2008 BMW X3 Owner's Manual - Page 111

2008 BMW X3 Manual

Get 2008 BMW X3 PDF manuals and user guides View all 2008 BMW X3 manuals

Page 111 highlights

bracket. To do so, loosen the bolt, refer to arrow, and place the reservoir to one side. Bear in mind that the windshield washing system reservoir is heavy. Failure to take this into account can lead to personal injury or damage to the vehicle.< For bulb replacement procedure, refer to Driver's side. Front passenger side Before replacing the bulb, remove the reservoir of the windshield washer system from the bracket, refer to Halogen low beams on page 108. For bulb replacement procedure, refer to Driver's side. Parking and roadside parking lamps Halogen high beams H7 bulb, 55 watts Always wear gloves and eye protection - the atmosphere inside the H7 bulb is pressurized. Failure to observe this precaution can lead to injuries should the bulb be damaged.< For checking and adjusting headlamp aim, please contact your BMW Sports Activity Vehicle Center.< W5W bulb, 5 watts A bulb is located over each high beam. 1. Remove bulb cover for high beams, refer to Halogen high beams. 2. Remove bulb holder. 3. Remove and replace the bulb. Controls Reference Mobility Driving tips Turn signal, front Driver's side 1. Open the clip and remove the lamp cover. PSY24WSV bulb, 24 watts Access to the turn signal is at the edge of the lamp unit, refer to arrow. 2. Press the bulb holder downward and remove, refer to Low beams. 3. Pull off the lamp base; plug in a new lamp base. 4. Place the lamp base with the lower edge against the bracket and press it in until the lamp base locks into place. Make sure that the cover does not fall into the engine compartment; otherwise, the vehicle can be damaged or other road users can be endangered.< Make sure that the lamp base does not fall into the engine compartment; otherwise, the vehicle can be damaged or other road users can be endangered.< 1. Turn the lamp base and remove it. 2. Replace the bulb. 3. Insert the lamp base. If it does not snap into place immediately, turn the lamp base until it does. 109 Online Edition for Part no. 01 41 0 014 250 - © 08/07 BMW AG At a glance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Reference
At a glance
Controls
Driving tips
Mobility
109
bracket. To do so, loosen the bolt, refer to
arrow, and place the reservoir to one side.
Bear in mind that the windshield washing
system reservoir is heavy. Failure to take
this into account can lead to personal injury or
damage to the vehicle.
<
For bulb replacement procedure, refer to
Driver's side.
Halogen high beams
H7 bulb, 55 watts
Always wear gloves and eye protection –
the atmosphere inside the H7 bulb is
pressurized. Failure to observe this precaution
can lead to injuries should the bulb be dam-
aged.
<
For checking and adjusting headlamp
aim, please contact your BMW Sports
Activity Vehicle Center.
<
Driver's side
1.
Open the clip and remove the lamp cover.
2.
Press the bulb holder downward and
remove, refer to Low beams.
3.
Pull off the lamp base; plug in a new lamp
base.
4.
Place the lamp base with the lower edge
against the bracket and press it in until the
lamp base locks into place.
Make sure that the cover does not fall into
the engine compartment; otherwise, the
vehicle can be damaged or other road users can
be endangered.
<
Front passenger side
Before replacing the bulb, remove the reservoir
of the windshield washer system from the
bracket, refer to Halogen low beams on
page
108
.
For bulb replacement procedure, refer to
Driver's side.
Parking and roadside parking lamps
W5W bulb, 5 watts
A bulb is located over each high beam.
1.
Remove bulb cover for high beams, refer to
Halogen high beams.
2.
Remove bulb holder.
3.
Remove and replace the bulb.
Turn signal, front
PSY24WSV bulb, 24 watts
Access to the turn signal is at the edge of the
lamp unit, refer to arrow.
Make sure that the lamp base does not fall
into the engine compartment; otherwise,
the vehicle can be damaged or other road users
can be endangered.
<
1.
Turn the lamp base and remove it.
2.
Replace the bulb.
3.
Insert the lamp base. If it does not snap into
place immediately, turn the lamp base until
it does.