide 5
  • ZyXEL ES-315 | User Guide - Page 6
    stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for type. Dispose of used batteries according to the instructions. Dispose them at the applicable collection point for ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 7
    Safety Warnings ES-315/ES-315-F User's Guide 7
  • ZyXEL ES-315 | User Guide - Page 8
    Safety Warnings 8 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 9
    Route ...87 Management ...91 Maintenance ...93 Access Control ...99 Diagnostic ...113 Syslog ...115 MAC Table ...119 ARP Table ...121 Troubleshooting and Product Specifications 125 Troubleshooting ...127 Product Specifications ...131 Appendices and Index ...137 ES-315/ES-315-F User's Guide 9
  • ZyXEL ES-315 | User Guide - Page 10
    Contents Overview 10 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 11
    Table of Contents Table of Contents About This User's Guide ...3 Document Conventions...4 Safety Warnings...6 Contents Overview ...9 Table of Contents...11 List of Introduction ...33 3.2 System Login ...33 3.3 The Status Screen ...34 3.3.1 Change Your Password 36 ES-315/ES-315-F User's Guide 11
  • ZyXEL ES-315 | User Guide - Page 12
    and Untagged Frames 57 7.2 Static VLAN ...58 7.2.1 Static VLAN Status ...58 7.2.2 Static VLAN Details 58 7.2.3 Configure a Static VLAN 59 7.2.4 Configure VLAN Port Settings 61 12 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 13
    78 13.5.2 MVR Modes ...78 13.5.3 How MVR Works ...78 13.6 General MVR Configuration 79 13.7 MVR Group Configuration 81 13.7.1 MVR Configuration Example 82 ES-315/ES-315-F User's Guide 13
  • ZyXEL ES-315 | User Guide - Page 14
    15.3 Save Configuration ...94 15.4 Reboot System ...94 15.5 Firmware Upgrade ...95 15.6 Restore a Configuration File 95 15.7 Backup Access Control Main Screen 99 16.3 About SNMP ...100 16.3.1 Supported MIBs 101 16.3.2 SNMP Traps ...101 16.3.3 Configuring SNMP 103 16 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 15
    ...109 16.9 Service Port Access Control 109 ARP Table 121 Part VI: Troubleshooting and Product Specifications 125 Chapter 21 Troubleshooting...127 21.1 Power, Hardware Instructions 134 Part VII: Appendices and Index 137 Appendix A IP Addresses and Subnetting 139 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 16
    Table of Contents Appendix B Common Services 149 Appendix C Legal Information 153 Appendix D Customer Support 157 Index...163 16 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 17
    36 Advanced Application > Multicast > Multicast Setting > MVR 80 Figure 37 Advanced Application > Multicast > Multicast Setting > MVR: Group Configuration 81 Figure 38 MVR Configuration Example 82 ES-315/ES-315-F User's Guide 17
  • ZyXEL ES-315 | User Guide - Page 18
    : Service Access Control 110 Figure 63 Access Control: Remote Management 111 Figure 64 Diagnostic ...113 Figure 65 Syslog ...116 Figure 66 Syslog: Server Setup ...117 Figure 67 MAC Table Flowchart ...119 Figure 68 MAC Table ...120 Figure 69 ARP Table ...122 Figure 70 Wall-mounting Example: ES-315
  • ZyXEL ES-315 | User Guide - Page 19
    IP Traps ...102 Table 35 SNMP Switch Traps ...103 Table 36 Access Control: SNMP ...103 Table 37 Access Control: Logins ...105 Table 38 Access Control: Service Access Control 110 ES-315/ES-315-F User's Guide 19
  • ZyXEL ES-315 | User Guide - Page 20
    ...122 Table 46 Hardware Specifications ...131 Table 47 Firmware Specifications ...131 Table 48 Feature Specifications ...132 Table 49 Standards Supported ...133 Table 50 IP Address Network Number and Host Subnet Planning 145 Table 61 Commonly Used Services ...149 20 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 21
    PART I Introduction and Hardware Getting to Know Your Switch (23) Hardware Overview (27) 21
  • ZyXEL ES-315 | User Guide - Page 22
    22
  • ZyXEL ES-315 | User Guide - Page 23
    4) and allowing them to communicate with one another and access the Internet through the Internet Service Provider's network switch (B). Figure 1 Internet Access through the Switch 1.1.2 IEEE 802.1Q VLAN For more information on VLANs, refer to Chapter 7 on page 57. ES-315/ES-315-F User's Guide 23
  • ZyXEL ES-315 | User Guide - Page 24
    This is recommended for everyday management of the Switch using a (supported) web browser. See Chapter 3 on page 33. • Command configure advanced features. See the Command Reference Guide. • FTP. Use FTP for firmware upgrades and configuration backup/restore. See Section ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 25
    . If you backed up an earlier configuration file, you would not have to totally re-configure the Switch. You could simply restore your last configuration. ES-315/ES-315-F User's Guide 25
  • ZyXEL ES-315 | User Guide - Page 26
    Chapter 1 Getting to Know Your Switch 26 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 27
    the front and rear panels of the switch. See your Quick Start Guide for information on making hardware connections. 2.1 LEDs The following figures show the front panels of the ES-315 and ES-315-F. Figure 3 Front Panel: ES-315 Figure 4 Front Panel: ES-315-F ES-315/ES-315-F User's Guide 27
  • ZyXEL ES-315 | User Guide - Page 28
    WAN port. Off There is no device connected to the WAN port. 2.2 Rear and Base Panels The following figures show the rear panels of the ES-315 and ES-315-F, and the base panel of the ES-315-F. Figure 5 Rear Panel: ES-315 Figure 6 Rear Panel: ES-315-F 28 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 29
    Figure 7 Base Panel: ES-315-F Chapter 2 Hardware Overview POWER ES-315/ES-315-F User's Guide 29
  • ZyXEL ES-315 | User Guide - Page 30
    Chapter 2 Hardware Overview 30 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 31
    PART II Basic Configuration The Web Configurator (33) Initial Setup Example (39) System Status and Port Statistics (43) Basic Setting (47) 31
  • ZyXEL ES-315 | User Guide - Page 32
    32
  • ZyXEL ES-315 | User Guide - Page 33
    windows from your device. Web pop-up blocking is enabled by default in Windows XP SP (Service Pack) 2. • JavaScript (enabled by default). • Java permissions (enabled by default). 3.2 System server nor manually entered a time and date in the General Setup screen. ES-315/ES-315-F User's Guide 33
  • ZyXEL ES-315 | User Guide - Page 34
    is turned off. C - Click this link to go to the status page of the Switch. D - Click this link to logout of the web configurator. 34 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 35
    Routing Maintenance Firmware Upgrade Restore Configuration Backup Configuration Load Factory Default Save Configuration Reboot System Access Control SNMP Logins Service Access to a screen where you can configure general identification information about the Switch. ES-315/ES-315-F User's Guide 35
  • ZyXEL ES-315 | User Guide - Page 36
    forward traffic by configuring the TCP/IP parameters manually. Management Maintenance This link takes you to screens where you can perform firmware and configuration file maintenance as well as reboot Access Control and then Logins to display the next screen. 36 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 37
    VLAN 1). 2 Filter all traffic to the CPU port. 3 Disable all ports. 4 Misconfigure the text configuration file. 5 Forget the password and/or IP address. 6 Prevent all services from accessing the Switch. 7 Change a service port number but forget it. ES-315/ES-315-F User's Guide 37
  • ZyXEL ES-315 | User Guide - Page 38
    of individual screens and some supplementary information. Click the Help link from a web configurator screen to view an online help description of that screen. 38 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 39
    static VLAN with fixed port members. In this example, you want to configure port 1 as a member of VLAN 2. Figure 12 Initial Setup Network Example: VLAN ES-315/ES-315-F User's Guide 39
  • ZyXEL ES-315 | User Guide - Page 40
    . In the example network, configure 2 as the port VID on port 1 so that any untagged frames received on that port get sent to VLAN 2. 40 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 41
    : Management IP Address 1 Connect your computer to any Ethernet port on the switch. Make sure your computer is in the same subnet as the switch. ES-315/ES-315-F User's Guide 41
  • ZyXEL ES-315 | User Guide - Page 42
    save your changes back to the run-time memory. Settings in the run-time memory are lost when the Switch's power is turned off. 42 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 43
    Setup screen. Link This field displays the speed (either 10M for 10Mbps or 100M for 100Mbps) and the duplex (F for full duplex or H for half). ES-315/ES-315-F User's Guide 43
  • ZyXEL ES-315 | User Guide - Page 44
    port statistics. Use this screen to check status and detailed performance data about an individual port on the Switch. Figure 16 Status > Port Details 44 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 45
    detailed information about packets received that were in error. RX CRC This field shows the number of packets received with CRC (Cyclic Redundant Check) error(s). ES-315/ES-315-F User's Guide 45
  • ZyXEL ES-315 | User Guide - Page 46
    octets in length. 10241518 This field shows the number of packets (including bad packets) received that were between 1024 and 1518 octets in length. 46 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 47
    General Setup screen also allows you to set the system time manually or get the current time and date from an external server when firmware including the date created. Ethernet Address This field refers to the Ethernet MAC (Media Access Control) address of the Switch. ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 48
    Time Server when Bootup Enter the time service protocol that your timeserver uses. Not all time servers support all protocols, so you may have to Time (RFC-868). None is the default value. Enter the time manually. Each time you turn on the Switch, the time and date will ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 49
    navigation panel to display the screen as shown. This screen allows you to set priority levels on the Switch. Refer to the chapter on VLAN. ES-315/ES-315-F User's Guide 49
  • ZyXEL ES-315 | User Guide - Page 50
    traffic types by inserting a tag into a MAC-layer frame that contains bits to define class of service. Frames without an explicit priority tag are given the default priority of the ingress port. Use the done configuring. Cancel Click Cancel to reset the fields. 50 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 51
    ports belonging to the pre-defined VLAN(s); 4 static VLAN addresses and 1 management VLAN address. " You must configure a VLAN first. Figure 20 Basic Setting > IP Setup ES-315/ES-315-F User's Guide 51
  • ZyXEL ES-315 | User Guide - Page 52
    mask. VID This field displays the ID number of the VLAN group. Default Gateway This field displays the IP address of the default gateway. 52 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 53
    . Note: Due to space limitation, the port name may be truncated in some web configurator screens. Type This field displays 10/100M for Ethernet connections. ES-315/ES-315-F User's Guide 53
  • ZyXEL ES-315 | User Guide - Page 54
    peer automatically to determine the connection speed and duplex mode. If the peer port does not support auto-negotiation or turns off this feature, the Switch determines the connection speed by detecting the signal Cancel to begin configuring this screen afresh. 54 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 55
    PART III Advanced VLAN (57) Static MAC Forward Setup (63) Filtering (65) Bandwidth Control (69) Broadcast Storm Control (67) Queuing Method (71) Multicast (73) 55
  • ZyXEL ES-315 | User Guide - Page 56
    56
  • ZyXEL ES-315 | User Guide - Page 57
    the system) is duplicated only on ports that are members of the VID (except the ingress port itself), thus confining the broadcast to a specific domain. ES-315/ES-315-F User's Guide 57
  • ZyXEL ES-315 | User Guide - Page 58
    Section 7.1 on page 57 for more information on static VLAN. Click on an index number in the VLAN Status screen to display VLAN details. 58 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 59
    for more information on static VLAN. To configure a static VLAN, click Static VLAN in the VLAN Status screen to display the screen as shown next. ES-315/ES-315-F User's Guide 59
  • ZyXEL ES-315 | User Guide - Page 60
    capable devices, the Normal status allows the port to join the VLAN dynamically. However, the Switch does not support GVRP. Select Fixed for the port to be a permanent member of this VLAN group. Select Forbidden if . Click Clear to start configuring the screen again. 60 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 61
    include this port in its member set. Clear this check box to disable ingress filtering. Enter a number between 1and 4094 as the port VLAN ID. ES-315/ES-315-F User's Guide 61
  • ZyXEL ES-315 | User Guide - Page 62
    panel to save your changes to the non-volatile memory when you are done configuring. Cancel Click Cancel to begin configuring this screen afresh. 62 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 63
    your network. 8.2 Configuring Static MAC Forwarding A static MAC address is an address that has been manually entered in the MAC address table. Static MAC addresses do not age out. When you set for identification purposes for this static MAC address forwarding rule. ES-315/ES-315-F User's Guide 63
  • ZyXEL ES-315 | User Guide - Page 64
    will be forwarded. Delete Click Delete to remove the selected entry from the summary table. Cancel Click Cancel to clear the Delete check boxes. 64 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 65
    address format, that is, six hexadecimal character pairs. Traffic to and from the specified MAC address is blocked. VID Type the VLAN group identification number. ES-315/ES-315-F User's Guide 65
  • ZyXEL ES-315 | User Guide - Page 66
    the rule(s) that you want to remove in the Delete column and then click the Delete button. Cancel Click Cancel to clear the selected checkbox(es) in the Delete column. 66 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 67
    broadcast Utilization Limit packets. Port This field displays the port number. Active Select the check box to enable traffic storm control on the relevant port. ES-315/ES-315-F User's Guide 67
  • ZyXEL ES-315 | User Guide - Page 68
    top navigation panel to save your changes to the non-volatile memory when you are done configuring. Cancel Click Cancel to reset the fields. 68 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 69
    Advanced Application > Bandwidth Control LABEL DESCRIPTION Active Select this check box to enable bandwidth control on the Switch. Port This field displays the port number. ES-315/ES-315-F User's Guide 69
  • ZyXEL ES-315 | User Guide - Page 70
    the top navigation panel to save your changes to the non-volatile memory when you are done configuring. Click Cancel to reset the fields. 70 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 71
    chapter introduces the queuing methods supported. 12.1 Queuing Method Overview bandwidth. 12.1.1 Strictly Priority Queuing Strictly Priority Queuing (SPQ) services queues based on priority only. As traffic comes into the Switch : 1 1+2+3+4 x 100 Mbps = 10 Mbps ES-315/ES-315-F User's Guide 71
  • ZyXEL ES-315 | User Guide - Page 72
    divided across the different traffic queues according to their weights. Queues with larger weights get more service than queues with smaller weights. Apply Click Apply to save your changes to the Switch's Click Cancel to begin configuring this screen afresh. 72 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 73
    can join. This allows you to control the distribution of multicast services (such as content information distribution) based on service plans and types of subscription. You can set the Switch to learn multicast groups without you having to manually configure them. ES-315/ES-315-F User's Guide 73
  • ZyXEL ES-315 | User Guide - Page 74
    Click Advanced Applications > Multicast > Multicast Setting link to display the screen as shown. See Section 13.1 on page 73 for more information on multicasting. 74 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 75
    and then make adjustments on a port-byport basis. Note: Changes in this row are copied to all the ports as soon as you make them. ES-315/ES-315-F User's Guide 75
  • ZyXEL ES-315 | User Guide - Page 76
    profile. A profile can be assigned to multiple ports. Click Advanced Applications > Multicast > Multicast Setting > IGMP Filtering Profile link to display the screen as shown. 76 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 77
    .5 MVR Overview Multicast VLAN Registration (MVR) is designed for applications (such as Media-on-Demand (MoD)) that use multicast traffic across an Ethernet ring-based service provider network. ES-315/ES-315-F User's Guide 77
  • ZyXEL ES-315 | User Guide - Page 78
    In compatible mode, the Switch does not send any IGMP reports. In this case, you must manually configure the forwarding settings on the multicast devices in the multicast VLAN. 13.5.3 How MVR Works can connect through a port configured as the receiver on the Switch. 78 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 79
    to 256 multicast rules on the Switch. " Your Switch automatically creates a static VLAN (with the same VID) when you create a multicast VLAN in this screen. ES-315/ES-315-F User's Guide 79
  • ZyXEL ES-315 | User Guide - Page 80
    . All source ports must belong to a single multicast VLAN. Select this option to set this port as a receiver port that only receives multicast traffic. 80 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 81
    multicast data sent to this multicast group. Configure MVR IP multicast group address(es) in the Group Configuration screen. Click Group Configuration in the MVR screen. Figure 37 Advanced Application > Multicast > Multicast Setting > MVR: Group Configuration ES-315/ES-315-F User's Guide 81
  • ZyXEL ES-315 | User Guide - Page 82
    Delete to remove the selected entry(ies) from the table. Cancel Select Cancel to clear the checkbox(es) in the table. 13.7.1 MVR Configuration Example The following figure shows a network example where ports 1, MVR screen and set the receiver and source ports. 82 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 83
    following figure shows an example where two multicast groups (News and Movie) are configured for the multicast VLAN 200. Figure 40 MVR Group Configuration Example ES-315/ES-315-F User's Guide 83
  • ZyXEL ES-315 | User Guide - Page 84
    Chapter 13 Multicast Figure 41 MVR Group Configuration Example 84 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 85
    PART IV IP Application Static Route (87) 85
  • ZyXEL ES-315 | User Guide - Page 86
    86
  • ZyXEL ES-315 | User Guide - Page 87
    N1 N2 Telnet SNMP R1 R2 14.2 Configuring Static Routing Click IP Application > Static Routing in the navigation panel to display the screen as shown. ES-315/ES-315-F User's Guide 87
  • ZyXEL ES-315 | User Guide - Page 88
    . Destination Address This field displays the IP network address of the final destination. Subnet Mask This field displays the subnet mask for this destination. 88 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 89
    transmission for routing purposes. Delete Click Delete to remove the selected entry from the summary table. Cancel Click Cancel to clear the Delete check boxes. ES-315/ES-315-F User's Guide 89
  • ZyXEL ES-315 | User Guide - Page 90
    Chapter 14 Static Route 90 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 91
    PART V Management Maintenance (93) Access Control (99) Diagnostic (113) Syslog (115) MAC Table (119) ARP Table (121) 91
  • ZyXEL ES-315 | User Guide - Page 92
    92
  • ZyXEL ES-315 | User Guide - Page 93
    Switch. At the time of writing, the Switch supports a single configuration. Firmware Upgrade Click Click Here to go to the Firmware Upgrade screen. Restore Click Click Here to go to in any screen to save your settings to the current configuration on the Switch. ES-315/ES-315-F User's Guide 93
  • ZyXEL ES-315 | User Guide - Page 94
    screen, click the Config 1 button next to Reboot System to reboot and load configuration one. The following screen displays. Figure 46 Reboot System: Confirmation 94 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 95
    see the System Info screen to verify your current firmware version number. You may need to log in to the Switch again. 15.6 Restore a Configuration File Restore a previously saved configuration from your computer to the Switch using the Restore Configuration screen. ES-315/ES-315-F User's Guide 95
  • ZyXEL ES-315 | User Guide - Page 96
    Command Line This section shows some examples of uploading to or downloading files from the Switch using FTP commands. First, understand the filename conventions. 96 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 97
    Switch, for example, put firmware.bin ras transfers the firmware on your computer (firmware.bin) to the Switch and renames it to "ras". Similarly, put config.cfg config transfers the configuration file on your computer (config.cfg) to the Switch and renames it to ES-315/ES-315-F User's Guide 97
  • ZyXEL ES-315 | User Guide - Page 98
    and firmware files should service is disabled in the Service Access Control screen. • The IP address(es) in the Remote Management screen does not match the client IP address. If it does not match, the Switch will disconnect the Telnet session immediately. 98 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 99
    . 16.2 The Access Control Main Screen Click Management > Access Control in the navigation panel to display the main screen as shown. Figure 51 Access Control ES-315/ES-315-F User's Guide 99
  • ZyXEL ES-315 | User Guide - Page 100
    Allows the manager to set values for object variables within an agent. Trap Used by the agent to inform the manager of some events. 100 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 101
    statistics and monitor status and performance. The Switch supports the following MIBs: • SNMP MIB II (RFC ES-315: 1.3.6.1.4.1.890.1.5.8.41.27.2.2 ES-315-F: 1.3.6.1.4.1.890.1.5.8.42.27.2.2 This trap is sent when the Switch gets the time and date from a time server. ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 102
    fails due to incorrect user name and/or password. AuthenticationFailureEventOn ES-315: 1.3.6.1.4.1.890.1.5.8.41.27.2.1 ES-315-F: 1.3.6.1.4.1.890.1.5.8.42.27.2.1 This trap is sent when a traceroute test fails. This trap is sent when a traceroute test is completed. 102 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 103
    SNMP managers using SNMP version 2c or lower. Trap Destination Enter the IP addresses of up to four managers to send your SNMP traps to. ES-315/ES-315-F User's Guide 103
  • ZyXEL ES-315 | User Guide - Page 104
    who can view but not configure Switch settings. Click Access Control from the navigation panel and then click Logins. Figure 54 Access Control: Logins 104 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 105
    an unsecured network. Figure 55 SSH Communication Example 16.5 How SSH works The following table summarizes how a secure connection is established between two remote hosts. ES-315/ES-315-F User's Guide 105
  • ZyXEL ES-315 | User Guide - Page 106
    to the server to log in to the server. 16.6 SSH Implementation on the Switch Your Switch supports SSH version 2 using RSA authentication and three encryption methods (DES, 3DES and Blowfish). The SSH server system) that is used to connect to the Switch over SSH. 106 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 107
    ) on the Switch's WS (web server). Figure 57 HTTPS Implementation " If you disable HTTP in the Service Access Control screen, then the Switch blocks all HTTP connection attempts. 16.8 HTTPS Example If you haven't or domain name of the Switch you wish to access. ES-315/ES-315-F User's Guide 107
  • ZyXEL ES-315 | User Guide - Page 108
    OK to continue in Netscape. Select Accept this certificate permanently to import the Switch's certificate into the SSL client. Figure 59 Security Certificate 1 (Netscape) 108 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 109
    what services you may use to access the Switch. You may also change the default service port and configure "trusted computer(s)" for each service in the Remote Management screen (discussed later). Click Access Control to go back to the main Access Control screen. ES-315/ES-315-F User's Guide 109
  • ZyXEL ES-315 | User Guide - Page 110
    Control screen, click Remote Management. The following screen displays. You can specify a group of one or more "trusted computers" from which an administrator may use a service to manage the Switch. Click Access Control to return to the Access Control screen. 110 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 111
    can manage this Switch. The Switch checks if the client IP address of a computer requesting a service or protocol matches the range set here. The Switch immediately disconnects the session if it does not Click Cancel to begin configuring this screen afresh. ES-315/ES-315-F User's Guide 111
  • ZyXEL ES-315 | User Guide - Page 112
    Chapter 16 Access Control 112 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 113
    the IP address (in the field to the left). Ethernet Port Test Enter a port number and click Port Test to perform an internal loopback test. ES-315/ES-315-F User's Guide 113
  • ZyXEL ES-315 | User Guide - Page 114
    Chapter 17 Diagnostic 114 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 115
    panel to display this screen. The syslog feature sends logs to an external syslog server. Use this screen to configure the device's system logging settings. ES-315/ES-315-F User's Guide 115
  • ZyXEL ES-315 | User Guide - Page 116
    Syslog Setup screen. Click the Syslog Server Setup link to open the following screen. Use this screen to configure a list of external syslog servers. 116 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 117
    syslog server. Delete Select an entry's Delete check box and click Delete to remove the entry. Cancel Click Cancel to begin configuring this screen afresh. ES-315/ES-315-F User's Guide 117
  • ZyXEL ES-315 | User Guide - Page 118
    Chapter 18 Syslog 118 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 119
    forwarded to which port(s) and whether the MAC address is dynamic (learned by the Switch) or static (manually entered in the Static MAC Forwarding screen). The Switch uses the MAC table to determine how to forward it filters the frame. Figure 67 MAC Table Flowchart ES-315/ES-315-F User's Guide 119
  • ZyXEL ES-315 | User Guide - Page 120
    is the port from which the above MAC address was learned. This shows whether the MAC address is dynamic (learned by the Switch) or static (manually entered in the Static MAC Forwarding screen). 120 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 121
    Table Click Management > ARP Table in the navigation panel to open the following screen. Use the ARP table to view IP-to-MAC address mapping(s). ES-315/ES-315-F User's Guide 121
  • ZyXEL ES-315 | User Guide - Page 122
    address of the device with corresponding IP address above. Type This shows whether the MAC address is dynamic (learned by the Switch) or static. 122 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 123
    Chapter 20 ARP Table ES-315/ES-315-F User's Guide 123
  • ZyXEL ES-315 | User Guide - Page 124
    Chapter 20 ARP Table 124 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 125
    PART VI Troubleshooting and Product Specifications Troubleshooting (127) Product Specifications (131) 125
  • ZyXEL ES-315 | User Guide - Page 126
    126
  • ZyXEL ES-315 | User Guide - Page 127
    connections. See the Quick Start Guide and Section 21.1 on page 127. 3 Inspect your cables for damage. Contact the vendor to replace any damaged cables. 4 Disconnect and re-connect the power cord to the Switch. 5 If the problem continues, contact the vendor. ES-315/ES-315-F User's Guide 127
  • ZyXEL ES-315 | User Guide - Page 128
    it, see the troubleshooting suggestions for I forgot service, such as Telnet. If you can access the Switch, check the remote management settings to find out why the Switch does not respond to HTTP. V I can see the Login screen, but I cannot log in to the Switch. 128 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 129
    Chapter 21 Troubleshooting 1 Make sure you have entered the user name and password correctly. The default user name is admin, and the allow: • Web browser pop-up windows from your device. • JavaScripts (enabled by default). • Java permissions (enabled by default). ES-315/ES-315-F User's Guide 129
  • ZyXEL ES-315 | User Guide - Page 130
    Chapter 21 Troubleshooting 130 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 131
    firmware features. Table 46 Hardware Specifications SPECIFICATION DESCRIPTION Dimensions ES-315: 181.2mm x 126.7mm x 33.2mm ES-315-F: 194.0mm x 129.7mm x 25.9mm Weight ES-315: 277g ES-315-F: 325g Power Specification 12V AC 1A Interfaces ES-315 a router. ES-315/ES-315-F User's Guide 131
  • ZyXEL ES-315 | User Guide - Page 132
    The following scheduling services are supported: Strict Priority configure the TCP/IP parameters manually. Multicast VLAN Registration (MVR) a syslog server. Firmware Upgrade Download new firmware (when available) from the ZyXEL web site and Supports IGMP snooping 132 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 133
    The following list, which is not exhaustive, illustrates the standards supported in the Switch. Table 49 Standards Supported STANDARD DESCRIPTION RFC 826 Address Resolution Protocol (ARP) RFC 867 VLAN IEEE 802.3 Packet Format IEEE 802.3x Flow Control ES-315/ES-315-F User's Guide 133
  • ZyXEL ES-315 | User Guide - Page 134
    49 Standards Supported (continued) STANDARD DESCRIPTION Safety UL 60950-1 CSA 60950-1 EN 60950-1 IEC 60950-1 EMC FCC Part 15 (Class B) CE EMC (Class B) 22.2 Wall-mounting Instructions Complete Switch on the screws. Figure 70 Wall-mounting Example: ES-315 134 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 135
    Figure 71 Wall-mounting Example: ES-315-F Chapter 22 Product Specifications The following are dimensions of an M4 tap screw and masonry plug used for wall mounting. All measurements are in millimeters (mm). Masonry Plug ES-315/ES-315-F User's Guide 135
  • ZyXEL ES-315 | User Guide - Page 136
    Chapter 22 Product Specifications 136 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 137
    PART VII Appendices and Index IP Addresses and Subnetting (139) Common Services (149) Legal Information (153) Customer Support (157) Index (163) 137
  • ZyXEL ES-315 | User Guide - Page 138
    138
  • ZyXEL ES-315 | User Guide - Page 139
    an example IP address in which the first three octets (192.168.1) are the network number, and the fourth octet (16) is the host ID. ES-315/ES-315-F User's Guide 139
  • ZyXEL ES-315 | User Guide - Page 140
    with a "1" value). For example, an "8-bit mask" means that the first 8 bits of the mask are ones and the remaining 24 bits are zeroes. 140 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 141
    Notation SUBNET MASK ALTERNATIVE NOTATION LAST OCTET (BINARY) LAST OCTET (DECIMAL) 255.255.255.0 /24 0000 0000 0 255.255.255.128 /25 1000 0000 128 ES-315/ES-315-F User's Guide 141
  • ZyXEL ES-315 | User Guide - Page 142
    subnets; 192.168.1.0 /25 and 192.168.1.128 /25. The following figure shows the company network after subnetting. There are now two subnetworks, A and B. 142 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 143
    (Binary) 11111111.11111111.11111111. 11000000 Subnet Address: 192.168.1.0 Lowest Host ID: 192.168.1.1 Broadcast Address: 192.168.1.63 Highest Host ID: 192.168.1.62 ES-315/ES-315-F User's Guide 143
  • ZyXEL ES-315 | User Guide - Page 144
    Subnets SUBNET SUBNET ADDRESS FIRST ADDRESS LAST ADDRESS BROADCAST ADDRESS 1 0 1 30 31 2 32 33 62 63 3 64 65 94 95 4 96 97 126 127 144 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 145
    ) 1024 62 11 255.255.255.224 (/27) 2048 30 12 255.255.255.240 (/28) 4096 14 13 255.255.255.248 (/29) 8192 6 ES-315/ES-315-F User's Guide 145
  • ZyXEL ES-315 | User Guide - Page 146
    to change the subnet mask computed by the Switch unless you are instructed to do otherwise. Private IP Addresses Every machine on the Internet must you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 147
    DHCP server assigns to computer B which is a DHCP client. Neither can access the Internet. This problem can be solved by assigning a different static IP address to computer A or setting computer A to networks. Figure 76 Conflicting Computer IP Addresses Example ES-315/ES-315-F User's Guide 147
  • ZyXEL ES-315 | User Guide - Page 148
    's LAN port both use 192.168.1.1 as the IP address. The computer cannot access the Internet. This problem can be solved by assigning a different IP address to the computer or the router's LAN port. Figure 77 Conflicting Computer and Router IP Addresses Example 148 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 149
    , a service that matches web names (for example www.zyxel.com) to IP numbers. The IPSEC ESP (Encapsulation Security Protocol) tunneling protocol uses this service. Finger is a UNIX or Internet related command that can be used to find out if a user is logged on. ES-315/ES-315-F User's Guide 149
  • ZyXEL ES-315 | User Guide - Page 150
    channel. PPTP (Point-to-Point Tunneling Protocol) enables secure transfer of data over public networks. This is the data channel. Remote Command Service. A streaming audio service that enables real time sound over the web. Remote Execution Daemon. Remote Login. 150 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 151
    Appendix B Common Services Table 61 Commonly Used Services (continued) NAME RTELNET RTSP SFTP SMTP PROTOCOL TCP TCP/UDP TCP TCP SNMP SNMP- uses the UDP (User Datagram Protocol) rather than TCP (Transmission Control Protocol). Another videoconferencing solution. ES-315/ES-315-F User's Guide 151
  • ZyXEL ES-315 | User Guide - Page 152
    Appendix B Common Services 152 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 153
    , uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. ES-315/ES-315-F User's Guide 153
  • ZyXEL ES-315 | User Guide - Page 154
    warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser. 154 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 155
    C Legal Information To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. ES-315/ES-315-F User's Guide 155
  • ZyXEL ES-315 | User Guide - Page 156
    Appendix C Legal Information 156 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 157
    Web: www.zyxel.co.cr • FTP: ftp.zyxel.co.cr • Regular Mail: ZyXEL Costa Rica, Plaza Roble Escazú, Etapa El Patio, Tercer Piso, San José, Costa Rica Czech Republic • E-mail: [email protected] • Telephone: +420-241-091-350 • Fax: +420-241-091-359 • Web: www.zyxel.cz ES-315/ES-315-F User's Guide 157
  • ZyXEL ES-315 | User Guide - Page 158
    Adenauerstr. 20/A2 D-52146, Wuerselen, Germany Hungary • Support E-mail: [email protected] • Sales E-mail: [email protected] • Telephone: +36-1-3361649 • Fax: +36-1-3259100 • Web: www.zyxel.hu • Regular Mail: ZyXEL Hungary, 48, Zoldlomb Str., H-1025, Budapest, Hungary 158 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 159
    Bandar Puchong Jaya, 47100 Puchong, Selangor Darul Ehsan, Malaysia North America • Support E-mail: [email protected] • Sales E-mail: [email protected] • Telephone: +1-800-255-4101, +1-714-632-0882 • Fax: +1-714-632-0858 • Web: www.us.zyxel.com • FTP: ftp.us.zyxel.com ES-315/ES-315-F User's Guide 159
  • ZyXEL ES-315 | User Guide - Page 160
    Park, The Strategy #03-28, Singapore 609930 Spain • Support E-mail: [email protected] • Sales E-mail: [email protected] • Telephone: +34-902-195-420 • Fax: +34-913-005-345 • Web: www.zyxel.es • Regular Mail: ZyXEL Communications, Arte, 21 5ª planta, 28033 Madrid, Spain 160 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 161
    @zyxel.co.uk • Telephone: +44-1344-303044, 08707-555779 (UK only) • Fax: +44-1344-303034 • Web: www.zyxel.co.uk • FTP: ftp.zyxel.co.uk • Regular Mail: ZyXEL Communications UK Ltd., 11 The Courtyard, Eastern Road, Bracknell, Berkshire RG12 2XB, United Kingdom (UK) ES-315/ES-315-F User's Guide 161
  • ZyXEL ES-315 | User Guide - Page 162
    Appendix D Customer Support 162 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 163
    account 104 remote management 110 service port 109 SNMP 100 Address ES-315/ES-315-F User's Guide Index Index change running config 94 configuration file backup 96 restore 95 saving 94 configuration, saving 37 contact information 157 copyright 153 current date 48 current time 48 customer support
  • ZyXEL ES-315 | User Guide - Page 164
    IANA 146 introduction 23 IP capability 133 services 133 164 IP address 52 IP interface configuration backup 96 current configuration 93 firmware 95 main screen 93 restoring supported MIBs 101 MIB (Management Information Base) 100 MTU (Multi-Tenant Unit) 49 multicast 73 ES-315/ES-315-F User's Guide
  • ZyXEL ES-315 | User Guide - Page 165
    queue weight 72 queuing 71 queuing algorithm 72 queuing method 71, 72 ES-315/ES-315-F User's Guide R reboot load configuration 94 reboot system 94 registration product 155 related documentation 3 remote management 110 service 111 trusted computers 111 resetting 38, 94 to factory default settings 94
  • ZyXEL ES-315 | User Guide - Page 166
    57 temperature 131 time current 48 time zone 49 Time (RFC-868) 48 time server 48 time service protocol 48 format 48 trademarks 153 traps destination 103 trunking 132 V VID 57, 58, 59 38 navigation panel 35 screen summary 35 Z ZyNOS (ZyXEL Network Operating System) 97 ES-315/ES-315-F User's Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166

www.zyxel.com
ES-315
ES-315-F
Intelligent Layer 2 Managed Switch
User’s Guide
Version 3.70
8
/2007
Edition 1
DEFAULT LOGIN
IP Address
User Name
admin
Password
1234