1998 Lincoln Mark VIII Owner Guide 1st Printing - Page 49

1998 Lincoln Mark VIII Manual

Page 49 highlights

Controls and features Training a rolling code system Rolling code systems (garage door openers which are "code protected") may be determined by the following: • The hand-held transmitter appears to program the HomeLink௡ Universal Transmitter but does not activate the garage door. • The garage door opener was manufactured after 1995. Follow these steps to train a garage door with the rolling code feature: 1. Locate the training control on the garage door opener receiver. Refer to the garage door opener manual or call 1-800-355-3515 if there is difficulty locating the training control. 2. Press the training control on the garage door opener receiver until the training light (next to the control) begins to flash (1-2 seconds). 3. Press the programmed HomeLink௡ control in the vehicle until the training light on the garage door receiver turns solid (1-2 seconds). Release the HomeLink௡ control and repress to turn off the training light. 4. Press the HomeLink௡ control again. If the garage door activates, the HomeLink௡ Universal Transmitter has been trained to the receiver. Erasing channels To erase all three programmed channels: 1. Hold down the two outside controls until the red light begins to flash. 2. Release both controls. Channels cannot be erased individually, but can be reprogrammed. Refer to Programming for instructions. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170

Training a rolling code system
Rolling code systems (garage door openers which are “code protected”)
may be determined by the following:
The hand-held transmitter appears to program the HomeLink
t
Universal Transmitter but does not activate the garage door.
The garage door opener was manufactured after 1995.
Follow these steps to train a garage door with the rolling code feature:
1. Locate the training control on the garage door opener receiver. Refer
to the garage door opener manual or call 1–800–355–3515 if there is
difficulty locating the training control.
2. Press the training control on the garage door opener receiver until the
training light (next to the control) begins to flash (1-2 seconds).
3. Press the programmed
HomeLink
t
control in the vehicle
until the training light on the garage
door receiver turns solid (1-2
seconds). Release the HomeLink
t
control and repress to turn off the
training light.
4. Press the HomeLink
t
control
again. If the garage door activates,
the HomeLink
t
Universal
Transmitter has been trained to the
receiver.
Erasing channels
To erase all three programmed
channels:
1. Hold down the two outside
controls until the red light begins to
flash.
2. Release both controls.
Channels cannot be erased
individually, but can be
reprogrammed. Refer to
Programming
for instructions.
Controls and features
50