2006 Ford Crown Victoria Severe Duty Police/Fleet Supplement 2nd Printing - Page 13

2006 Ford Crown Victoria Manual

Page 13 highlights

Severe duty equipment The Fire Suppression System is mounted beneath the vehicle and attached to the frame above and forward of the fuel tank and rear axle. The Fire System Control Module is mounted inside the passenger compartment centered underneath the rear seat cushion. The system is designed to deploy automatically after sensing a high-speed/high-energy rear end impact. There is a covered manual activation switch mounted in a console on the headliner between the visors that can be used by vehicle occupants to manually deploy the system. The fire suppression system can be manually deployed anytime the vehicle is in a Key ON or Engine ON mode by pushing the button underneath the cover. The button can be accessed three ways: 1. Pushing on the cover will release the cover latch, allowing the door to swing open and expose the button; 2. The cover can be pulled open; 3. A firm strike on the cover (about 20 lbs of force) will deploy the system anytime the vehicle is in a Key ON or Engine ON mode. In the event of a manual deployment, nozzles will deploy to near ground level and the underbody of the vehicle will be covered with suppressant fluid. The suppressant contains no hazardous materials (but may cause minor skin or eye irritation) and can be readily cleaned up by flushing the underbody with water (or soap and water). Manual deployment should have no adverse affect on vehicle handling; however, caution should be exercised in moving the vehicle as ground clearance will be compromised by the deployed nozzles. Because of reduced ground clearance, the vehicle should not be driven through an automatic car wash with nozzles in the deployed condition. The fire suppression system is a single use system-all major components will have to be replaced in the event of a manual deployment. Figure A The approved ISO symbol for Fire Suppression is shown in Figure A. This symbol is printed on the manual activation switch and on the diagnostic telltale on the instrument cluster. 13 2006 Crown Victoria (cro) Supplement USA (fus)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

The Fire Suppression System is mounted beneath the vehicle and attached
to the frame above and forward of the fuel tank and rear axle. The Fire
System Control Module is mounted inside the passenger compartment
centered underneath the rear seat cushion. The system is designed to deploy
automatically after sensing a high-speed/high-energy rear end impact.
There is a covered manual activation switch mounted in a console on the
headliner between the visors that can be used by vehicle occupants to
manually deploy the system. The fire suppression system can be
manually deployed anytime the vehicle is in a Key ON or Engine ON
mode by pushing the button underneath the cover. The button can be
accessed three ways:
1. Pushing on the cover will release the cover latch, allowing the door to
swing open and expose the button;
2. The cover can be pulled open;
3. A firm strike on the cover (about 20 lbs of force) will deploy the
system anytime the vehicle is in a Key ON or Engine ON mode.
In the event of a manual deployment, nozzles will deploy to near ground
level and the underbody of the vehicle will be covered with suppressant
fluid. The suppressant contains no hazardous materials (but may cause
minor skin or eye irritation) and can be readily cleaned up by flushing
the underbody with water (or soap and water). Manual deployment
should have no adverse affect on vehicle handling; however, caution
should be exercised in moving the vehicle as ground clearance will be
compromised by the deployed nozzles. Because of reduced ground
clearance, the vehicle should not be driven through an automatic car
wash with nozzles in the deployed condition.
The fire suppression system is a single use system—all major components
will have to be replaced in the event of a manual deployment.
Figure A
The approved ISO symbol for Fire Suppression is shown in Figure A.
This symbol is printed on the manual activation switch and on the
diagnostic telltale on the instrument cluster.
2006 Crown Victoria
(cro)
Supplement
USA
(fus)
Severe duty equipment
13