2013 Ford F350 Super Duty Super Cab Diesel Supplement Printing 1 - Page 39

2013 Ford F350 Super Duty Super Cab Manual

Get 2013 Ford F350 Super Duty Super Cab PDF manuals and user guides View all 2013 Ford F350 Super Duty Super Cab manuals

Page 39 highlights

Fuel and Refueling Base information display procedure 1. Start with the vehicle engine fully warmed. 2. Press the Info button on the steering wheel until the information display reads one of the following choices: • If the DPF needs cleaning and the vehicle is warmed up, a message requesting permission to initiate filter cleaning will be displayed EXHST XX% FULL CLEAN Y/N or EXHAUST FILTER FULL. Answer yes to this prompt and then follow the prompts regarding exhaust position as needed to initiate OCR. Be sure to understand each prompt. If you are not sure what is being asked by each prompt, contact your authorized dealer. The display will confirm the operation has started and when it has finished. • If the vehicle is warmed up, the powertrain fault indicator will illuminate and messages requesting permission to initiate filter cleaning will be displayed DRIVE TO CLEAN EXHAUST FILTER + EXH OVERLOADED CLEAN? Y/N . Answer yes to this prompt and then follow the prompts regarding exhaust position as needed to initiate OCR. Be sure to understand each prompt. If you are not sure what is being asked by each prompt, contact your authorized dealer. The display will confirm the operation has started and when it has finished. You can also drive to clean the filter. See Active regeneration earlier in this chapter. • The service engine soon light will illuminate and the following messages EXH OVERLOADED CLEAN? Y/N + REDUCED ENGINE POWER will appear when the system is at the point of oversaturation you will not be able to allow cleaning . The vehicle must be serviced by an authorized dealer. 3. Once OCR starts, the engine's rpm will rise to approximately 2,000 2,400 rpm and the cooling fan will increase speed; you will hear a change in audible sound due to the fan and engine speed increase. It is not necessary to open the hood on the engine compartment. Once OCR is complete, the engine rpm and fan will return to normal idling. The exhaust system will remain very hot for several minutes even after regeneration is complete. Do not reposition the vehicle over materials that could burn until the exhaust system has had sufficient time to cool. Depending on the amount of soot collected by the DPF, ambient temperature, and altitude, OCR may last from 10 to 25 minutes. 38 2013 Diesel (67l) Supplement, 1st Printing USA (fus)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Base information display procedure
1. Start with the vehicle engine fully warmed.
2. Press the Info button on the steering wheel until the information
display reads one of the following choices:
•
If the DPF needs cleaning and the vehicle is warmed up, a message
requesting permission to initiate filter cleaning will be displayed
EXHST XX% FULL CLEAN Y/N
or
EXHAUST FILTER FULL
.
Answer yes to this prompt and then follow the prompts regarding
exhaust position as needed to initiate OCR. Be sure to understand
each prompt. If you are not sure what is being asked by each prompt,
contact your authorized dealer. The display will confirm the operation
has started and when it has finished.
•
If the vehicle is warmed up, the
powertrain fault indicator will
illuminate and messages
requesting permission to initiate filter cleaning will be displayed
DRIVE TO CLEAN EXHAUST FILTER
+
EXH OVERLOADED
CLEAN? Y/N
. Answer yes to this prompt and then follow the
prompts regarding exhaust position as needed to initiate OCR. Be sure
to understand each prompt. If you are not sure what is being asked by
each prompt, contact your authorized dealer. The display will confirm
the operation has started and when it has finished. You can also drive
to clean the filter. See
Active regeneration
earlier in this chapter.
•
The service engine soon light will
illuminate and the following
messages
EXH OVERLOADED
CLEAN? Y/N
+
REDUCED ENGINE POWER
will appear when the
system is at the point of oversaturation you will not be able to allow
cleaning . The vehicle must be serviced by an authorized dealer.
3. Once OCR starts, the engine’s rpm will rise to approximately 2,000 -
2,400 rpm and the cooling fan will increase speed; you will hear a change
in audible sound due to the fan and engine speed increase.
It is not necessary to open the hood on the engine compartment. Once
OCR is complete, the engine rpm and fan will return to normal idling.
The exhaust system will remain very hot for several minutes even after
regeneration is complete. Do not reposition the vehicle over materials
that could burn until the exhaust system has had sufficient time to
cool. Depending on the amount of soot collected by the DPF, ambient
temperature, and altitude, OCR may last from 10 to 25 minutes.
Fuel and Refueling
38
2013 Diesel
(67l)
Supplement, 1st Printing
USA
(fus)