2012 Toyota Sienna Navigation Manual
2012 Toyota Sienna Manual
2012 Toyota Sienna manual content summary:
- 2012 Toyota Sienna | Navigation Manual - Page 1
SIENNA 2 0 1 2 CUSTOMER EXPERIENCE CENTER 1-800-331-4331 NAVIGATION SYSTEM QUICK REFERENCE GUIDE Printed in U.S.A. 8/11 11-TCS-05013 00505-NAV12-SIE - 2012 Toyota Sienna | Navigation Manual - Page 2
to provide information on the basic operation and key features of the navigation system. The Quick Reference Guide is not intended as a substitute for the Navigation Owner's Manual. We strongly encourage you to review the Navigation Owner's Manual so you will have a better understanding of the - 2012 Toyota Sienna | Navigation Manual - Page 3
balance and tone controls. SETUP Button Adjust Preferences for: INFO/PHONE Button Access Phone, Map Data feature, or display the current position. CURRENT VEHICLE POSITION Mark Indicates the current position of the vehicle and its directional heading. NORTH-UP OR COMPASS MODE Icon Touch to change - 2012 Toyota Sienna | Navigation Manual - Page 4
Press by DEST on the faceplate followed step . 2 Touch and move to step 4. To change Search Area, touch and move to step 3. step 3 Select the desired Search Area and such as North or the letter N. The system will display the base street name without prefixes or suffixes on the next screen. 3 - 2012 Toyota Sienna | Navigation Manual - Page 5
DESTINATION INPUT BY ADDRESS step 7 Touch the desired street name. step 8 Input the house number and touch . step 9 Touch . step 10 Select the desired Route Preferences by touching followed by . Touch to confirm selection. step 11 Touch guidance. to start route 4 - 2012 Toyota Sienna | Navigation Manual - Page 6
recognition feature will compare your spoken words with computer-generated word patterns preprogrammed in the database. If the system does not provide your intended match, please try a different pronunciation. Voice-activation names are not available for every street and city. TIPS FOR USING VOICE - 2012 Toyota Sienna | Navigation Manual - Page 7
DESTINATION INPUT BY ADDRESS-VOICE RECOGNITION step 3 After the beep say the city name or, "Change state" to search in another state. step 4 After the beep say the street name. step 5 After the beep say the house number. step 6 After the - 2012 Toyota Sienna | Navigation Manual - Page 8
(POI) POINT OF INTEREST BY NAME step 1 Press DEST on the faceplate followed by . step 2 Touch . step 3 Input the POI name and touch . step 4 Use or to scroll up or down. Touch the desired destination. Quick Tip - If the POI isn't listed in the database verify the spelling and Search - 2012 Toyota Sienna | Navigation Manual - Page 9
by . step 2 Touch . step 3 Touch the desired category location. step 4 Touch the desired category icon followed by the desired sub-category. step 5 Use or to scroll up or down. Touch the desired point of interest. step 6 . See page 15 to select Touch desired Route Preference. Touch - 2012 Toyota Sienna | Navigation Manual - Page 10
DESTINATION INPUT - POINT OF INTEREST (POI) POINT OF INTEREST BY CATEGORY - VOICE RECOGNITION step 1 Press on the steering wheel. After the beep say, "Destination." step 2 After the beep say, "Point of Interest." Quick Tip - If you know your next command, you can press at any time to - 2012 Toyota Sienna | Navigation Manual - Page 11
SET HOME step 1 Press by SETUP on the faceplate followed . step 2 Touch . step 3 Touch . step 4 Touch . Tip - For security reasons, use a point close to your home instead of your actual home address. step 5 Make sure you are in the desired Search Area. Touch . step 6 Input - 2012 Toyota Sienna | Navigation Manual - Page 12
such as North or the letter N. The system will display the base street name without prefixes or suffixes on the next screen. step 9 Touch the desired street name. step 10 Input the house number and touch . step 11 Touch icon. followed by to change - 2012 Toyota Sienna | Navigation Manual - Page 13
on the phone is ON and is in discoverable mode. step 3 Input the passkey listed on the screen into the approved Bluetooth cell phone. Please refer to the cell phone manufacturer's user guide for pairing procedures. step 4 Upon connection, the system will indicate that the pairing process was - 2012 Toyota Sienna | Navigation Manual - Page 14
say "Dial" or press on the steering wheel. Some Bluetooth® equipped cell phones may or may not show battery or system from understanding your commands. It is recommended that you reduce background noise (including passenger conversation and wind noise) prior to using the Voice Recognition system - 2012 Toyota Sienna | Navigation Manual - Page 15
, or are unable to transfer your cell phone book, please refer to the cell phone manufacturer's user guide. If you are able to successfully transfer your phone book, you can dial by name using voice recognition. Please say the name exactly as it is entered in your phone when in the telephone - 2012 Toyota Sienna | Navigation Manual - Page 16
- is the second fastest route Short- is the most direct based upon driven mileage Single Sing gle Map * Turn List Dual Map * Arrow available when the map is visible and three additional are available during route guidance only. Freeway Information * Selections available when in guidance mode - 2012 Toyota Sienna | Navigation Manual - Page 17
Time option. AUTO SCREEN CHANGE VOICE RECOGNITION GUIDANCE PRESS SETUP > PRESS SETUP > Once the screen transition is switched off, the audio screen will remain without reverting to the map display. Disables system guidance for voice commands. Only on-screen guidance will be available when - 2012 Toyota Sienna | Navigation Manual - Page 18
ADDITIONAL NAVIGATION FEATURES ESTIMATED DISTANCE AND TIME - 2012 Toyota Sienna | Navigation Manual - Page 19
.com. If you decide to continue your SiriusXM service at the end of your complimentary trial, the plan you choose will automatically renew and bill at then-current rates until you call 1-866-635-2349 to cancel. Fees and programming subject to change. Available only to those at least 18 years of age - 2012 Toyota Sienna | Navigation Manual - Page 20
bar appears, the preference has been selected. Touch , traffic flow is displayed by colored lines alongside freeway or highways: Free flow traffic Moderate traffic Heavy congestion AUTO AVOID TRAFFIC step 1 Press by SETUP on the faceplate followed . step 2 Touch . step 3 19 Select from the - 2012 Toyota Sienna | Navigation Manual - Page 21
voice notification of traffic events within 20 miles along the current route. Touch followed by . SHOW FREE FLOWING TRAFFIC step 1 Press by SETUP on the faceplate followed . step 2 Touch . step 3 Select from the Show Free Flowing Traffic option. Touch followed by . Free flowing traffic is - 2012 Toyota Sienna | Navigation Manual - Page 22
feature. After the beep, say one of the voice commands shown on the screen or listed below. Please refer to the Navigation Owner's Manual for additional information. AUDIO MODE MODE Radio AM FM FM1 FM2 Satellite Radio* Satellite Radio 1* Satellite Radio 2* Satellite Radio 3* CD CD Changer Bluetooth - 2012 Toyota Sienna | Navigation Manual - Page 23
Bowling Centers Entertainment Golf Courses Health & Fitness Clubs Horse Racing Parks & Beaches Marinas Motor Sports Nightlife Performing Arts Ski Resorts Sports Complexes Sports & Fitness Automotive Automobile Clubs Auto Service & Maint. Car Rental Agencies Car Washes Dealerships Gas Lexus Parking - 2012 Toyota Sienna | Navigation Manual - Page 24
BASIC FUNCTIONS SECTION BASIC FUNCTIONS Basic information before operation 1 D Display operation ...22 D Initial screen ...23 D Touch screen operation ...25 D Inputting letters and numbers/List screen operation ...25 D Function help ...29 D Map screen operation ...Current position display ... - 2012 Toyota Sienna | Navigation Manual - Page 25
positions 1 , 2 , 3 and then back to 0 in the reverse order. If the engine switch is set at OFF, the display will automatically move back to position 0 . The it is moving. It could damage your navigation system. INFORMATION Under extremely cold conditions, the display may react slowly or operation - 2012 Toyota Sienna | Navigation Manual - Page 26
" screen are touched, the screen will change back to "CAUTION" screen and then change to the map screen in about 5 seconds later or if the "MAP/VOICE" button is pushed. CAUTION When the vehicle is stopped with the engine running, always apply the parking brake for safety. After a few seconds - 2012 Toyota Sienna | Navigation Manual - Page 27
parts or components and shows dealer information (if registered) on the screen. When the vehicle reaches a previously set driving distance or date specified for a scheduled maintenance check, the "Information" screen will be displayed when the navigation system is in operation. D Memo information - 2012 Toyota Sienna | Navigation Manual - Page 28
system is operated mainly by the touch screen buttons on the screen. To prevent damage to the screen, lightly touch buttons on the screen with the finger. When a button on the screen is touched, a beep sounds. Do not use be dark and hard to see. If so, change the angle of the screen, look at the - 2012 Toyota Sienna | Navigation Manual - Page 29
BASIC FUNCTIONS D To input letters To display the alphabet keys, touch "A−Z" or " ". D To input numbers and symbols To display the number keys and symbol keys, touch "0−9". 1U5005F Enter letters by touching the alphabet keys directly. Touching this button erases one letter. By holding this button - 2012 Toyota Sienna | Navigation Manual - Page 30
the list D List screen operation When a list is displayed, use the appropriate button to scroll through the list. 1U5007F 1U5009F To side of the screen. If the number of matching items is more than 9999, the system displays on the screen. If appears to the right of the item name, the complete - 2012 Toyota Sienna | Navigation Manual - Page 31
2. Select the desired sorting criteria. Sorting criteria are as follows: "Distance": To sort in the order of distance from your current location. "Date": To sort in the order of the date. "Category": To sort in the order of the category. "Icon": To sort in the order of the icons. "Name": To sort - 2012 Toyota Sienna | Navigation Manual - Page 32
display When starting the navigation system, the current position is displayed first. This screen displays the current vehicle position and a map of the surrounding local area. 1U5056F 1U5015F Touch . The current vehicle position mark ( 1 ) appears in the center or bottom center of the map screen - 2012 Toyota Sienna | Navigation Manual - Page 33
be set as a destination using the one−touch scroll function. 1U5016F 1U5017F Use the scroll feature to move the desired point to the center of the screen for to the center of the screen and the map moves as the vehicle proceeds along the designated route. Touch "Enter ". The screen changes and - 2012 Toyota Sienna | Navigation Manual - Page 34
BASIC FUNCTIONS D To register the cursor position as a memory point Memory point registration enables easy access to a specific point. To change the icon or name, etc., see " - Editing memory points" on page 96. Up to 106 memory points can be registered. If there is an attempt - 2012 Toyota Sienna | Navigation Manual - Page 35
BASIC FUNCTIONS D To see information about the icon where the cursor is set POI INFORMATION When the cursor is set on a POI icon, the name and "Info." are displayed on the top of the screen. 1U5021F 1U5022F To display information about an icon, set the cursor on it. Touch "Info.". 1U5060F - 2012 Toyota Sienna | Navigation Manual - Page 36
BASIC FUNCTIONS MEMORY POINT INFORMATION When the cursor is set on a memory point icon, the name and "Info." are displayed on the top of the screen. DESTINATION INFORMATION When the cursor is set on a destination icon, the name and "Info." are displayed on the top of the screen. 1U5024F Touch " - 2012 Toyota Sienna | Navigation Manual - Page 37
See page 35.) 1U5028F 1. Touch this button to display the following screen. : To display the dual map screen. (See page 35.) : To display the compass mode screen. (See page 36.) : To display the turn list screen. (See page 70.) : To display the arrow screen. (See page 70.) : To display the freeway - 2012 Toyota Sienna | Navigation Manual - Page 38
specific point on the right side map. 1U5059F This screen can perform the following procedures: 1. Changing the map scale 2. Displaying the POI icon 3. Show XMr NavTraffic Info. (See page 118.) 4. Changing the orientation of the map Touch "OK" when you complete editing. The screen returns to the - 2012 Toyota Sienna | Navigation Manual - Page 39
bar directly. It is not available while driving. The map scale is displayed under the north−up symbol or heading−up symbol at the top left of the screen. INFORMATION When the vehicle travels out of the coverage area, the guidance screen changes to the compass mode screen. INFORMATION When the map - 2012 Toyota Sienna | Navigation Manual - Page 40
to the foot print map changes into when the map is scaled down to 150 feet (50 m). D To display building information Information is available only for buildings for the database were created and provided by MAPMASTER. 1U5037F 2. Using the eight−direction arrow, move the cursor to the position of - 2012 Toyota Sienna | Navigation Manual - Page 41
BASIC FUNCTIONS - Orientation of the map The orientation of the map can be changed from North−up to Heading−up by touching the orientation symbol at the top left of the screen. Touch or . 1U5038F Details of POIs in - 2012 Toyota Sienna | Navigation Manual - Page 42
screen) ...40 D Destination search ...41 Selecting the region to search ...Destination search by Home ...Destination search by Quick access ...Destination search by "Address" ...Destination search by "POI" ...Destination search by "Phone #" ...Destination search by "Emergency" ...Destination search - 2012 Toyota Sienna | Navigation Manual - Page 43
1 "Address" A house number and the street address can be input by using the input keys...45 2 "POI" Select one of the many POIs (Points of 6 "Emergency" One of the four categories of emergency service points that are already stored in the system's database can be selected...57 7 "Map" A destination - 2012 Toyota Sienna | Navigation Manual - Page 44
destinations can be deleted...62 12 "Change" To change the selected region to search, touch this button...42 13 Quick access touch screen buttons One of 5 setting screen. To use this function, it is necessary to set the "Quick Access" for each memory point. (To register a "Quick Access", see " - - 2012 Toyota Sienna | Navigation Manual - Page 45
button. SELECTING THE REGION TO SEARCH ON THE INPUT SCREEN Change the selected region in order to set a destination from a different region by using "Address", "POI", "Freeway Ent./Exit" or "Intersection". 2U5069F 2U5004aF 2. Touch "Change" on the "Destination" screen to display a map of the United - 2012 Toyota Sienna | Navigation Manual - Page 46
DESTINATION SEARCH U.S.A. Button "US1" "US2" States included in the search region Idaho Oregon Washington California Nevada Arizona Colorado Montana New Mexico Utah Wyoming Iowa Kansas Minnesota Missouri North Dakota Nebraska South Dakota Oklahoma Texas Illinois Indiana Kentucky Michigan Ohio - 2012 Toyota Sienna | Navigation Manual - Page 47
switch to the setting screen. To use this function, it is necessary to set "Home" for the memory point. (To register "Home", see page 102.) 2U5072F 2. Touch any of the quick access touch screen buttons on the "Destination" screen. The screen changes and displays the map location of the - 2012 Toyota Sienna | Navigation Manual - Page 48
DESTINATION SEARCH - Destination search by "Address" There are 2 ways to input a destination by address. 1. Push the "DEST" button. 2. Touch "Address" on the "Destination" screen. (a) Inputting a house number and a street name 2U5009F 2U5008F 1. Touch numbers directly on the screen to input a - 2012 Toyota Sienna | Navigation Manual - Page 49
Starting route guidance" on page 63.) If the same address exists in more than one city, the current screen changes to the city list screen. 2U5013F If inputting a street name first, the screen changes. The house number can then be input. 2U5014F If the above screen appears, an address range on the - 2012 Toyota Sienna | Navigation Manual - Page 50
the displayed list. "Map": To display the selected destination and the route preference. (See "Starting route guidance" on page 63.) The current screen changes to the screen for inputting a house number or a street name. (See "(a) Inputting a house number and a street name" on page 45.) INFORMATION - 2012 Toyota Sienna | Navigation Manual - Page 51
street name" on page 45.) Touch the button of the desired city name. If the navigation has never been used, no cities will be displayed on the screen. The current screen changes to the screen for inputting a house number or a street name. (See "(a) Inputting a house number and a street name" on page - 2012 Toyota Sienna | Navigation Manual - Page 52
the Point of Interest. 2U5075F 3. Touch the button for the desired method. 2U5023F 2. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 63.) When inputting the - 2012 Toyota Sienna | Navigation Manual - Page 53
the last 5 cities INFORMATION The desired Point of Interest can be displayed on the map screen. (See " - Display POI icons" on page 80.) INFORMATION D To change the selected region, touch "Select Region". D To cancel the city setting, touch "Any City". 50 - 2012 Toyota Sienna | Navigation Manual - Page 54
DESTINATION SEARCH INPUTTING THE CITY NAME 1. Touch "Input City Name". SELECTING FROM THE NEAREST 5 CITIES 1. Touch "Nearest 5 Cities". 2U5027F 2. Input the city name. 2U5029F 2. Touch the button of the desired city name. 2U5028F 3. Touch the button of the desired city name from the displayed - 2012 Toyota Sienna | Navigation Manual - Page 55
SELECTING FROM THE LAST 5 CITIES D Selecting from the categories 2U5077F Touch the button of the desired city name. If the navigation has never been used, no cities will be displayed on the screen. 2U5031F Touch "Category". 2U5032F If the desired POI category is on the screen, touch the name - 2012 Toyota Sienna | Navigation Manual - Page 56
of POIs located within approximately 20 miles (32 km) from the selected search point. 2U5036F 2. Input the city center name. 2U5037F 3. Touch the button of the desired city center name. 2U5038F When an arrow facing the desired point is touched, the map scrolls in that direction. Releasing the - 2012 Toyota Sienna | Navigation Manual - Page 57
DESTINATION SEARCH SETTING THE CURRENT POSITION AS THE SEARCH POINT Touch "Current Position". The search point is set at the current position, and the "POI Category" screen will be displayed. SETTING THE SEARCH POINT VIA THE MAP SCREEN 1. Touch "Map". 2U5039F When an arrow facing the desired - 2012 Toyota Sienna | Navigation Manual - Page 58
DESTINATION SEARCH SETTING THE SEARCH POINT FROM DESTINATIONS 1. Touch the destination buttons at the bottom of the screen. D To search POIs near the search point When the search point is set, the "POI Category" screen will be displayed. 2U5040F When an arrow facing the desired point is touched, - 2012 Toyota Sienna | Navigation Manual - Page 59
will be displayed. 2U5044F By touching the button of the desired item, the screen changes and displays the map location of the selected destination and the route preference. ( To set a memory point as a destination using the phone number, the number must be registered previously. (See page 101.) 56 - 2012 Toyota Sienna | Navigation Manual - Page 60
4. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 63.) INFORMATION The navigation system does not guide in areas where route guidance is unavailable. (See page - 2012 Toyota Sienna | Navigation Manual - Page 61
want to delete. "Delete All": To delete all previous points in the system. 2U5081F 2U5082F The previous starting point and up to 100 previously set screen. 3. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route - 2012 Toyota Sienna | Navigation Manual - Page 62
while driving. However, the cursor cannot be moved. 2U5051F 4. Touch the button of the desired item. After inputting the two intersecting streets, the screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 63.) 59 - 2012 Toyota Sienna | Navigation Manual - Page 63
If the same two streets cross at more than one intersection, the screen changes and displays the menu to select the city name where the streets intersect. , when entering the destination. Freeways and interstates use an "I" (I−405). US highways use the state designation before the number (CA−118 - 2012 Toyota Sienna | Navigation Manual - Page 64
"Coordinates" on the second page of the "Destination" screen. 2U5055F 2U5056F 5. Touch the button of the desired entrance or exit name. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 63.) "Input Name": An - 2012 Toyota Sienna | Navigation Manual - Page 65
set, a list will be displayed on the screen. 5. If more than one destination is set, touch "OK" after deleting the destinations. The system searches for the guidance route again, and displays the entire route. INFORMATION Set destinations can also be deleted by touching "Route". (See " - Deleting - 2012 Toyota Sienna | Navigation Manual - Page 66
3 Type of the route and the distance 4 Distance of the entire route 3. To start guidance, touch "Guide". "3 Routes": To select the desired route from three possible routes. (See page 65.) "Route": To change the route. (See pages 74 and 76.) 1 2 2U5059F 1. When an arrow facing the desired point is - 2012 Toyota Sienna | Navigation Manual - Page 67
change the route before starting INFORMATION D Guidance can be suspended or resumed. (See "Suspending and resuming guidance" on page 90.) D If "Guide" is touched until a beep sounds, demo mode will start. Push the "MAP/VOICE" button to finish Demo mode for a route, the system will avoid routes when - 2012 Toyota Sienna | Navigation Manual - Page 68
DESTINATION SEARCH 3 ROUTES SELECTION INFORMATION D Even if the "Allow Freeway" indicator is dimmed, the route cannot avoid including a freeway in some cases. D If the calculated route includes a trip by ferry, the route guidance shows a sea route. After you travel by ferry, the current vehicle - 2012 Toyota Sienna | Navigation Manual - Page 69
DESTINATION SEARCH 2U5065F 1 2 3 4 5 Time necessary for the entire trip Distance of the entire trip Toll road Freeway Ferry 66 - 2012 Toyota Sienna | Navigation Manual - Page 70
ROUTE GUIDANCE SECTION ROUTE GUIDANCE 3 D Route guidance screen ...68 D Typical voice guidance prompts ...71 D Distance and time to destination ...73 D Setting and deleting destination ...74 Adding destinations ...Reordering destinations ...Deleting destinations ...D Setting route ...Search - 2012 Toyota Sienna | Navigation Manual - Page 71
ROUTE GUIDANCE Route guidance screen During route guidance, various types of guidance screens can be displayed depending on conditions. D Screen layout D During freeway driving During freeway driving, the freeway exit information screen will be displayed. This screen displays the distance to the - 2012 Toyota Sienna | Navigation Manual - Page 72
ROUTE GUIDANCE junction When the vehicle approaches an exit or junction, the guidance screen for the freeway will be displayed. D When approaching a freeway exit or D When approaching an intersection When the vehicle approaches an intersection, the intersection guidance screen will be displayed. - 2012 Toyota Sienna | Navigation Manual - Page 73
ROUTE GUIDANCE D Other screens TURN LIST SCREEN On this screen, the list of turns on the guidance route can be viewed. Touching the turn list. during guidance displays ARROW SCREEN On this screen, information about next turns on the guidance route can be viewed. Touching during guidance displays - 2012 Toyota Sienna | Navigation Manual - Page 74
ROUTE GUIDANCE Typical voice guidance prompts The voice guidance provides various messages as you approach an intersection, or other point where you need to maneuver the vehicle. 4.2 miles 0.25 miles 4.7 miles 0.25 miles +α 3U5120X 3U5119X 1 "Proceed about 4 miles to the traffic circle." "In a - 2012 Toyota Sienna | Navigation Manual - Page 75
−way roads (of opposite directions) is less than 50 feet (15 m) in residential areas or 164 feet (50 m) in non−residential areas. The system announces the approach to the final destination. 1 2 "Your destination is ahead." "You have arrived at your destination. The route guidance is now finished - 2012 Toyota Sienna | Navigation Manual - Page 76
destination. When the vehicle is on the guidance route, the distance measured along the route is displayed. Travel time and arrival time is calculated based on the set vehicle speed information. (See page 109.) However, when the vehicle is not on the guidance route, the distance is the linear - 2012 Toyota Sienna | Navigation Manual - Page 77
destinations and searching again for the routes can be done. - Reordering destinations When more than one destination is set, you can change the arrival order of the destinations. 3U5009F 1. Touch "Route". 3U5012F 1. Touch "Route". 3U5010F 2. Touch "Add". 3. Input an additional destination in - 2012 Toyota Sienna | Navigation Manual - Page 78
ROUTE GUIDANCE - Deleting destinations 4. After selecting the destinations, touch "OK". The system searches for the guidance route again, and displays the entire route. Even if "OK" is not touched, the entire route is displayed automatically within a few - 2012 Toyota Sienna | Navigation Manual - Page 79
. If "No" is touched, the previous screen will return. 5. If more than one destination is set, touch "OK" after deleting the destinations. The system searches for the guidance route again, and displays the entire route. You can designate the route conditions of the route to the destination. 3U5018F - 2012 Toyota Sienna | Navigation Manual - Page 80
route where a delay is caused by road repairs, or an accident, etc. 3U5021F The entire route from the starting point to the destination is displayed. "Guide": To start guidance. "Route": To change a route. (See pages 74 and 76.) 3U5022F 1. Touch "Route". 3U5023F 2. Touch "Detour". 77 - 2012 Toyota Sienna | Navigation Manual - Page 81
": If you touch this button, the system will search for the route based on the traffic congestion information received from XMr NavTraffic. For details, see "XMr NavTraffic" on page 118. 3U5123X This picture shows an example of how the system would guide around a delay caused by a traffic jam - 2012 Toyota Sienna | Navigation Manual - Page 82
A number of choices are provided on the conditions which the system uses to determine the route to the destination. - Starting route "Route". 1. Touch "Route". 3U5026F 3U5029F 2. Touch "Route Preference" to change the conditions that determine the route to the destination. 2. Touch "Start from - 2012 Toyota Sienna | Navigation Manual - Page 83
such as gas stations and restaurants can be displayed on the map screen. You can also set their location as a destination and use them for route Point of Interest, touch this button. Then choose one of the categories. The system will list the points within 20 miles (32 km). (See page 81.) 3U5031F - 2012 Toyota Sienna | Navigation Manual - Page 84
ROUTE GUIDANCE Touch "Other POIs" on the "Display POI icons" screen. When a Point of Interest category is selected from either the limited list or the complete list, the screen will display symbols of those locations on the map screen. D To display the local POI list Points of Interest that are - 2012 Toyota Sienna | Navigation Manual - Page 85
Interest icons on the map screen as a destination and use it for route guidance. 3U5039F 1. Touch "Map View The map will shift so that the icon is centered on the screen and overlaps with the . At the destination is displayed. "Guide": To start guidance. "Route": To change the route. (See pages 74 - 2012 Toyota Sienna | Navigation Manual - Page 86
. However, not all road touching names in the route may appear on the list. If a road changes its name without requiring a turn (such as on a street that runs through two or more cities), the name change will not appear on the list. The street names will be displayed in order from the - 2012 Toyota Sienna | Navigation Manual - Page 87
This feature is available on the map with more detailed map scale than 30 miles (50 km). : To indicate the next destination. : To preview the route to the next destination. : To preview the route to the next destination in fast−forward mode. : To stop the preview. : To review - 2012 Toyota Sienna | Navigation Manual - Page 88
ROUTE GUIDANCE 3U5048F "Record": To start recording the route trace. "Stop": To stop recording the route trace. If you touch "Stop" to display the following screen. 3U5049F Touching "Yes" stops recording and the route trace remains displayed on the screen. Touching "No" stops recording and the - 2012 Toyota Sienna | Navigation Manual - Page 89
ROUTE GUIDANCE 86 - 2012 Toyota Sienna | Navigation Manual - Page 90
ADVANCED FUNCTIONS SECTION ADVANCED FUNCTIONS Descriptions of functions for more effective use 4 D Quick reference ("Menu" screen) ...88 D Quick reference ("Setup" screen) ...89 D Suspending and resuming guidance ...90 D Volume ...91 D User selection ...92 D My places ...94 Registering memory - 2012 Toyota Sienna | Navigation Manual - Page 91
reference ("Menu" screen) The "Menu" screen allows effective use of the navigation system. To display the "Menu" screen, push the "MENU" XMr NavTraffic information...118 7 "Setup" Enables various settings for the navigation system...89, 108 8 "My Places" Enables changes to "Memory points", "Home" - 2012 Toyota Sienna | Navigation Manual - Page 92
"Setup". 4U5170X 1 "Unit of Measurement" The distance units "km" or "miles" can be selected...109 2 "Estimated Travel Time" The system to display the travel time and the arrival time to the destination on the route guidance screen can be set...109 3 "Keyboard Layout" Key layout can be changed - 2012 Toyota Sienna | Navigation Manual - Page 93
...115 12 "Calibration" Adjustment of the current vehicle position mark can be done manually...116 13 "Default" This touch screen button initializes all of the settings...108 14 "?" Function help for the "Setup" screen can be viewed...29 D To suspend guidance U4001SENI 1. Push the "MENU" button - 2012 Toyota Sienna | Navigation Manual - Page 94
Guidance". U4001SENI 1. Push the "MENU" button. 4U5004F 4U5087F The screen will change to the current position map with route guidance. 2. Touch "Volume". 4U5006F To is not needed, touch "OFF" to disable the feature. When selected the number or "OFF" will be highlighted. 3. Touch "OK" to - 2012 Toyota Sienna | Navigation Manual - Page 95
the voice guidance continues even if the navigation screen is changed to other screens. "Adaptive Volume Control": By turning " be highlighted. The system can memorize the following settings for up to three users. D Map direction D Map scale D Map configuration D Guidance mode D Setup D Volume D - 2012 Toyota Sienna | Navigation Manual - Page 96
ADVANCED FUNCTIONS D To register D To change user 4U5008F 1. Touch "Memorize". The confirmation screen will be displayed. 4U5011F Touch "User number". 4U5012F 4U5009F The above message appears, then the map screen will - 2012 Toyota Sienna | Navigation Manual - Page 97
user Points or areas on the map can be registered. The registered points can be used on the "Destination" screen. (See " - Destination search by Home" on page 44, " - Destination search by Quick access" on page 44 and " - Destination search by "Memory"" on page 57.) Registered areas are avoided - 2012 Toyota Sienna | Navigation Manual - Page 98
ADVANCED FUNCTIONS - Registering memory points 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 4U5016F 4U5017F On this screen, the following operations can be performed. 1 Registers memory points (See " - Registering memory points" on page 95.) 2 Edits memory points (See " - - 2012 Toyota Sienna | Navigation Manual - Page 99
ADVANCED FUNCTIONS - Editing memory points The icon, attribute, name, location and/or telephone number of a registered memory point can be edited. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 4U5019F 5. Touch "OK". To edit registered information, see " - Editing memory - 2012 Toyota Sienna | Navigation Manual - Page 100
D To change "Icon" 1. Touch "Icon" on the "Memory Point" screen. 4U5022F 4U5023F 5. Touch the button to be edited. "Icon": To select icons to be displayed on the map. (See page 97.) "Quick Access": To set an attribute. Memory points with a set attribute can be used as a "Quick access" or "Home - 2012 Toyota Sienna | Navigation Manual - Page 101
sound will be heard. 1. Touch "with Sound" on the "Change Icon" screen. D To change "Quick Access" It is possible to change attributes of the quick access points. Memory points with a set attribute can be used as a "Quick Access" or "Home" touch screen button. (See " - Destination search by - 2012 Toyota Sienna | Navigation Manual - Page 102
ADVANCED FUNCTIONS DELETING "Quick Access" D To change "Name" 1. Touch "Name" on the "Memory Point" screen. 4U5028F 4U5030F 1. Touch "Del.". 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch "OK". The previous screen will be displayed. 4U5029F 2. To delete - 2012 Toyota Sienna | Navigation Manual - Page 103
ADVANCED FUNCTIONS DISPLAYING MEMORY POINT NAMES The name of a memory point that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Memory Point" screen. 4U5031F To show the name, touch "ON" on the "Memory Point" screen. To not show it, touch " - 2012 Toyota Sienna | Navigation Manual - Page 104
on the "Menu" screen. 4U5033F 2. Enter the number using number keys. 3. Touch "OK". The previous screen will be displayed. 4U5034F 3. Touch "Delete". 4U5035F 4. Touch the button to be deleted. "Delete All": To delete all memory points in the system. 5. To delete the memory point, touch "Yes". To - 2012 Toyota Sienna | Navigation Manual - Page 105
ADVANCED FUNCTIONS - Registering home If home has been registered, that information can be recalled by using the "Home" touch screen button on the "Destination" screen. (See " - Destination search by Home" on page 44.) 1. Push the "MENU" button. 2. Touch "My Places" on - 2012 Toyota Sienna | Navigation Manual - Page 106
ADVANCED FUNCTIONS - Deleting home 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. - Registering area to avoid Areas you want to avoid because of traffic jams, construction work or other reasons can be registered as areas to avoid. 1. Push the "MENU" button. 2. Touch "My - 2012 Toyota Sienna | Navigation Manual - Page 107
area size of a registered area can be edited. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 4U5043F 7. Touch either or to change the size of the area to be avoided. 8. Touch "OK". 4U5044F 3. Touch "Edit". INFORMATION D If a destination is input in the area to avoid or the - 2012 Toyota Sienna | Navigation Manual - Page 108
ADVANCED FUNCTIONS D To change "Name" 1. Touch "Name" on the "Edit Area to Avoid" screen avoid feature. To turn on the feature touch "ON" on the "Edit Area to Avoid" screen. To turn off the feature touch "OFF" on the "Edit Area to Avoid" screen. 6. Touch "OK". 2. Enter the name using alphanumeric - 2012 Toyota Sienna | Navigation Manual - Page 109
NAMES OF AREAS TO BE AVOIDED The name of an area to be avoided that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Edit Area to Avoid" screen. 4U5048F To show the name, touch "ON" on the "Edit Area to Avoid" screen. To - 2012 Toyota Sienna | Navigation Manual - Page 110
"Edit Area to Avoid" screen. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 4U5049F 4U4051F 3. Touch "Delete". 2. Touch either or to change the size of the area to be avoided. 3. Touch "OK". The previous screen will be displayed. 4U5052F 4. Touch the button to be deleted - 2012 Toyota Sienna | Navigation Manual - Page 111
1. Push the "MENU" button. 4U5054F 4. Touch the button you want to delete. "Delete All": To delete all previous points in the system. 4U5093F 2. Touch "Setup". 4U5094F 4U5055F 3. Touch the items to be set. 5. To delete the point, touch "Yes". To cancel the deletion, touch "No". 4. Touch - 2012 Toyota Sienna | Navigation Manual - Page 112
ADVANCED FUNCTIONS D Unit of Measurement Unit of Measurement can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D Estimated travel time The speed that is used for the calculation of the estimated travel time and the estimated arrival time can be set. 1. Push the " - 2012 Toyota Sienna | Navigation Manual - Page 113
to the destination is the approximate driving time that is calculated based on the selected speeds and the actual position along the guidance to display up to 99 hours 59 minutes. Key layout can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 4U5097F 3. Touch "ABC" or - 2012 Toyota Sienna | Navigation Manual - Page 114
ADVANCED FUNCTIONS LAYOUT TYPE D Time zone Time zone can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 4U5062F " "ABC" type 4U5098F 3. Touch "Change" of "Time Zone". The "Adjust Time Zone" screen will be displayed on the display. 4U5063F " "QWE" type The selected - 2012 Toyota Sienna | Navigation Manual - Page 115
touch screen button and current street name on the map screen can be displayed or hidden. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D POI category change (Display POI Icons) Select from among the 6 icons displayed on the "Display POI Icons" top screen, so that setting of the - 2012 Toyota Sienna | Navigation Manual - Page 116
shape When the "Display Building Shapes" feature is turned on, the system will display the building shape on the map screen using a scale of 150 feet (50 m) to 300 feet (100 m). To turn the "Display Building Shapes" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. to display - 2012 Toyota Sienna | Navigation Manual - Page 117
the Then touch "Setup" screen. D Voice guidance in all modes When the "Voice Guidance in All Modes" feature is turned on, the voice guidance in all modes can be heard. When the "Voice Guidance in All Modes" feature is turned off, voice guidance cannot be heard when using the audio system. To turn - 2012 Toyota Sienna | Navigation Manual - Page 118
the voice guidance can be heard automatically. When the "Auto Voice Guidance" feature is turned off, the voice guidance can be heard only if the "MAP/VOICE" button is pushed. To turn the "Auto Voice Guidance" mode on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. twice to display - 2012 Toyota Sienna | Navigation Manual - Page 119
be adjusted manually. Miscalculation of the distance caused by tire replacement can also be adjusted. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. twice to display page 3 of Then touch the "Setup" screen. 4U5077F This message appears when the system is in the POI mode and the - 2012 Toyota Sienna | Navigation Manual - Page 120
, the current vehicle position mark will be automatically corrected by GPS signals. If GPS reception is poor due to location, you can manually adjust the current vehicle position mark. 3. Touch "Enter". 4U5083F 4U5081F 1. Touch "Position/Direction". 4. Touch either or to adjust the direction of - 2012 Toyota Sienna | Navigation Manual - Page 121
allows the navigation system to display traffic information on the map is available if your satellite radio tuner can receive traffic information. To receive the XMr NavTraffic service, an additional genuine Toyota satellite receiver and antenna must be purchased and installed, and the subscription - 2012 Toyota Sienna | Navigation Manual - Page 122
Traffic information is displayed on the map. (See page 120.) 2 Auto Avoid Traffic If any heavy congestion or moderate traffic has been detected select another route offered by the system. (See page 121.) 3 Traffic Voice Guidance Traffic information is provided using voice guidance. (See page 122.) - 2012 Toyota Sienna | Navigation Manual - Page 123
XMr NavTraffic information has been received, the XMr NavTraffic information arrow will appear on the map screen. The color of the arrow changes depending on the traffic information received. "Orange": Heavy congestion "Yellow": Moderate traffic "Green": Freely flowing traffic 2 4U5110F " Freeway - 2012 Toyota Sienna | Navigation Manual - Page 124
XMr NavTraffic indicator will appear on the screen. The color of the indicator changes depending on the traffic information received. "White": . (b) Auto Avoid Traffic The guidance route automatically changes to another route to avoid heavy congestion. 4U5112F Touch "ON" of the "Auto Avoid Traffic - 2012 Toyota Sienna | Navigation Manual - Page 125
voice guidance while being guided to your destination. (d) Show Free Flowing Traffic Freely flowing traffic is shown with the arrow. 4U5113F Touch "ON" of the "Traffic Voice Guidance". 4U5114F Touch "ON" of the "Show Free Flowing Traffic". INFORMATION This function is available only in English - 2012 Toyota Sienna | Navigation Manual - Page 126
ADVANCED FUNCTIONS (e) XMr NavTraffic text information When you touch the XMr NavTraffic icon on the map, the XMr NavTraffic info. bar will appear on the upper part of the screen. 5U5B03F 1. Touch "Info." to display the "Traffic Information" screen. 5U5B04F 2. Touch "Detail" to display detailed - 2012 Toyota Sienna | Navigation Manual - Page 127
ADVANCED FUNCTIONS 124 - 2012 Toyota Sienna | Navigation Manual - Page 128
OTHER FUNCTIONS SECTION OTHER FUNCTIONS D Maintenance information ...Maintenance information setting ...Dealer setting ...D Calendar with memo ...Adding a memo ...Editing a memo ...Memo list ...D Screen adjustment ... 5 126 126 128 130 132 133 133 135 D Screen setting ...136 D Beep setting ... - 2012 Toyota Sienna | Navigation Manual - Page 129
" - Dealer setting" on page 128.) If "ON" is selected, the system gives maintenance information with the "Information" screen when the system is turned on. (See page 24.) If "OFF" is selected, the "Information" screen is disabled. When the vehicle needs to be serviced, the touch screen button color - 2012 Toyota Sienna | Navigation Manual - Page 130
engine coolant "BRAKE OIL": Replace brake fluid "ATF": Replace ATF (Automatic Transmission Fluid) "SERVICE": Scheduled maintenance "AIR FILTER": Replace air filter "PERSONAL": New information items can be created separately from provided ones. 5U5003F 4. Input the conditions. Notice of "Date - 2012 Toyota Sienna | Navigation Manual - Page 131
setting It is possible to register a dealer in the system. With dealer information registered, route guidance to the dealer is available. 1. Push the "INFO" button. 2. Touch "Maintenance" on the "Information" screen. 3. Touch "Set Dealer" on the "Maintenance" screen. 5U5005F 5. Touch the button - 2012 Toyota Sienna | Navigation Manual - Page 132
OTHER FUNCTIONS D To edit "Dealer" or "Contact" 1. Touch "Dealer" or "Contact" on the "Edit Dealer" screen. D To edit "Location" 1. Touch "Location" on the "Edit Dealer" screen. 5U5006F 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch "OK". The previous - 2012 Toyota Sienna | Navigation Manual - Page 133
edit "Phone #" (telephone number) 1. Touch "Phone #" on the "Edit Dealer" screen. It is possible to enter memos for particular dates on the calendar. The system informs you of the memo entry when the system is turned on. (See page 24.) Memos can also be used for route guidance if the memo has been - 2012 Toyota Sienna | Navigation Manual - Page 134
a memo" on page 132.) "Mark f": To change the color of the mark displayed next to the date. To default the mark color, touch "Delete" on the "Mark color" screen. "Date f": To change the color of the date. To default the date color, touch "Delete" on the "Date color" screen. "Prev. Day": To go to the - 2012 Toyota Sienna | Navigation Manual - Page 135
informs of the memo entry when the system is started on the memo date. (See page 24.) 1. Push the "INFO" button. 2. Touch "Calendar" on the "Information" screen. 3. Touch the date you want to add a memo on the "Calendar" screen. 5U5014F 6. Enter text using the keys. Up to 24 letters can be entered - 2012 Toyota Sienna | Navigation Manual - Page 136
(See page 134.) 5U5017F 5. Touch the item to be edited. "Memo": To edit a memo. (See " - Adding a memo" on page 132.) "Location": To change a registered location. (See " - Adding a memo" on page 132.) "Enter ": To set the registered location as a destination. (See "Starting route guidance" on page - 2012 Toyota Sienna | Navigation Manual - Page 137
delete all the displayed memos. A message will be displayed. 6. To delete, touch "Yes". To cancel the deletion, touch "No". 5U5020F 2. Enter the period using the numeral keys. The period from January 1, 2007 through December 31, 2026 can be set for searching. 3. After setting the period, touch "OK - 2012 Toyota Sienna | Navigation Manual - Page 138
Screen adjustment You can adjust the brightness and contrast of the screen. You can also turn the display off, and change the screen to either day or night mode. D Contrast and brightness adjustment The brightness or contrast of the screen can be adjusted depending on the brightness of your - 2012 Toyota Sienna | Navigation Manual - Page 139
with the headlight switch on, touch "Day Mode" on the adjustment screen for brightness and contrast control. If the screen is set in the day mode with the headlight switch turned on, this condition is memorized in the system even with the engine turned off. 5U5B11F 2. Touch "Screen Setting". 136 - 2012 Toyota Sienna | Navigation Manual - Page 140
(a) Automatic transition You can select a function that enables automatic return to the navigation screen from the audio screen. (b) Switch color You can select the color of the touch screen buttons. 5U5A83F Select "ON" or "OFF" and then touch "OK". "ON": The navigation screen automatically - 2012 Toyota Sienna | Navigation Manual - Page 141
D Maintenance information "off" setting D Memory points D Areas to avoid D Previous points D Route trace D User selection settings This function is available only when the vehicle is not moving. 5U5A85F 1. Touch "Delete personal data". The "Delete personal data" screen appears. 5U5A86F 2. Touch - 2012 Toyota Sienna | Navigation Manual - Page 142
can set a beep sound off. Selecting a language The language of the touch screen buttons, pop−up messages and the voice guidance can be changed. U5001SENI U5001SENI 1. Push the "INFO" button. 1. Push the "INFO" button. 5U5B12F 5U5B02F 2. Touch "Beep Off". "Beep Off" is highlighted. To switch the - 2012 Toyota Sienna | Navigation Manual - Page 143
OTHER FUNCTIONS 5U5B01F 3. Touch "English", "Français" or "Español" to select a language. If a screen other than for the navigation system is displayed, the current screen would change to the "CAUTION" screen by pushing the "MAP/VOICE", "DEST" or "MENU" button. 4. Touch "OK". The language is - 2012 Toyota Sienna | Navigation Manual - Page 144
AUDIO SYSTEM SECTION AUDIO SYSTEM 6 143 147 155 166 D Quick reference ...142 D Using your audio system ...143 Some basics ...Radio operation ...CD player operation ...D Audio remote controls ... D Audio system operating hints ...167 141 - 2012 Toyota Sienna | Navigation Manual - Page 145
details, see pages 155 and 157. "DISC·AUX" button Push this button to turn the CD player and AUX on. For details, see pages 144, 146 and 157. 5 6 3 7 4 side of this button to step up or down the frequency, or to access a desired track or file. For details, see pages 147, 148, 151, 158 - 2012 Toyota Sienna | Navigation Manual - Page 146
AUDIO SYSTEM Using your audio system - - Some basics This section describes some of the basic features of your audio system. Some information may not pertain to your system. Your audio system works when the engine switch is in "ACC" or "ON" position. D Turning the system on and off NOTICE To - 2012 Toyota Sienna | Navigation Manual - Page 147
button to turn on the desired mode. The selected mode turns on immediately. Push these buttons if you want to switch from one mode to another. If the disc is not inserted, the "CD" screen will not appear. 6U5D71aF 6U5D72aF The function buttons for radio and CD player operation are displayed on the - 2012 Toyota Sienna | Navigation Manual - Page 148
treble and bass. A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the volume of one group of sounds while decreasing - 2012 Toyota Sienna | Navigation Manual - Page 149
anything other than discs into the slot. The player is intended for use with 12 cm (4.7 in.) discs only. D AUX adapter The sound of portable audio players connected to the AUX adapter can be enjoyed. Push the "DISC·AUX" button to switch to AUX mode. For details, refer to the "Owner's Manual". 146 - 2012 Toyota Sienna | Navigation Manual - Page 150
your vehicle is equipped with a satellite radio broadcast system, when you push the "AM·SAT" button, step down the station band. Your radio automatically changes to stereo reception when a stereo broadcast is received prevent the weak signal from creating noise. If the signal becomes extremely weak - 2012 Toyota Sienna | Navigation Manual - Page 151
AUDIO SYSTEM D Presetting a station D Selecting a station Tune in the desired station using one of the following methods. and the frequency appears on the touch screen button. Each radio mode can store up to 6 stations. To change the preset station to a different one, follow the same procedure - 2012 Toyota Sienna | Navigation Manual - Page 152
radio ID Each XMr tuner is identified with a unique radio ID. You will need the radio ID when activating XMr service or when reporting a problem. If you select the "CH 000" using the "TUNE·SEEK/TRACK" button, the ID code of 8 alphanumeric characters appears. If you select another channel, display of - 2012 Toyota Sienna | Navigation Manual - Page 153
AUDIO SYSTEM D Listening to satellite radio D Channel category U6005SENI 6U5D80F Touch either "TYPEA" or "TYPE"" to go to the next or previous category. Push the "AM·SAT" - 2012 Toyota Sienna | Navigation Manual - Page 154
AUDIO SYSTEM D Presetting a channel 1. Tune in the desired channel. D Selecting a channel Tune in the desired channel using one of the following methods. button. Each touch screen button can store three SAT channels. To change the preset channel to a different one, follow the same procedure. - 2012 Toyota Sienna | Navigation Manual - Page 155
AUDIO SYSTEM D Displaying the title and name 6U5D82F To scan the currently SCAN" a second time. 6U5D83F When you touch "TEXT", the song/program title and the artist name/feature are displayed. Up to 16 alphanumeric characters can be displayed. (Some information will not be fully displayed.) - 2012 Toyota Sienna | Navigation Manual - Page 156
you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or "CH001". If it does not change automatically, select another channel. Care Center at 1−800−967−2346 (U.S.A.) or ANTENNA NO SIGNAL LOADING OFF AIR Contact the XMr Listener 1−877 - 2012 Toyota Sienna | Navigation Manual - Page 157
SYSTEM NOTICE This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses - 2012 Toyota Sienna | Navigation Manual - Page 158
CDs, CD text, WMA discs and MP3 discs. D Audio CD, CD text ...158 D MP3/WMA disc ...161 For appropriate discs for this changer, see "Audio system operating hints" on page 167. (a) Inserting discs The engine switch must be set at "ACC" or "ON" position. U6006SENI 1. Push the " " button. 155 - 2012 Toyota Sienna | Navigation Manual - Page 159
AUDIO SYSTEM CAUTION D Do not place anything on the opened display, as such items may . NOTICE Do not obstruct the display while it is moving. It could damage your audio system. INFORMATION Under extremely cold conditions, the display may react slowly or operation sound may become louder. 156 - 2012 Toyota Sienna | Navigation Manual - Page 160
and the disc will be ejected. A disc can then be inserted. Push the "DISC·AUX" button if the disc are already loaded in the CD player. The "CD" screen will be displayed. NOTICE If a disc cannot be ejected, do not forcibly take out the disc. Keep pushing the " " button for approximately - 2012 Toyota Sienna | Navigation Manual - Page 161
this screen. U6004SENI "TUNE·SEEK/TRACK" button: Use for a direct access to a desired track. Push " " or " " sides of the "TUNE·SEEK/TRACK" button and repeat it until the desired track number appears on the screen. As you release the button, the CD player will start playing the selected track from - 2012 Toyota Sienna | Navigation Manual - Page 162
. Fast forward: Push " " sides of the "TUNE·SEEK/TRACK" button and hold it to fast forward the disc. When you release the button, the CD player will resume playing from that position. Reverse: Push " " sides of the "TUNE·SEEK/TRACK" button and hold it to reverse the disc. When you release - 2012 Toyota Sienna | Navigation Manual - Page 163
the track and play the track again. To cancel it, touch "RPT" once again. "RAND": Use it for automatic and random selection. While the disc is playing, touch "RAND" briefly. "RAND" appears on the screen. The system selects a track on the disc being listened to in random order. To cancel it, touch - 2012 Toyota Sienna | Navigation Manual - Page 164
AUDIO SYSTEM (e) Operating a MP3/WMA disc D Playing a MP3/WMA disc D Selecting a desired folder "FOLDERY": Touch this button to go to the next folder. "FOLDERB": Touch this button to go to the previous folder. "FOLDER LIST": The desired folder can be selected in a list. This function is available - 2012 Toyota Sienna | Navigation Manual - Page 165
AUDIO SYSTEM D Selecting a desired file 6U5D90aF U6004SENI "FILE": The desired file can be selected in a list. This function is available only when the vehicle is not moving. Touch "FILE". The file list is displayed. "TUNE·SEEK/TRACK" button: Use for direct access to a desired file. Push " " or " - 2012 Toyota Sienna | Navigation Manual - Page 166
file 6U5D91aF Touch the desired file number. The CD player will start playing the selected file from the beginning. is displayed. "DETAIL": Details of the file currently playing is displayed. This function is available only when the vehicle is not moving. 6U5D92aF While the disc is playing, touch " - 2012 Toyota Sienna | Navigation Manual - Page 167
folders are scanned in one pass, normal play resumes. 6U5D64aF "RPT": Use it for automatic repeat of the file or folder you are currently listening "RPT" appears on the screen. When the file is finished, the CD player will automatically go back to the beginning of the file and play the file again - 2012 Toyota Sienna | Navigation Manual - Page 168
appear on the screen. For appropriate discs for this player, see "Audio system operating hints" on page 167. If "CD Error" appears on the display: The following causes are possible. D There is a trouble inside the system. Eject the disc. D The inside of the player unit may be too hot due to the very - 2012 Toyota Sienna | Navigation Manual - Page 169
MODE" switch Each time you push the "MODE" switch, the system changes the audio mode. To turn the audio system on, push the "MODE" switch. To turn the audio system off, push and hold the "MODE seek mode, the seek mode will cancel. CD player Use system can be adjusted with the switches on the - 2012 Toyota Sienna | Navigation Manual - Page 170
for two signals to reach your antenna at the same time. If this player. D The use of a cellular phone inside or near the vehicle may cause a noise from the speakers of the audio system which you are listening to. However, this does not indicate a malfunction. Radio reception Usually, the problem - 2012 Toyota Sienna | Navigation Manual - Page 171
files. To prevent noise and playback errors, use the appropriate file extensions. D The player can play only the first session using multi−session compatible CDs (The system can play MP3 files with sampling frequencies of 16, 22.05, and 24 kHz. However, the emphasis function is not available for - 2012 Toyota Sienna | Navigation Manual - Page 172
AUDIO SYSTEM 6U5161aX the "finalizing process" (a process that allows discs to be played on a conventional CD player) cannot be played. D It may not be possible to play CD− R/CD− insert a CD−RW disc into the MP3/WMA player, playback will begin more slowly than with a conventional CD or CD−R disc. - 2012 Toyota Sienna | Navigation Manual - Page 173
only. D Extremely high temperature can keep your CD player from working. On hot days, use air conditioning to cool the vehicle interior before you listen to a disc. D Bumpy roads or other vibrations may make your CD player skip. D If moisture gets into your CD player, you may not hear any sound even - 2012 Toyota Sienna | Navigation Manual - Page 174
not designed for use of Dual Disc. Do not use Dual Disc because it may cause damage to the player. D If a disc cannot be ejected, do not forcibly take out the disc. Keep pushing the " " button for approximately 5 seconds and release it. At this time, the audio disc and the map DVD−ROM will - 2012 Toyota Sienna | Navigation Manual - Page 175
see a pin hole, hold the disc up to the light.) D Remove discs from the players when you are not using them. Store them in their plastic cases away from moisture line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record - 2012 Toyota Sienna | Navigation Manual - Page 176
AUDIO SYSTEM TERMS Packet write- This is a general term that describes the process of writing data can be viewed when the track is played back. WMA Tag- WMA files can contain a WMA tag that is used in the same way as an ID3 tag. WMA tags carry information such as track title, artist name. ISO 9660 - 2012 Toyota Sienna | Navigation Manual - Page 177
AUDIO SYSTEM 174 - 2012 Toyota Sienna | Navigation Manual - Page 178
REAR VIEW MONITOR SYSTEM SECTION REAR VIEW MONITOR SYSTEM 7 D Rear view monitor system ...176 175 - 2012 Toyota Sienna | Navigation Manual - Page 179
the rear view mirror. To display the rear view image on the screen, the shift lever is in the "R" position when the engine switch is in to check behind and all around the vehicle visually and with mirrors before proceeding. D Do not use the system when the back door is not completely closed. D If - 2012 Toyota Sienna | Navigation Manual - Page 180
changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally. Do not scrub the lens strongly or polish the lens using stiff brushes or abrasive cleansers. Doing so could scratch the lens and affect the image. Do not allow organic solvent, car - 2012 Toyota Sienna | Navigation Manual - Page 181
REAR VIEW MONITOR SYSTEM D Area displayed on screen Image is displayed approximately level on screen. U7002SENI The area displayed on the screen may vary according to vehicle orientation or - 2012 Toyota Sienna | Navigation Manual - Page 182
actual distance. When the camera is used under fluorescent lights, sodium lights, mercury lights etc., the lights and the illuminated areas may appear to flicker. In the following cases, it may become difficult to see the images on the screen, even when the system is functioning. D In the dark (for - 2012 Toyota Sienna | Navigation Manual - Page 183
REAR VIEW MONITOR SYSTEM 180 - 2012 Toyota Sienna | Navigation Manual - Page 184
APPENDIX SECTION APPENDIX 8 D Limitations of the navigation system ...182 D Map database information and updates ...184 181 - 2012 Toyota Sienna | Navigation Manual - Page 185
The installation of window tinting may obstruct the GPS signals. Most window tinting contains some metallic content that will interfere with GPS signal reception of the antenna in the instrument panel. We advise against the use of window tinting on vehicles equipped with navigation systems. 182 - 2012 Toyota Sienna | Navigation Manual - Page 186
change of direction by going forward and backward, or turning on a turntable in the parking lot. D When leaving a covered parking lot or parking garage. D When a roof carrier is installed. D When driving with tire chains installed During auto reroute, the route guidance may not be available for - 2012 Toyota Sienna | Navigation Manual - Page 187
- After replacing a tire, implement the operation described in the "TIRE CHANGE CALIBRATION". (See page 118.) This navigation system uses tire turning data and is designed to work with factory− specified tires for your vehicle. Installing tires that are larger or smaller than the originally equipped - 2012 Toyota Sienna | Navigation Manual - Page 188
for use in the specific system for which it was created. Except to the extent explicitly permitted by mandatory laws, you may not extract or reutilize any portion of the contents of the DATABASE, nor reproduce, copy, duplicate, modify, adapt, translate, disassemble, decompile, or reverse engineer - 2012 Toyota Sienna | Navigation Manual - Page 189
OUT OF THIS AGREEMENT OR YOUR USE OF THE DATABASE, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR COSTS OF COVER, LOSS OF USE OR BUSINESS INTERRUPTION OR THE due to the passage of time, changing circumstances, and due to the nature of the sources used. The DATABASE does not include or reflect - 2012 Toyota Sienna | Navigation Manual - Page 190
law, regulation, or code, including any Sunshine Act, Public Records Act, Freedom of Information Act, or equivalent, which permits public access and/or reproduction or use of the Licensed Products. In the event that such exemption is challenged under any such laws, this Agreement shall be considered - 2012 Toyota Sienna | Navigation Manual - Page 191
. The following trademarks and registrations are owned by the USPS: United States Postal Service, USPS, and ZIP+4. TERMS AND CONDITIONS Personal Use Only. You agree to use this Data together with vehicle navigation system for the solely personal, non−commercial purposes for which you were licensed - 2012 Toyota Sienna | Navigation Manual - Page 192
(a) use this Data with any products, systems, or applications installed or the passage of time, changing circumstances, sources used and the nature of USE THIS INFORMATION, ANY DEFECT IN THE INFORMATION, OR THE BREACH OF THESE TERMS OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED - 2012 Toyota Sienna | Navigation Manual - Page 193
, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. You agree to submit to the Officer, federal government agency, or any federal official refuses to use the legend provided herein, the Contracting Officer, federal government - 2012 Toyota Sienna | Navigation Manual - Page 194
not decompile, disassemble or reverse engineer any portion of this information, and may not transfer or distribute it in any form, for any purpose. Without limiting the foregoing, you may not use this information with any products, systems, or applications installed or otherwise connected to or in - 2012 Toyota Sienna | Navigation Manual - Page 195
. The use of such marks in this product does not imply any sponsorship, approval, or endorsement by such companies of this product. There are two types of areas available for route guidance. In one type of area, primarily around metropolitan centers, detailed route guidance is available for the - 2012 Toyota Sienna | Navigation Manual - Page 196
APPENDIX - Changing the map DVD−ROM U4001SENI 7U5167X 1. Push the "MENU" button. 4. Insert the new map DVD−ROM with the label side up. 5. Push the "CLOSEY" button to close the display. 7U5007F 2. Touch "Map DVD". 7U5008F 3. Touch " DVD−ROM. DVD" to eject the map 193 - 2012 Toyota Sienna | Navigation Manual - Page 197
the display while it is moving. It could damage your navigation system. D If a disc cannot be ejected, do not forcibly take audio disc and the map DVD−ROM will be ejected. 7U5009F 2. Touch "Map DVD". INFORMATION Under extremely cold dealer to find out if there is a more recent update released. 194 - 2012 Toyota Sienna | Navigation Manual - Page 198
APPENDIX D Certification For vehicles sold in Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Category II - 2012 Toyota Sienna | Navigation Manual - Page 199
APPENDIX 196 - 2012 Toyota Sienna | Navigation Manual - Page 200
of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals from the Global Positioning System (GPS) operated by the U.S. Department of Defense. Using these signals and other vehicle sensors, the system indicates your present position and assists - 2012 Toyota Sienna | Navigation Manual - Page 201
SIENNA_Entry_Navi_U OM45469U Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly. The accuracy of the vehicle's position depends on the satellite condition, road configuration, vehicle - 2012 Toyota Sienna | Navigation Manual - Page 202
become thoroughly familiar with it. Read the entire Navigation System Owner's Manual to make sure you understand the system. Do not allow other people to use this system until they have read and understood the instructions in this manual. For your safety, some functions may become inoperable when - 2012 Toyota Sienna | Navigation Manual - Page 203
, etc.) frequently change. Therefore, before following any instruction from the system, look to see whether the instruction can be done safely and legally. This system cannot warn about such things as the safety of an area, condition of streets, and availability of emergency services. If unsure - 2012 Toyota Sienna | Navigation Manual - Page 204
Quick guide - - Overview buttons and guidance screen 0U5111aX No. 1 2 Name North−up or heading−up symbol Scale indicator "MAP/VOICE" button "DEST" button "MENU" button "DISP/TILT" button Function This symbol indicates a map view with north−up or heading−up. Touching this symbol changes the map - 2012 Toyota Sienna | Navigation Manual - Page 205
to display the foot print map and the building information. Touch this button to change the screen mode. Displays the distance, the estimated travel time to the destination, and the estimated XMr NavTraffic mark "GPS" mark (Global Positioning System) 36 37 15 34 16 73 17 118 18 182 6 - 2012 Toyota Sienna | Navigation Manual - Page 206
- Registering home 1 Push "DEST" button. 2 Touch . If home has not been registered, you can register it by touching . 3 There are 11 different methods to search your home. See "Destination search" on page 41. 4 Touch "Enter". The "Memory Point" screen is displayed. 7 - 2012 Toyota Sienna | Navigation Manual - Page 207
5 Touch "OK". Registration of home is complete. You can also register home by touching the "MENU" button. (See " - Registering home" on page 102.) You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 96.) 8 - 2012 Toyota Sienna | Navigation Manual - Page 208
) 1 Push "DEST" button. 2 Touch one of the quick access buttons. You can set a memory point to one of the quick access buttons which has not been set. 3 There are 12 different methods to search preset memory points. See "Destination search" on page 41. 4 Touch "Enter". The " - 2012 Toyota Sienna | Navigation Manual - Page 209
memory points is complete. You can also register preset memory points by touching the "MENU" button. (See " - Registering memory points" on page 95.) You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 96.) The registered points can be - 2012 Toyota Sienna | Navigation Manual - Page 210
There are 12 different methods to search destinations. See "Destination search" on page 41. 3 Touch "Enter". The navigation system performs a search for the route. 4 Touch "Guide", and start driving. Routes other than the one recommended can also be selected. (See "Starting route guidance" on - 2012 Toyota Sienna | Navigation Manual - Page 211
destination 1 Push "DEST" button. 2 Touch . The can be used if your home has been registered. (To register "Home", see " - Registering home" on page 102.) 3 Touch "Enter". The navigation system performs a search for the route. 4 Touch "Guide", and start driving. Routes other than the one - 2012 Toyota Sienna | Navigation Manual - Page 212
D Map screen operation ...Current position display ...Screen scroll operation ...Switching the screens ...Map scale ...Foot print map ...Orientation of the map ...Map icons ...D Speech command system ...33 33 34 39 42 42 43 44 44 Command list ...47 25 - 2012 Toyota Sienna | Navigation Manual - Page 213
BASIC FUNCTIONS Initial screen Vehicles with smart key system - When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the initial screen will be displayed and the system will begin operating. Vehicles without smart key system - When the engine switch is in the "ACC" or "ON" - 2012 Toyota Sienna | Navigation Manual - Page 214
Touch screen operation D Maintenance information This system informs about when to replace certain parts or components and shows dealer information (if registered) on the screen. When the vehicle reaches a previously set driving distance or date specified for a scheduled maintenance check, the - 2012 Toyota Sienna | Navigation Manual - Page 215
can be input via the touch screen. D To input letters and numbers To display the alphabet keys, touch "A−Z". INFORMATION Keyboard layout can be changed. (See page 255.) Enter letters by touching the keys directly. : Touching this button erases one letter. By holding this button, letters will - 2012 Toyota Sienna | Navigation Manual - Page 216
The number of matching items is shown to the right side of the screen. If the number of matching items is more than 999, the system displays "∗∗" on the screen. 29 - 2012 Toyota Sienna | Navigation Manual - Page 217
D List screen operation When a list is displayed, use the appropriate button to scroll through the list. D follows: "Distance": To sort in the order of distance from your current location. "Date": To sort in the order of the date. "Category": To sort in the order of the category. "Icon": To sort in - 2012 Toyota Sienna | Navigation Manual - Page 218
off, and change the screen to either day or night mode. D Contrast, brightness, color and tone adjustment The contrast, brightness, color and tone of the screen, touch "OK". If your vehicle is equipped with the rear seat entertainment system, the rear screen turns on or off when "Rear" is touched. - 2012 Toyota Sienna | Navigation Manual - Page 219
switch, the screen changes to day mode or night mode. Color and tone adjustment (with rear seat entertainment system) You can also use the remote control to make adjustments. 1. Touch the desired button to adjust color and tone. You can adjust the color and the tone while the DVD video and video - 2012 Toyota Sienna | Navigation Manual - Page 220
display When starting the navigation system, the current position is displayed position mark ( 1 ) appears in the center or bottom center of the map screen. A street name will from the GPS (Global Positioning System). If the current position is the system receives signals from the GPS, the - 2012 Toyota Sienna | Navigation Manual - Page 221
can be set as a destination using the one−touch scroll function. Use the scroll feature to move the desired point to the center of the screen for looking at to the center of the screen and the map moves as the vehicle proceeds along the designated route. Touch "Enter ". The screen changes and - 2012 Toyota Sienna | Navigation Manual - Page 222
BASIC FUNCTIONS D To register the cursor position as an address book entry Address book entry registration enables easy access to a specific point. To change the icon or name, etc., see " (b) Editing address book entries" on page 110. Up to 100 address book entries can be registered. If there is - 2012 Toyota Sienna | Navigation Manual - Page 223
BASIC FUNCTIONS D To see information about the icon where the cursor is set POI INFORMATION When the cursor is set on a POI icon, the name and "Info." are displayed at the top of the screen. To display information about an icon, set the cursor on it. Touch "Info.". Information such as the name, - 2012 Toyota Sienna | Navigation Manual - Page 224
BASIC FUNCTIONS INFORMATION The desired Point of Interest can be displayed on the map screen. (See " - Display POI icons" on page 92.) ADDRESS BOOK ENTRY INFORMATION When the cursor is set on an address book entry icon, the name and "Info." are displayed at the top of the screen. Touch "Info.". - 2012 Toyota Sienna | Navigation Manual - Page 225
BASIC FUNCTIONS DESTINATION INFORMATION When the cursor is set on a destination icon, the name and "Info." are displayed on the top of the screen. Information such as the name, address, and phone number are displayed. If "Enter " is touched, the position of the cursor is set as a destination. If - 2012 Toyota Sienna | Navigation Manual - Page 226
BASIC FUNCTIONS - Switching the screens XMr NavTraffic TEXT INFORMATION When you touch the XMr NavTraffic icon on the map, the XMr NavTraffic info. bar will appear on the upper part of the screen. Any one of the screen configurations can be selected . 1. Touch this button to display the following - 2012 Toyota Sienna | Navigation Manual - Page 227
cannot be selected. : To display the single map screen. (See page 40.) : To display the dual map screen. (See page 41.) : To display the compass mode screen. (See page 41.) : To display the freeway screen. (See page 78.) : To display the turn list screen. (See page 80.) : To display the arrow - 2012 Toyota Sienna | Navigation Manual - Page 228
the direction of the destination. INFORMATION When the vehicle travels out of the coverage area, the guidance screen changes to the compass mode screen. This screen can perform the following procedures: 1. Changing the map scale 2. Displaying the POI icon 3. Show XMr NavTraffic Info. (See page 98 - 2012 Toyota Sienna | Navigation Manual - Page 229
m) to 250 miles (400 km). or until the scale bar Touch changes normally. By continuing to touch the button, the scale bar changes smoothly. The scale of the map display can be changed by touching the scale bar directly. It is not available while driving. The map scale is displayed under the north−up - 2012 Toyota Sienna | Navigation Manual - Page 230
BASIC FUNCTIONS - Orientation of the map D To display building information Information is available only for buildings for which information is recorded on the map disc. The orientation of the map can be changed from North−up to Heading−up by touching the orientation symbol at the top left of the - 2012 Toyota Sienna | Navigation Manual - Page 231
FUNCTIONS -Map icons Icon Name Island Park Industry Business facility Airport Military University Hospital Stadium Shopping mall Golf Speech command system- The speech command system enables you to operate the navigation system, audio system and hands−free system by giving a command. 1. Push the - 2012 Toyota Sienna | Navigation Manual - Page 232
on the screen. If a desired outcome is not shown, or if no choices are available, say "Go back" or touch "Go Back" to return to the previous screen. "Cancel", or push and hold the talk switch. If the navigation system does not respond or the confirmation screen does not disappear, please push the - 2012 Toyota Sienna | Navigation Manual - Page 233
Say "Go home". If a home address is not registered, the voice guidance system will say "Your home is not set" and you will be prompted to or touch "Go Back". Touch "Cancel" or say "Cancel", and the speech command system will be canceled. D Voice commands may not be recognized if : D Spoken too - 2012 Toyota Sienna | Navigation Manual - Page 234
a voice recognition command list. You can operate the voice recognition system by saying any command from the displayed command list. However, the XMr NavTraffic commands cannot be used where the XMr NavTraffic service is not available. (For details, see "XMr NavTraffic" page 98.) 1. Push the talk - 2012 Toyota Sienna | Navigation Manual - Page 235
command list can be recognized. D Speech command example: Changing map screen 1. Push the talk switch. 2. Say "Command list". 3. Say "Dual map". To confirm commands on the screen, touch or to scroll through the command list. This function is available only when the vehicle is not moving. When or - 2012 Toyota Sienna | Navigation Manual - Page 236
BASIC FUNCTIONS D Speech command example:Changing map scale 1. Push the talk switch. 2. Say "Command list". 3. Say "Zoom in" or "Zoom out". To confirm commands on the screen, touch or to scroll through the command list. This function is available only when the vehicle is not moving. When or is - 2012 Toyota Sienna | Navigation Manual - Page 237
BASIC FUNCTIONS 50 - 2012 Toyota Sienna | Navigation Manual - Page 238
DESTINATION SEARCH SECTION DESTINATION SEARCH D Destination search ...Selecting the search area ...Destination search by Home ...Destination search by Preset destinations ...Destination search by "Address" ...Destination search by "Point of Interest" ...Destination search by "Previous Destinations" - 2012 Toyota Sienna | Navigation Manual - Page 239
DESTINATION SEARCH Destination search - - Selecting the search area Change the selected region in order to set a destination from a different region by using "Address", "Point of Interest" or "Intersection & Freeway". Push the "DEST" button. 1. Touch "Search Area" to display a map of the United - 2012 Toyota Sienna | Navigation Manual - Page 240
DESTINATION SEARCH U.S.A. Button "US1" "US2" States included in the search region Idaho Oregon Washington California Nevada Arizona Colorado Montana New Mexico Utah Wyoming Iowa Kansas Minnesota Missouri North Dakota Nebraska South Dakota Oklahoma Texas Illinois Indiana Kentucky Michigan Ohio - 2012 Toyota Sienna | Navigation Manual - Page 241
message will be displayed and the setting screen will automatically appear. To use this function, it is necessary to set a "Home" address. preset destination touch screen buttons on the "Destination" screen. The screen changes and displays the map location of the preset destination point and the - 2012 Toyota Sienna | Navigation Manual - Page 242
DESTINATION SEARCH - Destination search by "Address" There are 2 ways to search a destination by address. (a) Search by city (b) Search by street address 1. Push the "DEST" button. 2. Touch "Address" on the "Destination" screen. (a) Selecting a city to search 1. Push the "DEST" button. 2. Touch " - 2012 Toyota Sienna | Navigation Manual - Page 243
Input the street name and touch "OK". 8. Input a house number. 7. When the desired street name is found, touch the corresponding button. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 72.) If the same - 2012 Toyota Sienna | Navigation Manual - Page 244
5 Cities". 3. Touch "Street Address". 2. Touch the button of the desired city name. If the navigation system has never been used, this function will not be available. The current screen changes to the screen for inputting a street name. (See "(a) Selecting a city to search" on page 55.) 4. Touch - 2012 Toyota Sienna | Navigation Manual - Page 245
If the same address exists in more than one city, the current screen changes inputting the city name or to the address list screen. 8. Touch the from the displayed list. INFORMATION You can search for a street name using just the body. Example : S WESTERN AVE You can input "S WESTERN AVE", " - 2012 Toyota Sienna | Navigation Manual - Page 246
of the Point of Interest. 5. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting INFORMATION To search for a facility name using multiple search words, put a space between each word. 59 - 2012 Toyota Sienna | Navigation Manual - Page 247
DESTINATION SEARCH D Selecting a city to search Touch the button of the desired destination. If the same name exists in more than one city, a search can be performed more easily with "City" and "Category". (See "D Selecting a city to search" on page 60 and "D Selecting from the categories" on page - 2012 Toyota Sienna | Navigation Manual - Page 248
search point from near the vehicle's current position 2. Set the search point from along the chosen route 3. Set the search point from near a city center 4. Set the search point from near a destination It is possible to display the names of POIs located within approximately 200 miles (320 km) from - 2012 Toyota Sienna | Navigation Manual - Page 249
POI Category" screen will be displayed. (See page 64.) SETTING THE SEARCH POINT FROM NEAR CITY CENTER 1. Touch "Near City Center". 2. Input the city center name. 3. Touch the button of the desired city center name. The search point is set and the "POI Category" screen will be displayed. (See page - 2012 Toyota Sienna | Navigation Manual - Page 250
DESTINATION SEARCH SELECTING FROM THE LAST 5 CITIES 1. Touch "Near City Center". SETTING THE SEARCH POINT FROM NEAR A DESTINATION 1. Touch "Near a 64.) 3. Touch the button of the desired city center name. The search point is set and the "POI Category" screen will be displayed. (See page 64.) - 2012 Toyota Sienna | Navigation Manual - Page 251
screen, touch "List All Categories" to list all POI categories. 4. Input a telephone number. 5. After inputting a telephone number, touch "OK". The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 72.) If there - 2012 Toyota Sienna | Navigation Manual - Page 252
codes will be displayed. D To set an address book entry as a destination using the phone number, the number must already be registered. (See page 113.) destination. (To delete previous destinations, see page 119.) The screen changes and displays the map location of the selected destination and the - 2012 Toyota Sienna | Navigation Manual - Page 253
Touch "Emergency" on the second page of the "Destination" screen. The display changes to a screen to select police stations, dealers, hospitals or fire stations. While driving, only nearby police stations, dealers, hospitals, or fire stations are shown. The current position is shown with an address - 2012 Toyota Sienna | Navigation Manual - Page 254
4. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 72.) INFORMATION The navigation system does not guide in areas where route guidance is unavailable. (See page - 2012 Toyota Sienna | Navigation Manual - Page 255
the destination to be set. 5. Touch "OK". 8. Touch the button of the desired item. After inputting the two intersecting streets, the screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 72.) 6. Touch the button - 2012 Toyota Sienna | Navigation Manual - Page 256
. If the same two streets cross at more than one intersection, the screen changes and displays the menu to select the city name where the streets intersect. Select 72.) 4. To input a freeway name. Be sure to use the complete name of the freeway or highway, including the hyphen, when entering - 2012 Toyota Sienna | Navigation Manual - Page 257
button. 2. Touch "Map" on the second page of the "Destination" screen. 6. Either a freeway "Entrance" or "Exit" can be selected. The screen changes and displays the map location that was previously displayed just before the destination input operation and the route preference. (See "Starting route - 2012 Toyota Sienna | Navigation Manual - Page 258
Input the latitude and the longitude. 4. When the input is finished, touch "OK". By touching the button of the desired point, the screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 72.) 3. Touch the destination - 2012 Toyota Sienna | Navigation Manual - Page 259
DESTINATION SEARCH Starting route guidance The system searches for the guidance route again, and displays the entire route. After inputting the destination, the screen changes and displays the map location of the selected destination and the route preference. INFORMATION Set destinations can also - 2012 Toyota Sienna | Navigation Manual - Page 260
beep sounds, demo mode will start. Push the "MAP/VOICE" button to finish Demo mode. Current position 2 possible routes. (See page 74.) "Edit Route": To change the route. (See page 75.) 1 D The route traffic congestion. D Route guidance may not be available if there is no road data for the specified - 2012 Toyota Sienna | Navigation Manual - Page 261
DESTINATION SEARCH 3 ROUTES SELECTION 1 1. To select the desired route from 3 routes, touch "3 Routes". 2 3 4 5 Time necessary for the entire trip Distance of the entire trip Toll road Freeway Ferry 2. Touch "Quick", "Alt." or "Short" to select the desired route. "Quick": Recommended route. - 2012 Toyota Sienna | Navigation Manual - Page 262
.) "Delete": To delete destinations. (See page 85.) "Reorder": To reorder destinations. (See page 84.) "Preferences": A number of choices are provided on the conditions which the system uses to determine the route to the destination. (See page 89.) 75 - 2012 Toyota Sienna | Navigation Manual - Page 263
DESTINATION SEARCH 76 - 2012 Toyota Sienna | Navigation Manual - Page 264
ROUTE GUIDANCE SECTION ROUTE GUIDANCE 3 D Route guidance screen ...78 D Typical voice guidance prompts ...81 D Distance and time to destination ...83 D Setting and deleting destinations ...84 Adding destinations ...Reordering destinations ...Deleting destinations ...D Setting route ...Detour - 2012 Toyota Sienna | Navigation Manual - Page 265
ROUTE GUIDANCE Route guidance screen During route guidance, various types of guidance screens can be displayed depending on conditions. D Screen layout D During freeway driving During freeway driving, the freeway exit information screen will be displayed. This screen displays the distance to the - 2012 Toyota Sienna | Navigation Manual - Page 266
ROUTE GUIDANCE D When approaching a freeway exit or junction When the vehicle approaches an exit or junction, the guidance screen for the freeway will be displayed. D When approaching an intersection When the vehicle approaches an intersection, the intersection guidance screen will be displayed. - 2012 Toyota Sienna | Navigation Manual - Page 267
screens TURN LIST SCREEN On this screen, the list of turns on the guidance route can be viewed. Touching ance displays the turn list. during guid- ARROW SCREEN On this screen, information about next turns on the guidance route can be viewed. Touching during guidance displays the arrow screen - 2012 Toyota Sienna | Navigation Manual - Page 268
ROUTE GUIDANCE Typical voice guidance prompts The voice guidance provides various messages as you approach an intersection, or other point where you need to maneuver the vehicle. 4.2 miles 0.5 miles 4.7 miles 0.5 miles 1 2 1 2 3 4 "Proceed about 4 miles to the traffic circle." "In half of a mile - 2012 Toyota Sienna | Navigation Manual - Page 269
−way roads (of opposite directions) is less than 50 feet (15 m) in residential areas or 164 feet (50 m) in non−residential areas. The system announces the approach to the final destination. 1 2 "Your destination is ahead." "You have arrived at your destination. The route guidance is now finished - 2012 Toyota Sienna | Navigation Manual - Page 270
arrow. INFORMATION When the vehicle is on the guidance route, the distance measured along the route is displayed. Travel time and arrival time is calculated based on the set vehicle speed information. (See page 263.) However, when the vehicle is not on the guidance route, the distance is the linear - 2012 Toyota Sienna | Navigation Manual - Page 271
the arrival order of the additional destination. 3. Select the desired destination and press "Move Up" or "Move Down" to change the arrival order. 4. Touch "OK". 5. After selecting the destinations, touch "OK". The system searches for the guidance route again, and displays the entire route. 84 - 2012 Toyota Sienna | Navigation Manual - Page 272
the destination(s), touch "Yes". If "Yes" is touched, the data cannot be recovered. If "No" is touched, the previous screen will return. The system searches for the guidance route again, and displays the entire route. 1. Touch "Route". 2. Touch "Delete". When more than one destination is set - 2012 Toyota Sienna | Navigation Manual - Page 273
route - - Detour setting While the route guidance is operating, you can change the route to detour around a section of the route where a delay the system will calculate an entire new route to the destination. "Around Traffic": If you touch this button, the system will search for the route based on - 2012 Toyota Sienna | Navigation Manual - Page 274
ROUTE GUIDANCE - Route overview 1. Touch "Route". This picture shows an example of how the system would guide around a delay caused by a traffic jam. 1 This position indicates the location of a traffic jam caused by road repairs or an accident. 2 This route indicates the - 2012 Toyota Sienna | Navigation Manual - Page 275
, not all 1. Touch "Route". road names in the route may appear on the list. If a road changes its name without requiring a turn (such as on a street that runs through two or more cities), the name change will not appear on the list. The street names will be displayed in order from the - 2012 Toyota Sienna | Navigation Manual - Page 276
. : To preview the route to the next destination. : To preview the route to the next destination in fast−forward mode. : To stop the preview. : To review the route to the previous destination or starting point. : To review the route to the previous destination or starting point in fast−forward - 2012 Toyota Sienna | Navigation Manual - Page 277
GUIDANCE D To select route features A number of choices are provided on the conditions which the system uses to determine the route to the destination. The entire route from the starting point to the destination is displayed. "OK": To start guidance. "Edit Route": To change a route. (See page 75 - 2012 Toyota Sienna | Navigation Manual - Page 278
To pause guidance 1. Touch "Route". 1. Touch "Route". 2. Touch "Pause Guidance". INFORMATION 2. Touch "Preferences". Without route guidance, Guidance" cannot be used. "Pause 3. Touch "Start from Adjacent Road". When there is no adjacent road, this button will not be displayed. The screen will - 2012 Toyota Sienna | Navigation Manual - Page 279
Interest such as gas stations and restaurants can be displayed on the map screen. You can also set their location as a destination and use them for route on the map screen have already been set, "Change POI" is displayed. The screen will change to the current position map with route guidance. A - 2012 Toyota Sienna | Navigation Manual - Page 280
, touch this button. "Find Local POI": When searching for the nearest Point of Interest, touch this button. Then choose one of the categories. The system will list the points within 200 miles (320 km). (See page 94.) Select the desired POI categories. The selected category icon appears on the top - 2012 Toyota Sienna | Navigation Manual - Page 281
ROUTE GUIDANCE D To display the local POI list Points of Interest that are within 200 miles (320 km) of the current position will be listed from among the selected categories. Select the desired POI categories from the list. The selected category icon appears on the top left of the screen. By - 2012 Toyota Sienna | Navigation Manual - Page 282
of Interest icons on the map screen as a destination and use it for route guidance. "Near Here" : When "Near . The map will shift so that the icon is centered on the screen and overlaps with the . At this the cursor, touch "Enter ". The screen changes and displays the map location of the selected - 2012 Toyota Sienna | Navigation Manual - Page 283
POI icons It is possible to store the traveled route up to 124 miles (200 km) and retrace the route on the display. INFORMATION This feature is available on the map with more detailed map scale than 30 miles (50 km). 1. Touch "Show on Map". 2. Touch "POI Icons". The "POI Icons" indicator - 2012 Toyota Sienna | Navigation Manual - Page 284
ROUTE GUIDANCE D To start recording the route trace D To stop recording the route trace 1. Touch "Show on Map". 1. Touch "Show on Map". 2. Touch "Route Trace". "Route Trace" indicator is highlighted. 2. Touch "Route Trace". The following screen will be displayed. Touching "Yes" stops - 2012 Toyota Sienna | Navigation Manual - Page 285
details about service and activation, call XMr Listener Care Center at 1−800−967−2346 (U.S.A.) or 1−877−209−0079 (CANADA). Customers should have select another route offered by the system. (See page 264.) D Traffic Voice Guidance Traffic information is provided using voice guidance. (See page 260 - 2012 Toyota Sienna | Navigation Manual - Page 286
ROUTE GUIDANCE D Show XMr NavTraffic information XMr NavTraffic information is displayed on the map. 1. Touch "Show on Map". " On Map screen 2. Touch "Traffic Information". "Traffic Information" indicator is highlighted. " On Freeway information screen 99 - 2012 Toyota Sienna | Navigation Manual - Page 287
indicator When any XMr NavTraffic information has been received, the XMr NavTraffic indicator will appear on the screen. The color of the indicator changes depending on the traffic information received. "White": Traffic information has been received. "Yellow": Traffic restriction information on the - 2012 Toyota Sienna | Navigation Manual - Page 288
MY PLACES SECTION MY PLACES D Navigation settings ...Setting up the "Home" ...Setting up the "Preset Destinations" ...Setting up the "Address Book" ...Setting up the "Areas to Avoid" ...Deleting previous destinations ... 4 102 103 105 108 114 119 101 - 2012 Toyota Sienna | Navigation Manual - Page 289
PLACES Navigation settings - Points or areas on the map can be registered. The registered points can be used on the "Destination" screen. (See " - Destination search by Home" on page 54, " 119.) Detailed navigation settings (See page 261.) 1. Push the "SETUP" button. 5 6 2. Touch "Navi.". 102 - 2012 Toyota Sienna | Navigation Manual - Page 290
, that information can be recalled by using the "Go Home" touch screen button on the "Destination" screen. (See "- Destination search by Home" on page 54.) 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. (a) Registering home 1. Push the "SETUP" button. 2. Touch "Navi." on the - 2012 Toyota Sienna | Navigation Manual - Page 291
" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Home" on the "Navigation Settings" screen. 6. Touch "OK". To edit registered information, see "(b) Editing home" on page 104. 4. Touch "Edit". 5. Touch "Edit" for the item you want to change. "Name": To edit home name. The names can be - 2012 Toyota Sienna | Navigation Manual - Page 292
up the "Preset Destinations" (c) Deleting home 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Home" on the "Navigation Settings" screen. If preset destination has been registered, that information can be recalled by using the "Preset Destination" touch screen button on - 2012 Toyota Sienna | Navigation Manual - Page 293
MY PLACES (a) Registering preset destinations 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Preset Destinations" on the "Navigation Settings" screen. When registration of preset destination is completed, the "Edit Preset Destination" screen will be displayed. 7. - 2012 Toyota Sienna | Navigation Manual - Page 294
MY PLACES (b) Editing preset destinations 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Preset Destinations" on the "Navigation Settings" screen. 4. Touch "Edit". 6. Touch "Edit" for the item you want to change. "Name": To edit preset destination names. The names - 2012 Toyota Sienna | Navigation Manual - Page 295
Destinations" on the "Navigation Settings" screen. Points or areas on the map can be registered. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Address Book". 4. Touch "Delete". D Registering address book entries 5. Touch the preset destination for deletion. "Select - 2012 Toyota Sienna | Navigation Manual - Page 296
MY PLACES (a) Registering address book entries 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Address Book" on the "Navigation Settings" screen. 6. Touch "OK". To edit registered information, see "(b) Editing address book entries" on page 110. INFORMATION 4. Touch " - 2012 Toyota Sienna | Navigation Manual - Page 297
number of a registered address book entry can be edited. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Address Book" on the "Navigation Settings" screen. 6. Touch "Edit" for the item you want to change. "Name": To edit address book entry names. The names can be - 2012 Toyota Sienna | Navigation Manual - Page 298
Touch "Edit" of "Icon". 2. Touch the desired sound icon. The next screen appears when "Bell (with Direction)" is touched. 2. Touch the desired icon. Change pages by touching "Page 1", "Page 2" or "With Sound" tab. Touch either or to adjust the direction. Touch "OK". The bell sounds only when - 2012 Toyota Sienna | Navigation Manual - Page 299
MY PLACES D To change "Name" DISPLAYING MEMORY POINT NAMES The name of an address book entry can be set to display on the map. 1. Touch "Edit" of "Name". To show the name, touch "On" on the "Edit Address Book Entry" screen. To not show it, touch "Off". 2. Enter the name using the alphanumeric - 2012 Toyota Sienna | Navigation Manual - Page 300
D To change "Phone #" (telephone number) 1. Touch "Edit" of "Location". 1. Touch "Edit" of "Phone #". 2. Touch one of the 8 directional touch screen buttons to move the cursor to the desired point on the map. 3. Touch "OK". The previous screen will be displayed. 2. Enter the number using number - 2012 Toyota Sienna | Navigation Manual - Page 301
to avoid because of traffic jams, construction work or other reasons can be registered as areas to avoid. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 4. Touch "Delete". 3. Touch "Areas to Avoid". 5. Touch the button to be deleted. "Select All": To select all addresses in - 2012 Toyota Sienna | Navigation Manual - Page 302
(a) Registering areas to avoid 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Areas to Avoid" on area to be avoided. (See "Destination search" on page 52.) 8. Touch either or to change the size of the area to be avoided. 9. Touch "OK". INFORMATION D If a destination - 2012 Toyota Sienna | Navigation Manual - Page 303
SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Areas to Avoid" on the "Navigation Settings" screen. 6. Touch "Edit" for the item you want to change the area to avoid feature. To turn on the feature touch "On" on the "Edit Area to Avoid" screen. To turn off the feature touch "Off" on - 2012 Toyota Sienna | Navigation Manual - Page 304
MY PLACES D To change "Name" DISPLAYING NAMES OF AREAS TO BE AVOIDED The name of an area touch "On" on the "Area to Avoid" screen. To not show it, touch "Off". 2. Enter the name using alphanumeric keys. Up to 32 characters can be entered. 3. Touch "OK". The previous screen will be displayed. 117 - 2012 Toyota Sienna | Navigation Manual - Page 305
to screen button to move the cursor the desired point on the map. 3. Touch "OK". The previous screen will be displayed. 2. Touch either or to change the size of the area to be avoided. 3. Touch "OK". The previous screen will be displayed. 118 - 2012 Toyota Sienna | Navigation Manual - Page 306
Touch "Navi." on the "Setup" screen. 3. Touch "Delete Previous Dest.". 4. Touch "Delete". 5. Touch the button to be deleted. "Select All": To select all registered areas to avoid in the system. "Unselect All": To unselect all registered areas to avoid in the system. 6. Touch "Delete". 7. To delete - 2012 Toyota Sienna | Navigation Manual - Page 307
MY PLACES 6. To delete the destination, touch "Yes". To cancel the deletion, touch "No". 120 - 2012 Toyota Sienna | Navigation Manual - Page 308
TELEPHONE AND INFORMATION SECTION TELEPHONE AND INFORMATION D Telephone (Hands−free system for cellular phone) ...Enter a Bluetooth phone ...Call on the Bluetooth phone ...Receive on the Bluetooth phone ...Talk on the Bluetooth phone ...D Calendar ... 5 122 126 132 139 139 143 121 - 2012 Toyota Sienna | Navigation Manual - Page 309
may be cut. D Noise may be heard on the Bluetoothr audio playback. CAUTION While driving, do not use a cellular phone or connect the Bluetoothr phone. NOTICE Do not leave your cellular phone in the car. The temperature inside may be high and damage the phone. Bluetooth is a registered trademark - 2012 Toyota Sienna | Navigation Manual - Page 310
(Phone Book Access Profile) Ver.1.0 If your cellular phone does not support HFP, you cannot enter the Bluetoothr phone, and take OPP or PBAP service individually. Please go to "http://www.toyota. letstalk.com/" to find approved Bluetoothr phones for this system. You can use the microphone above - 2012 Toyota Sienna | Navigation Manual - Page 311
noise.) D Driving at the high speed. D The window is open. D Turning the air−conditioning vents towards the microphone. D The sound of the air−conditioning left may not be displayed depending on the phone you have. This system doesn't have a charging function. 3 Indicates the receiving area. " - 2012 Toyota Sienna | Navigation Manual - Page 312
or in a place inaccessible by radio waves, "No Service" is displayed. An antenna for the Bluetoothr connection is built in the display. The indication of the Bluetoothr connection may turn yellow and the system may not function when you use the Bluetoothr phone in the following conditions and places - 2012 Toyota Sienna | Navigation Manual - Page 313
undesired operation. CAUTION: Changes or modifications not expressly approved MPE). But it is desirable that it should be installed and operated with at least 20 cm and more with any other antenna or transmitter. To use the hands−free system, you need to enter your phone into the system. Once you - 2012 Toyota Sienna | Navigation Manual - Page 314
screen is displayed. You do not need to enter the phone in case of using the same one. 4. When this screen is displayed, input the passcode displayed on the screen into the phone. For the operation of the phone, see the manual that comes with your cellular phone. If you want to cancel it, touch - 2012 Toyota Sienna | Navigation Manual - Page 315
you register your phone, auto connection will be turned on. Always set it to this mode and leave the Bluetoothr phone in a condition where connection can be established. Vehicles with smart key system- When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, a nearby cellular phone - 2012 Toyota Sienna | Navigation Manual - Page 316
take time, the phone connection is carried out during Bluetoothr audio play. MANUALLY When the auto connection has failed or "Handsfree power" is turned off, you have to connect Bluetoothr manually. 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Connect Phone". 4. Touch "Handsfree - 2012 Toyota Sienna | Navigation Manual - Page 317
TELEPHONE AND INFORMATION When you connect the phone while Bluetoothr audio is playing 5. The "Connect Bluetooth*" screen is displayed. *: Bluetooth is a registered trademark of Bluetooth SIG, Inc. This screen is displayed, and the Bluetoothr audio will stop temporarily. 6. When the connection - 2012 Toyota Sienna | Navigation Manual - Page 318
- If the Bluetoothr phone is disconnected with poor reception from the Bluetoothr network; when the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the system automatically reconnects the Bluetoothr phone. In this case, the connection result is not displayed. Vehicles without smart - 2012 Toyota Sienna | Navigation Manual - Page 319
TELEPHONE AND INFORMATION - Call on the Bluetoothr phone After you enter the Bluetoothr phone, you can call by using hands−free system. You can call using the 6 methods described below. D By dial You can call by inputting the phone number. This cannot be operated while driving. 1. Push the "INFO/ - 2012 Toyota Sienna | Navigation Manual - Page 320
TELEPHONE AND INFORMATION D By phonebook You can call by phonebook data which is transferred from your cellular phone. The system has one phonebook for each telephone. You can register up to 1000 numbers in total of phonebooks. This cannot be operated while driving. 3. Select the - 2012 Toyota Sienna | Navigation Manual - Page 321
AND INFORMATION When the phonebook is empty D By speed dial You can call using registered phone numbers which can be selected from a phonebook. (See "D edit the phonebook. 2. Touch the desired number to call. You can change the page by touching "Speed Dial 2" or "Speed Dial 3" tab. 134 - 2012 Toyota Sienna | Navigation Manual - Page 322
numbers above which were memorized Missed: calls which you missed Incoming: calls which you received Outgoing: numbers which you called You can call using the latest 5 call history items shown by "All" while driving. 3. Touch ing wheel. or push on the steer- 1. Touch "Call History". 2. Select - 2012 Toyota Sienna | Navigation Manual - Page 323
TELEPHONE AND INFORMATION You can call using the latest call history item. on the steering wheel received, the name and the number are displayed. D Number−withheld calls are also memorized in the system. D A international phone call may not be made depending on the cellular phone which you have. - 2012 Toyota Sienna | Navigation Manual - Page 324
the talk switch. "After the beep, please say a command." "Such as "Go Home", "Destination", "Phone", "Audio" or "Command List"." "(beep)" You: "Phone." System: "Phone." "Say a command." "Such as "Dial by Number", "Dial by Name", "Redial", "Call Back" or "Connect Phone"." "(beep)" You: "Dial by Name - 2012 Toyota Sienna | Navigation Manual - Page 325
"Cancel". (Except for recognizing the command.) D By POI* call D Say "Cancel". You can call by touching when it is displayed on the screen from navigation system. (See "POI INFORMATION" on page 36 for details.) *: Point of Interest 138 - 2012 Toyota Sienna | Navigation Manual - Page 326
"+" or use the volume switch change from cellular phone call to Hands−free call, the Hands−free screen will be displayed and you can operate it on the screen. Transferring method and behavior are different depending on the cellular phone which you have. For the operation of the phone, see the manual - 2012 Toyota Sienna | Navigation Manual - Page 327
marked sign (p or w) and the number following phone number. (ex. 056133w0123p#1:) You can do this operation when you want to operate an answering machine or use a telephone service in a bank for example. You can register the phone number and the code number in the phonebook. 140 - 2012 Toyota Sienna | Navigation Manual - Page 328
by giving a command during a call. The operating procedure is similar to other voice recognition. (For the operation of voice recognition, see "Speech command system" on page 44.) When a connected call is interrupted by a third party, this screen is displayed. or push on the steering Touch wheel to - 2012 Toyota Sienna | Navigation Manual - Page 329
wheel during interrupted call, the other party will be switched. If your cellular phone is not approved for HFP Ver. 1.5, this function can not be used. INFORMATION Interrupt call operation may differ depending on your phone company and cellular phone. 142 - 2012 Toyota Sienna | Navigation Manual - Page 330
AND INFORMATION Calendar To view calendar. 1. Push the "INFO/PHONE" button. 2. Touch "Calendar". On this screen, the current date is highlighted in yellow. or or : To change month. : To change year. "Today": To display the current month calendar (if another month's is being displayed). 143 - 2012 Toyota Sienna | Navigation Manual - Page 331
TELEPHONE AND INFORMATION 144 - 2012 Toyota Sienna | Navigation Manual - Page 332
186 212 219 D Quick reference ...146 D Using your audio/video system ...147 Some basics ...Radio operation ...CD changer operation ...Bluetooth audio operation ...DVD player operation ...USB memory/iPod operation ...D Audio/video remote controls ... D Audio/video system operating hints ...221 145 - 2012 Toyota Sienna | Navigation Manual - Page 333
. Function menu tab To control the radio, CD changer, DVD player*, Bluetoothr audio player, AUX or USB memory/iPod, touch the touch−screen tabs access a desired track, file or chapter. For details, see pages 157, 170, 174, 184, 189, 192 and 215. *: Vehicles with rear seat entertainment system 146 - 2012 Toyota Sienna | Navigation Manual - Page 334
the mode switches between FM1 and FM2. For details, see pages 149 and 155. 10 "DISC·AUX" button Push this button to turn the Bluetoothr audio player, AUX, USB memory/iPod, CD changer or DVD player* on. For details, see pages 149, 155, 169, 183 and 188. *: Vehicles with rear seat entertainment system - 2012 Toyota Sienna | Navigation Manual - Page 335
apart or attempt to make any changes yourself. This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disassemble the player or alter any of its - 2012 Toyota Sienna | Navigation Manual - Page 336
screen. See page 252 for details. Push the "DISC·AUX", "FM", "AM" or "SAT" button to turn on the desired mode. U6080GS Push the "AUDIO" button and touch the "AM", "FM", "SAT", "CD", "DVD*", "BT", "AUX" or "USB" tab to turn on the desired mode. *: Vehicles with rear seat entertainment system 149 - 2012 Toyota Sienna | Navigation Manual - Page 337
changer/DVD player* by ejecting all the discs. If the audio system was previously off, then the entire audio system will be turned off when you eject all the discs. If the other function was previously playing, it will come on again. *: Vehicles with rear seat entertainment system U6081GS U6080GS - 2012 Toyota Sienna | Navigation Manual - Page 338
, CD changer, DVD player*, Bluetoothr audio player, AUX and USB memory/ iPod, operation are displayed on the function touch−screen button display screen when the audio control mode is selected. Touch them lightly and directly on the screen. *: Vehicles with rear seat entertainment system Touch the - 2012 Toyota Sienna | Navigation Manual - Page 339
AUDIO/VIDEO SYSTEM (d) DSP the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing difficult to hear due to road noise, wind noise or other noises while driving, select "On". The system adjusts to the optimum volume and - 2012 Toyota Sienna | Navigation Manual - Page 340
screen size (with rear seat entertainment system) 1. Push the "AUDIO" button and touch "DVD" tab. U6007GS 1. Touch Front" or "Rear": Adjusts sound balance between the front and rear speakers. "L" or "R": Adjusts sound balance between the left and right speakers. 3. Touch "OK". The tone of each mode - 2012 Toyota Sienna | Navigation Manual - Page 341
AUDIO/VIDEO SYSTEM U6009GS 4. Touch the desired button. "Normal": Displays a 3 : 4 screen, with either side in black. "Wide the disc. Then it will play from track 1 of the next disc. The changer is intended for use with 4.7 in. (12 cm) discs only. NOTICE D Do not stack up two discs for insertion, - 2012 Toyota Sienna | Navigation Manual - Page 342
AUDIO/VIDEO SYSTEM - Radio operation (h) Your DVD player (with rear seat entertainment system) The sound of the rear seat entertainment system can be enjoyed by pushing the "DISC·AUX" button or touching the "DVD" tab on AUDIO screen. (i) AUX adapter The sound of portable audio players connected to - 2012 Toyota Sienna | Navigation Manual - Page 343
on the touch−screen button. Each radio mode (AM, FM1 or FM2) can store up to 6 stations. To change the preset station to a different one, reduces the amount of channel separation to prevent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to - 2012 Toyota Sienna | Navigation Manual - Page 344
RDS mode provides you to receive text messages from radio stations that utilize RDS transmitters. When RDS is on, the radio can - only select stations of a particular program type, - display messages from radio stations, - search for a stronger signal station. RDS features are available for use only - 2012 Toyota Sienna | Navigation Manual - Page 345
AUDIO/VIDEO SYSTEM U6080GS "Type A "" Each time you touch "A Type " or "Type "", the program type changes as in the following: D ROCK D MISC (Miscellaneous a program is set, "Type Seek" appears. Touch the switch and the system starts to seek the station in the relevant program type. If any type - 2012 Toyota Sienna | Navigation Manual - Page 346
(e) Traffic announcement U6090GSF "Message" If the system receives a radio text from RDS station, "MSG" appears on the display. Touch "Message", and a text message is displayed on the screen. This function is available only when the vehicle is not moving. When you touch "Message Off", the display - 2012 Toyota Sienna | Navigation Manual - Page 347
availability and content of the satellite radio services provided, which are subject to the terms and conditions of the XMr Satellite Radio customer service agreement. Customers radio ID when activating XMr service or when reporting a problem. If you select the "CH 000" using the "TUNE·FILE" knob, - 2012 Toyota Sienna | Navigation Manual - Page 348
AUDIO/VIDEO SYSTEM (c) Listening to satellite radio (d) Channel category U6082GS Touch either "A Type" or "Type "" to go to the next or previous category. Push the "SAT" button or - 2012 Toyota Sienna | Navigation Manual - Page 349
AUDIO/VIDEO SYSTEM (e) Presetting a channel Each touch−screen button can store three SAT channels. To change the preset channel to a different one, follow the same blown fuse. (f) Selecting a channel Tune in the desired channel using one of the following methods. Preset tuning: Touch the channel - 2012 Toyota Sienna | Navigation Manual - Page 350
AUDIO/VIDEO SYSTEM (g) Displaying the title and name U6092GS When you touch "Text", the song/program title and the artist name/feature are displayed. Up to 16 alphanumeric characters can be displayed. (Some information will not be fully displayed.) When you touch "Text" again, the display returns. - 2012 Toyota Sienna | Navigation Manual - Page 351
channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or "CH001". If it does not change automatically, select another channel. Care Center at 1−800−967−2346 (U.S.A.) or NO SIGNAL LOADING OFF AIR −−− Contact the XMr Listener 1−877 - 2012 Toyota Sienna | Navigation Manual - Page 352
SYSTEM NOTICE This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses - 2012 Toyota Sienna | Navigation Manual - Page 353
with smart key system- The "ENGINE START STOP" switch must be in ACCESSORY or IGNITION ON mode. Vehicles without smart key system- The engine switch must be indicators at either side of the slot start blinking again. When the indicators change to green, you can insert the next disc. / CLOSE" but4. - 2012 Toyota Sienna | Navigation Manual - Page 354
Do not obstruct the display while it is moving. It could damage your audio/video system. D Do not insert one disc stacked on top of another one or feed them slot start blinking. After the disc is ejected, the amber indicators change to green. A disc can be inserted. INFORMATION Under extremely cold - 2012 Toyota Sienna | Navigation Manual - Page 355
SYSTEM D All the discs: 3. Remove the disc. The indicators start blinking again and the next disc is ejected. If a disc is not removed within 15 seconds after it is ejected, the operation will be canceled. When all the discs are removed, the amber indicators change map DVD−ROM will be ejected. 168 - 2012 Toyota Sienna | Navigation Manual - Page 356
seat entertainment system - If the DVD player is turned on, push the "DISC·AUX" button again or touch "CD" tab to switch to the CD changer. If the rear seat entertainment system is on, pushing the "DISC·AUX" button switches the sound of the front audio system and that of the rear seat entertainment - 2012 Toyota Sienna | Navigation Manual - Page 357
AUDIO/VIDEO SYSTEM (e) Playing an audio disc U6093GS Push the "AUDIO" button and touch the "CD" tab, then touch the "Change Discs". Choose an audio disc number to display this screen. SELECTING A DESIRED TRACK "SEEK/TRACK" button: Use for direct access to a desired track. Push either side of the - 2012 Toyota Sienna | Navigation Manual - Page 358
AUDIO/VIDEO SYSTEM U6093GS Touch the desired track number. The changer will start playing the selected track from the beginning. : By touching this touch−screen button, the list - 2012 Toyota Sienna | Navigation Manual - Page 359
AUDIO/VIDEO SYSTEM U6094GS OTHER FUNCTIONS "RPT": Use it for automatic repeat of the track or disc you are order - Touch "RAND" briefly while the disc is playing. "RAND" appears on the screen. The system selects a track on the disc being listened to in random order. To cancel it, touch "RAND" - 2012 Toyota Sienna | Navigation Manual - Page 360
VIDEO SYSTEM (f) Playing a MP3/WMA disc SELECTING A DESIRED FOLDER U6095GS Push the "AUDIO" button and touch the "CD" tab, then touch the "Change Discs". : The desired folder can be selected in a list. This function is available only when the vehicle is not moving. Touch "Select". The folder list - 2012 Toyota Sienna | Navigation Manual - Page 361
AUDIO/VIDEO SYSTEM SELECTING A DESIRED FILE "SEEK/TRACK" button: Use for direct access to a desired file. Push either side disc. When you release the button, the changer will resume playing. "TUNE·FILE" knob: Use for direct access to a desired file in the disc. Turn the "TUNE·FILE" knob to step up - 2012 Toyota Sienna | Navigation Manual - Page 362
AUDIO/VIDEO SYSTEM U6095GS "Select" for File: The desired file can be selected in a list. This function is available only when the vehicle is not moving. Touch "Select". The file list is displayed. U6027GS Touch the desired file number. The changer will start playing - 2012 Toyota Sienna | Navigation Manual - Page 363
AUDIO/VIDEO SYSTEM U6096GS SEARCHING FOR A DESIRED FILE Touch "SCAN" on the screen briefly while the disc is playing. "SCAN" appears on the screen. The changer will play - 2012 Toyota Sienna | Navigation Manual - Page 364
AUDIO/VIDEO SYSTEM U6098GS OTHER FUNCTIONS "RPT": Use it for automatic repeat of the file or folder you are order - Touch "RAND" briefly while the disc is playing. "RAND" appears on the screen. The system selects a file in the folder you are currently listening to. To cancel it, touch "RAND" once - 2012 Toyota Sienna | Navigation Manual - Page 365
be read or the system has trouble. Push the " operate, have it checked by your dealer. If an MP3/WMA disc contains system enables users to enjoy music played on a portable player from the vehicle speaker via wireless communication. U6086GS This audio system supports Bluetoothr, a wireless data system - 2012 Toyota Sienna | Navigation Manual - Page 366
find approved Bluetoothr phones for this system. Bluetooth is a trademark owned by Bluetooth SIG. Inc. CAUTION Do not operate the player's controls or connect to the Bluetoothr audio system while driving. NOTICE Do not leave your portable player in the car. In particular, high temperatures inside - 2012 Toyota Sienna | Navigation Manual - Page 367
connection may turn yellow and the system may not function when you use the Bluetoothr portable player in the following conditions. D Your portable player is hiding behind from the display (behind the seat or in the glove box or console box). D Your portable player touches or is covered with metal - 2012 Toyota Sienna | Navigation Manual - Page 368
is in either ACCESSORY or IGNITION ON mode. Vehicles without smart key system- When the portable player is standby for the connection, it will be automatically connected whenever the engine switch is in either "ACC" or "ON" position. D When the auto connection is off Manually connect the portable - 2012 Toyota Sienna | Navigation Manual - Page 369
the portable player, see the instruction manual that comes with it. Touch "Connect". U6033GS Touch "Connect". When the connection is completed, this screen is displayed. Now you can use the portable player. U6035GS Connect the portable audio player to the Bluetoothr audio system. U6034GS This - 2012 Toyota Sienna | Navigation Manual - Page 370
the Bluetoothr network when the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the system automatically reconnects the portable player. In this case, the connection result is not displayed. Vehicles without smart key system- If the portable player is disconnected with poor reception - 2012 Toyota Sienna | Navigation Manual - Page 371
depending on the type of portable player. "SEEK/TRACK" button: Use for direct access to a desired track. Push player. When you release the button, the player will resume playing. INFORMATION Depending on the portable player that is connected to the system, certain functions may not be available - 2012 Toyota Sienna | Navigation Manual - Page 372
Album B": Touch this button to go to the previous album. U6086GS INFORMATION Depending on the portable player that is connected to the system, certain functions may not be available. "RPT": Use this control to automatic replay the track you are currently listening to. Repeating a track- While the - 2012 Toyota Sienna | Navigation Manual - Page 373
disc only when a disc is loaded in the DVD player. A WMA and DVD audio disc cannot be played. For details of "Rear seat entertainment system", refer to "Owner's Manual". For appropriate discs for this player, see "Audio/video system operating hints" on page 221. (a) Inserting the disc INFORMATION - 2012 Toyota Sienna | Navigation Manual - Page 374
inserted, "Check disc" will also appear on the screen. For appropriate discs for this player, see "Audio/video system operating hints" on page 221. Push the " " button. NOTICE Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot. 187 - 2012 Toyota Sienna | Navigation Manual - Page 375
. Push the "DISC·AUX" button or push the "AUDIO" button to display audio screen and touch the "DVD" tab if a disc is already loaded in the player. "DVD" appears on the screen. (If the CD changer is turned on, push the "DISC·AUX" button again or touch "DVD" tab to switch to the DVD player.) 188 - 2012 Toyota Sienna | Navigation Manual - Page 376
beginning. SELECTING A DESIRED TRACK "SEEK/TRACK" button: Use for direct access to a desired track. Push either side of the "SEEK/TRACK" button and repeat it until the desired track number appears on the display. As you release the button, the player will start playing the selected track from the - 2012 Toyota Sienna | Navigation Manual - Page 377
the track and play the track again. To cancel it, touch "RPT" once again. "RAND": Use it for automatic and random selection of the disc which you are currently listening to. When "RAND" is touched, the system selects a track in the disc you are currently listening to. To cancel it, touch "RAND - 2012 Toyota Sienna | Navigation Manual - Page 378
"AUDIO" button and touch the "DVD" tab to display this screen. SELECTING A DESIRED FOLDER U6045GS Touch the desired folder number. The player will start playing the first file in a list. This function is available only when the vehicle is not moving. Touch "Select". The folder list is displayed. - 2012 Toyota Sienna | Navigation Manual - Page 379
SELECTING A DESIRED FILE "SEEK/TRACK" button: Use for direct access to a desired file. Push either side of the "SEEK/TRACK" button and repeat it until the desired file number appears on the display. As you release the button, the player will start playing the selected file from the beginning - 2012 Toyota Sienna | Navigation Manual - Page 380
list is displayed, the top page is displayed. U6106GS SEARCHING FOR A DESIRED FILE Touch "SCAN" on the screen briefly. "SCAN" appears on the screen. The DVD player will play the next file in the folder for 10 seconds, then scan again. To select a file, touch "SCAN" on the screen a second time. If - 2012 Toyota Sienna | Navigation Manual - Page 381
until the beep sounds. "FLD.SCAN" appears on the screen. The DVD player will play the file at the beginning of each folder for 10 seconds, are scanned in one pass, normal play resumes. U6108GS OTHER FUNCTIONS "RPT": Use it for automatic repeat of the file or folder you are currently listening to - 2012 Toyota Sienna | Navigation Manual - Page 382
properly. Be sure to read the instruction manual for the DVD video disc separately provided. For the detailed information about DVD video discs, see "(i) DVD player and DVD video disc information" on page 210. Precautions on DVD video disc When recording with a DVD video or video CD, audio tracks - 2012 Toyota Sienna | Navigation Manual - Page 383
mind when you adjust the volume. U6077GS Vehicles with smart key system- This screen appears when the video screen is first displayed after "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system- This screen appears when the video screen is first displayed - 2012 Toyota Sienna | Navigation Manual - Page 384
/VIDEO SYSTEM U6084GS PLAYING A DVD DISC Push the "AUDIO" button and touch the "DVD" tab to display this screen. Touch "Settings" on "DVD" screen and touch "Wide" on "Settings" screen. The screen mode can be changed. If you touch "Full Screen" when the vehicle is completely stopped and the parking - 2012 Toyota Sienna | Navigation Manual - Page 385
from there. "Audio": The audio changing screen appears. (See page 201.) "Subtitle": The subtitle changing screen appears. (See page 200.) "Angle": The angle selection screen appears. (See page 201.) "Wide": The screen mode screen appears. (See page 153.) U6084GS DISPLAYING DVD CONTROLS If you touch - 2012 Toyota Sienna | Navigation Manual - Page 386
frame during pause. U6052GS U6053GS SELECTING A MENU ITEM Enter the menu item using , , and and touch "Enter". The player starts playing video for that menu item. (For details, see the manual that comes with the DVD video disc provided separately.) Each time you touch "Move Buttons", the controls - 2012 Toyota Sienna | Navigation Manual - Page 387
and touch "OK". The player starts playing video for that title number. When you push either side of the "SEEK/ TRACK" button, you can select a chapter. If you enter the wrong numbers, touch to delete the numbers. When you touch screen returns. , the previous CHANGING THE SUBTITLE LANGUAGE Each time - 2012 Toyota Sienna | Navigation Manual - Page 388
AUDIO/VIDEO SYSTEM U6069GSb CHANGING THE AUDIO LANGUAGE Each time you touch "Change", the language is selected from the ones stored in the discs and changed. When you touch screen returns. , the previous U6076GS CHANGING THE ANGLE The angle can be selected for discs that are multi−angle compatible - 2012 Toyota Sienna | Navigation Manual - Page 389
AUDIO/VIDEO SYSTEM D Audio language You can change the audio language. 1. Touch "Audio Language". 2. Touch the "Setup Menu" screen, . touch the D DVD language You can change the language on the DVD video menu. 1. Touch "DVD Language". 2. Touch the language you want to read on the "DVD Language" - 2012 Toyota Sienna | Navigation Manual - Page 390
SYSTEM alternately. D Parental lock The level of viewer restrictions can be changed. 1. Touch "Parental Lock". 2. Enter the 4−digit personal Setup Menu" screen. ENTER AUDIO LANGUAGE CODE U6059GS If you touch "Other" on the "Select Audio Language" screen, "Select Subtitle Language" screen or "DVD - 2012 Toyota Sienna | Navigation Manual - Page 391
AUDIO/VIDEO SYSTEM 0106 0113 0118 0119 0125 0126 0201 0205 0207 0208 0209 0214 0215 0218 0301 0315 0319 0325 0401 0426 0515 0520 0521 0601 0609 - 2012 Toyota Sienna | Navigation Manual - Page 392
AUDIO/VIDEO SYSTEM 1315 1318 1319 1320 1325 1401 1405 1415 1503 1513 1518 1601 1612 1619 Slovak Slovenian Samoan Shona Somali Albanian Serbian Siswati 1920 1921 1923 2001 2005 2007 2008 2009 2011 2012 2014 2015 2018 2019 2020 2023 2111 2118 2126 2209 2215 2315 2408 2515 2621 Sesotho Sundanese - 2012 Toyota Sienna | Navigation Manual - Page 393
from the front seat. To lock the operation of the player from the rear seat, see "D Rear system lock" on page 254. U6110GS PLAYING A VIDEO CD Push the "AUDIO" button and touch the "DVD" tab to display this screen. When you touch "Wide" on "Settings" screen, the screen mode can be changed. If you - 2012 Toyota Sienna | Navigation Manual - Page 394
AUDIO/VIDEO SYSTEM U6062GS DISPLAYING VIDEO CD SETTINGS If you touch "Settings" on "DVD" screen, "Settings" screen appears. touch this while the player is playing video, the next track is searched and played. "Main/Sub": A multiplex transmission changing control. The mode changes from Main/Sub to - 2012 Toyota Sienna | Navigation Manual - Page 395
SYSTEM DISPLAYING VIDEO CD CONTROLS If you touch the part where controls are not located while you are watching video on the video CD, video CD controls will appear. If " " appears on the display when you touch a control, the operation is not permitted. DESCRIPTION CONTROLS OF VIDEO CD : Use - 2012 Toyota Sienna | Navigation Manual - Page 396
properly. If "DVD error" appears on the display: It indicates that the inside of the player unit may be too hot due to the very high ambient temperature. Remove the disc from the player and allow the player to cool down. If the malfunction is not rectified: Take your vehicle to your dealer. If an - 2012 Toyota Sienna | Navigation Manual - Page 397
SYSTEM (i) DVD player and DVD video disc information DVD VIDEO DISCS This DVD player conforms to NTSC color TV formats. The DVD video disc conforming to another formats such as PAL or SECAM cannot be used. Region codes: Some DVD video discs have a region code indicating a country where you can use - 2012 Toyota Sienna | Navigation Manual - Page 398
to the picture is changed depending on the picture format has also been adopted. Audio data is stored using PCM and Dolby digital, which enables higher quality of sound. Furthermore, multi−angle and multi−language features will also help you enjoy the more advanced technology of DVD video. Viewer - 2012 Toyota Sienna | Navigation Manual - Page 399
player in the car. In particular, high temperatures inside the vehicle may damage the portable player. D Do not push down on or apply unnecessary pressure to the portable player Open the cover and connect a USB memory or iPod using an iPod cable. Turn on the power of the USB memory or iPod if it - 2012 Toyota Sienna | Navigation Manual - Page 400
(and the contents have not been changed), the USB memory will resume play from the same point in which it was last used. D Depending on the iPod or USB memory that is connected to the system, certain functions may not be available. 2. Select the desired play mode. U6079GS 1. Touch "Menu". 213 - 2012 Toyota Sienna | Navigation Manual - Page 401
" for Folder: The desired folder can be selected in a list. This function is available only when the vehicle is not moving. Touch "Select". The folder list is displayed. Touch the desired folder number. The player will start playing the first file of the selected folder. : By touching this touch - 2012 Toyota Sienna | Navigation Manual - Page 402
Reverse: Push and hold the " " side of the "SEEK/ TRACK" button to reverse the player. When you release the button, the player will resume playing. "TUNE/FILE" knob: Use for direct access to a desired file or track in the player. Turn the "TUNE/FILE" knob to step up or down all the files or tracks - 2012 Toyota Sienna | Navigation Manual - Page 403
AUDIO/VIDEO SYSTEM U6078GS " USB memory Touch the desired file or track number. The "Select" for File or Track: The desired file or track can be selected in a list. This function is available only when the vehicle is not moving. Touch "Select". The file or track list is displayed. ton, the list - 2012 Toyota Sienna | Navigation Manual - Page 404
the screen briefly while the music is playing. "SCAN" appears on the screen. The player will play the next file for 10 seconds, then scan again. To select a file, touch "SCAN" on the screen a second time. If the player reaches the end of the memory, it will continue scanning at file1. After - 2012 Toyota Sienna | Navigation Manual - Page 405
U6079GS " iPod "RPT": Use this control to automatic replay the file or track you are currently listening to. Repeating a file or track- While the file or track is playing, touch "RPT" briefly. "RPT" appears on the screen. When the file or track is finished, the player will automatically play it - 2012 Toyota Sienna | Navigation Manual - Page 406
" " or " " switch until you hear a beep to change to the next or the previous disc. Repeat this operation until system can be adjusted using the switches on the steering wheel. Details of the specific switches, controls, and features are described below. 1 Volume control switch 2 " " switch 3 "MODE - 2012 Toyota Sienna | Navigation Manual - Page 407
AUDIO/VIDEO SYSTEM Vehicles with rear seat entertainment system - DVD player While the DVD player is in operation, the chapter or track can be changed by pushing the " " or " " switch. Bluetoothr audio player Use this switch to skip up or down to a different track or album in either direction. To - 2012 Toyota Sienna | Navigation Manual - Page 408
for two signals to reach your antenna at the same time. If this DVD player. D The use of a cellular phone inside or near the vehicle may cause a noise from the speakers of the audio system which you are listening to. However, this does not indicate a malfunction. RADIO RECEPTION Usually, a problem - 2012 Toyota Sienna | Navigation Manual - Page 409
. CAUTION CD changer and DVD player use an invisible laser beam which could cause hazardous radiation exposure if directed outside the unit. Be sure to operate the changers and players correctly. Depending on differences between models or software versions etc., some models listed above might be - 2012 Toyota Sienna | Navigation Manual - Page 410
as shown above. The following products may not be playable on your changer. Copy−protected CD CD−ROM Video CDs DVD player D Use only discs marked as shown above. The following products may not be playable on your player. SACD Copy−protected CD CD−ROM DVD−R DVD+R DVD−RW DVD+RW DVD−ROM DVD−RAM 223 - 2012 Toyota Sienna | Navigation Manual - Page 411
use of such disc may damage the player or changer, or it may be impossible to eject the disc. D If a disc cannot be ejected, do not forcibly take out the disc. Keep pushing the "LOAD· /CLOSE" button for approximately 5 seconds and release it. At this time, the audio disc and the map DVD - 2012 Toyota Sienna | Navigation Manual - Page 412
see a pin hole, hold the disc up to the light.) D Remove discs from the players when you are not using them. Store them in their plastic cases away from moisture line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record - 2012 Toyota Sienna | Navigation Manual - Page 413
noise and playback errors, use the appropriate file extensions. D The player can play only the first session using multi−session compatible CDs. D MP3 player function is available only when playing MP3/WMA files recorded at 32, 44.1 and 48 kHz. Sampling frequency MP3 files for MP3 player: MPEG 1 - 2012 Toyota Sienna | Navigation Manual - Page 414
with no more than two levels of folders. 001.mp3 002.mp3 6U5161aX Folder 3 006.mp3 MP3 player (rear seat entertainment system) Folder 1 003.mp3 Folder 2 004.mp3 005.mp3 001.mp3 002.wma 6U5161aX Folder 3 006.mp3 MP3/WMA player (front audio system) Folder 1 003.mp3 Folder 2 004.mp3 005.wma 227 - 2012 Toyota Sienna | Navigation Manual - Page 415
player (rear seat entertainment system)-It is possible to play up to 253 folders on one disc. D MP3/WMA player (front audio system)-It is possible to play up to 192 folders or 255 files on one disc. D USB memory-It is possible to play up to 999 folders or 255 files per folder. D The order changes - 2012 Toyota Sienna | Navigation Manual - Page 416
AUDIO/VIDEO SYSTEM TERMS Packet write- This is a general term that describes the process of writing can be viewed when the track is played back. WMA Tag- WMA files can contain a WMA tag that is used in the same way as an ID3 tag. WMA tags carry information such as track title, artist name. ISO 9660 - 2012 Toyota Sienna | Navigation Manual - Page 417
AUDIO/VIDEO SYSTEM 230 - 2012 Toyota Sienna | Navigation Manual - Page 418
REAR VIEW MONITOR SYSTEM SECTION REAR VIEW MONITOR SYSTEM 7 D Rear view monitor system ...232 231 - 2012 Toyota Sienna | Navigation Manual - Page 419
and all around the vehicle visually and with mirrors before proceeding. Do not use the system when the backdoor is not completely closed. In the evening, or in other situations with no light sources, the sides may not be visible in wide mode. Use your own eyes to confirm the vehicle's surroundings - 2012 Toyota Sienna | Navigation Manual - Page 420
solvent, car wax, window cleaner or glass coat to adhere to the camera. If this happens, wipe it off as soon as possible. When replacing the tires, please consult your Toyota dealer. If you replace the tires, the position of the guide lines displayed on the screen may change. D D D D D 233 - 2012 Toyota Sienna | Navigation Manual - Page 421
REAR VIEW MONITOR SYSTEM D Area displayed on screen Image is displayed approximately level on screen. On screen On screen Corners of bumper Corners of bumper " Wide mode The area detected by the camera is limited. The camera does not detect objects close to either corner of the bumper or under - 2012 Toyota Sienna | Navigation Manual - Page 422
REAR VIEW MONITOR SYSTEM D The rear view monitor system camera Area displayed on the screen may vary according to vehicle status or road conditions. 235 - 2012 Toyota Sienna | Navigation Manual - Page 423
system camera is located on the back door as shown in the illustration. The camera uses a special lens. The perceived distance from images that appear on the screen differs from the actual distance. When the camera is used under fluorescent lights, sodium lights, mercury lights etc., the lights - 2012 Toyota Sienna | Navigation Manual - Page 424
that the parking space will accommodate your vehicle before maneuvering into it. (a) To activate the rear view monitor system CAUTION Depending on the circumstances of the vehicle (number of passengers, amount of luggage, etc.), the position of the guide lines displayed on the screen may change. Be - 2012 Toyota Sienna | Navigation Manual - Page 425
or regular mode Regular mode and wide mode are switched when the wide/regular mode selection switch is touched. The current mode is indicated by the yellow indicator. (c) The modes of the rear view monitor system The rear view monitor system has the following three modes. Use each mode according to - 2012 Toyota Sienna | Navigation Manual - Page 426
REAR VIEW MONITOR SYSTEM D Estimated course line display 1 2 3 4 Wide/regular mode select switch Touching this button changes between regular mode and wide mode. (See page 238.) Vehicle width extension guide lines These lines indicate the estimated vehicle width extension. When the steering - 2012 Toyota Sienna | Navigation Manual - Page 427
SYSTEM D Guide line display mode D Course line deletion mode Wide/regular mode select switch Touching this button changes between regular mode and wide mode. (See page 238.) 2 Vehicle width extension guide lines These lines indicate the estimated vehicle width extension. 3 Parking assist guide - 2012 Toyota Sienna | Navigation Manual - Page 428
REAR VIEW MONITOR SYSTEM - Driving precautions In any of the following situations, there is a margin of error between the guide lines on the screen and the actual distance/course on the road. D When the grade behind the vehicle slopes up sharply, objects appear to be - 2012 Toyota Sienna | Navigation Manual - Page 429
REAR VIEW MONITOR SYSTEM D When any part of the vehicle sags due to the number of passengers or the distribution of the load, there is a margin of error between the guide lines on the screen and the actual distance/course on the road. D When the grade behind the vehicle slopes down sharply, - 2012 Toyota Sienna | Navigation Manual - Page 430
SYSTEM A . On the screen, it appears that a truck is parking about 1.5 ft. (0.5 m) away. However, in reality if truck. Estimated course line display mode-The estimated course lines are objects (such as vehicles) using the estimated course. In if you back up as guided by the lines, the vehicle - 2012 Toyota Sienna | Navigation Manual - Page 431
line display mode D Example of how to use the system when parking (perpendicular parking) 1. Put the shift lever in the "R" position. If any other display mode is selected, switch to estimated course line display mode. 2. While referring to the screen and mirrors, back into the parking space. The - 2012 Toyota Sienna | Navigation Manual - Page 432
REAR VIEW MONITOR SYSTEM 3. Turn the steering wheel so that the estimated course lines are within the parking space, and back up carefully. 4. When the rear of the vehicle is within the parking space, turn the steering wheel in order to equalize the left and right intervals between the vehicle - 2012 Toyota Sienna | Navigation Manual - Page 433
REAR VIEW MONITOR SYSTEM - Guide line display mode D Example of how to use the system when parking (perpendicular parking) 5. When the vehicle width extension lines and the parking space side lines are parallel, straighten the steering wheel (straight backward position) and then carefully back up - 2012 Toyota Sienna | Navigation Manual - Page 434
turn the steering wheel depends on the width of the parking space. 4. When the vehicle is in the parking space, turn the steering wheel so that the vehicle width extension guide lines and the clearance to the left and right of the parking space are about the same near the vehicle. Back up slowly - 2012 Toyota Sienna | Navigation Manual - Page 435
REAR VIEW MONITOR SYSTEM 5. Turn the steering wheel so that the vehicle width extension guide lines are parallel with the parking space lines. When the lines are parallel, straighten the steering wheel and back up slowly. Even if the distance guide line and the parking space rear edge appear to be - 2012 Toyota Sienna | Navigation Manual - Page 436
initializing" will be displayed If the message "System initializing" will be displayed on the screen, the help screen is touched. Make a appears when correction using the following method in accordance with the display the above screen remains, have the vehicle inspected at your Toyota dealer. 249 - 2012 Toyota Sienna | Navigation Manual - Page 437
REAR VIEW MONITOR SYSTEM 250 - 2012 Toyota Sienna | Navigation Manual - Page 438
SETUP SECTION SETUP 8 D General settings ...252 (Used for language selection and the on/off settings of operation sounds and automatic screen change.) D Clock settings ...257 (Used for changing (Settings are available for portable audio devices and Bluetoothr audio devices players.) D Vehicle - 2012 Toyota Sienna | Navigation Manual - Page 439
"SETUP" button. On this screen, the following functions can be performed. No. 1 Function You can change the language. (See "D Selecting a language" on page 253.) Rear system lock* can be set to "On" or "Off". (See "D Rear system lock" on page 254.) * : Vehicles with rear seat entertainment system - 2012 Toyota Sienna | Navigation Manual - Page 440
SETUP No. 5 Function Line color can be changed. (See "D Selecting the line color" on page 254.) Keyboard layout can be changed. (See "D Selecting a keyboard layout" on page 255.) Distance unit can be changed. (See "D Unit of measurement" on page 255.) The personal data can be deleted. (See "D - 2012 Toyota Sienna | Navigation Manual - Page 441
be changed. 1. Push the "SETUP" button. 2. Touch "General" on the "Setup" screen. 3. Touch "Line Color". 3. Touch "Rear System Lock". 4. Touch the desired color. 4. Select "On" or "Off" and then touch "Save". "On": The rear passengers cannot operate the rear seat entertainment system. Only front - 2012 Toyota Sienna | Navigation Manual - Page 442
screen. Then touch to display page 2 of the D Selecting a keyboard layout Keyboard layout can be changed. 1. Push the "SETUP" button. 2. Touch "General" on the "Setup" screen. Then touch to display page 2 of the "General Settings" screen. "General Settings" screen. 3. Touch "Unit of Measurement - 2012 Toyota Sienna | Navigation Manual - Page 443
SETUP LAYOUT TYPE D Delete personal data The following personal data can be deleted or returned to their data D Voice tag data D Bluetoothr phone data D Phone volume setting D Details phone setting This function is available only when the vehicle is not moving. " "ABC" type " "QWERTY" type 256 - 2012 Toyota Sienna | Navigation Manual - Page 444
Clock settings 1. Push the "SETUP" button. 2. Touch "General" on the "Setup" screen. Then touch to display page 2 of the Used for changing time zones and the on/ off settings of daylight saving time. "General Settings" screen. 1. Push the "SETUP" button. 3. Touch "Delete Personal Data". 2. Touch - 2012 Toyota Sienna | Navigation Manual - Page 445
D Time zone A time zone can be selected and GMT can be set. 1. Push the "SETUP" button. 2. Touch "Clock" on the "Setup" screen. On this screen, the following functions can be performed. No. 1 2 Function Time zone can be changed. (See "D Time zone" on page 258.) "On" or "Off" can be selected for - 2012 Toyota Sienna | Navigation Manual - Page 446
can be set. SCREEN FOR VOICE SETTINGS 1. Push the "SETUP" button. On this screen, the following functions can be guidance during route guidance can be set to "On" or "Off". Voice guidance during audio system use can be set to "On" or "Off". Voice recognition talkback can be set to "On - 2012 Toyota Sienna | Navigation Manual - Page 447
while being guided to your destination. To turn the "Traffic Voice Guidance" on: 1. Push the "SETUP" button. 2. Touch "Voice" on the "Setup" screen. is available only in English. To select English, see "D Selecting a language" on page 253. D When the "Traffic Information" indicator is dimmed, "Auto - 2012 Toyota Sienna | Navigation Manual - Page 448
SETUP Navigation settings Points or areas on the map can be registered. Detailed navigation settings Average page 114.) Deletes previous destinations (See page 119.) Detailed navigation settings (See page 261.) 1. Push the "SETUP" button. 2. Touch "Navi.". 3. Touch "Detailed Navi. Settings". 261 - 2012 Toyota Sienna | Navigation Manual - Page 449
SETUP SCREENS FOR NAVIGATION SETTINGS 4. Touch the items to be set. 5. Touch "Save". On this screen, the following functions can be performed. No. 1 Function Average cruising - 2012 Toyota Sienna | Navigation Manual - Page 450
manually. Miscalculation of the distance caused by tire replacement can also be adjusted. (See "D Current position/ tire change calibration used for the calculation of the estimated travel time and the estimated arrival time can be set. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup - 2012 Toyota Sienna | Navigation Manual - Page 451
possible to display up to 99 hours 59 minutes. D Auto avoid traffic The guidance route automatically changes to another route to avoid heavy congestion. To turn the "Auto Avoid Traffic" on: 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Detailed Navi. Settings" on the - 2012 Toyota Sienna | Navigation Manual - Page 452
button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Detailed Navi. Settings" on the "Navigation Settings" screen. 4. Select "On" of the "Show Free Flowing Traffic". 5. Touch "Save". INFORMATION When the "Traffic Information" indicator is dimmed, "Auto Avoid Traffic", "Traffic Voice Guidance - 2012 Toyota Sienna | Navigation Manual - Page 453
POI category change (Select POI icons) Select from among the 6 icons displayed on the "Customize POI Icons" screen, so that setting of the icons to be displayed on the map screen can be done easily. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup" screen. 3. Touch "Detailed Navi. Settings - 2012 Toyota Sienna | Navigation Manual - Page 454
change calibration The current vehicle position mark can be adjusted manually. Miscalculation of the distance caused by tire replacement can also be adjusted. 1. Push the "SETUP" button. 2. Touch "Navi." on the "Setup vehicle position, see "Limitations of the navigation system" on page 324. 267 - 2012 Toyota Sienna | Navigation Manual - Page 455
SETUP POSITION/DIRECTION CALIBRATION When driving, the current vehicle position mark will be automatically corrected by GPS signals. If GPS reception is poor due to location, you can manually adjust the current vehicle position mark. 4. Touch either the or to ad- just the direction of the - 2012 Toyota Sienna | Navigation Manual - Page 456
SETUP TIRE CHANGE CALIBRATION The tire change calibration function will be used when replacing the tires. This function will adjust the miscalculation caused by the circumference difference between the old and new tires. If this procedure is - 2012 Toyota Sienna | Navigation Manual - Page 457
, the following messages will not be displayed. "Telephone settings" can be changed on the "Phone settings" screen. This message appears when the system is in the POI mode and the map scale is over 0.5 miles (1 km). 1. Push the "SETUP" button. The message appears when the map is switched to the - 2012 Toyota Sienna | Navigation Manual - Page 458
voice volume. 3. Touch "OK". D Ring volume setting 1. Touch "Ring Volume". 2. Change each setting according to the following procedures. 3. When you complete all settings, touch "Save". Automatic volume settings for high speed The system will automatically increase the volume by one step up when - 2012 Toyota Sienna | Navigation Manual - Page 459
- Manage phone D Initializing the settings You can initialize the settings. 1. Touch "Default". "Manage phone" is accessed from the "Connect Phone" screen. 1. Push the "SETUP" button. 2. Touch "Phone". 2. Touch "Yes". 3. Touch "Manage Phone". Please refer to the following pages for each setting - 2012 Toyota Sienna | Navigation Manual - Page 460
to the system. 3. When the connection is completed, this screen is displayed. You do not need to enter the phone in case of using the same one. 2. When this screen is displayed, input the passcode displayed on the screen into the phone. For the operation of the phone, see the manual that comes - 2012 Toyota Sienna | Navigation Manual - Page 461
connected You can also register a new Bluetoothr phone in the following way. 1. Push the "SETUP" button. 2. Touch "Phone". 3. Touch "Manage Phone". When another Bluetoothr device is currently not be reconnected depending on the phone you are using. 4. Touch "Options". 5. Touch "New Phone". 274 - 2012 Toyota Sienna | Navigation Manual - Page 462
SETUP 6. Touch "(empty)" to register your cellular phone to the system. The following operations are the same as registered a Bluetoothr phone yet. Although you can register up to 4 Bluetoothr phones in the system, only one Bluetoothr phone can function at a time. 1. Select the phone to connect. - 2012 Toyota Sienna | Navigation Manual - Page 463
2. The "Connect Bluetooth*" screen is displayed. *: Bluetooth is a registered trademark of Bluetooth SIG, Inc. This screen is displayed, and the Bluetoothr audio will stop temporarily. When another Bluetoothr device is connected 3. When the result message is displayed, you can use the Bluetoothr - 2012 Toyota Sienna | Navigation Manual - Page 464
phone which is displayed on the screen. You can change it into a desired name. If you change a device name, the name registered in your cellular phone is not changed. "Device Address" ...The address peculiar to the system. You cannot change it. If you have registered two Bluetoothr phones with - 2012 Toyota Sienna | Navigation Manual - Page 465
SETUP 3. Select the phone to edit. 5. Use the software keyboard to input the device name. 4. This screen is displayed. If you want to change the device name, touch "Edit". 6. Confirm the device name and touch "OK". 278 - 2012 Toyota Sienna | Navigation Manual - Page 466
SETUP D Deleting a Bluetoothr phone 1. Touch "Options". 3. Select the desired phone or touch "Select All", then touch "Delete". You can select multiple phones and delete them at - 2012 Toyota Sienna | Navigation Manual - Page 467
not read the registered data. "Phonebook" is accessed from the "Phonebook Settings" screen. 1. Push the "SETUP" button. 2. Touch "Phone". You can other voice recognition. (For the operation of voice recognition, see "Speech command system" on page 44.) When you select the command of "Add New Phone", - 2012 Toyota Sienna | Navigation Manual - Page 468
Setting the phonebook "Setting the phonebook" is accessed from the "Contacts" screen. 1. Push the "SETUP" button. 2. Touch "Phone". 3. Touch "Phonebook". You can also display the "Contacts" screen in the following way. 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Contacts". 4. - 2012 Toyota Sienna | Navigation Manual - Page 469
phonebook data transferred until then can be memorized in the system. When you have touched "Replace Contacts": If your cellular phone does not support PBAP or OPP service, you can not use this function. If your phone supports PBAP service, you can transfer the phonebook data without operating your - 2012 Toyota Sienna | Navigation Manual - Page 470
SETUP When another Bluetoothr device is connected 4. In case that you have touched "Add Contacts", this screen reconnect automatically when data transfer finishes. (It will not be reconnected depending the phone you are using.) When this screen is displayed, try the transfer operation again. 283 - 2012 Toyota Sienna | Navigation Manual - Page 471
SETUP D Registering the phonebook data You can register the phonebook data. Up to 3 numbers per person can be registered. 1. Touch "New Contact". 3. Input the phone number and touch "OK". If you want to use the tone signal after the phone number, input the tone signal too. 2. Use the software - 2012 Toyota Sienna | Navigation Manual - Page 472
SETUP D Editing the phonebook data You can register the phone number in "Phone#1", "Phone#2" and "Phone#3" separately. 5. When two or less numbers in total are registered - 2012 Toyota Sienna | Navigation Manual - Page 473
SETUP You can also display the "Edit Contact" screen in the following ways. From "Contact Data" screen 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Contacts". 4. - 2012 Toyota Sienna | Navigation Manual - Page 474
SETUP From "Call History" screen 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Call History". 4. Select the desired number from the list. D Deleting the phonebook data You can delete the data. When you release your car, delete all your data on the system. 1. Touch "Delete Contacts - 2012 Toyota Sienna | Navigation Manual - Page 475
SETUP You can also delete it in the following way. 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Contacts". 4. Select the desired data from the list. 3. Touch "Yes". 5. Touch "Options". 6. Touch "Delete Contact". 288 - 2012 Toyota Sienna | Navigation Manual - Page 476
- Speed dials setting "Speed dials setting" is accessed from the "Speed Dials" screen. 1. Push the "SETUP" button. 2. Touch "Phone". 3. Touch "Phonebook". 7. Touch "Yes". INFORMATION When you delete a Bluetoothr phone, the phonebook data will be deleted at the same time. 4. Touch "Manage - 2012 Toyota Sienna | Navigation Manual - Page 477
SETUP You can also display the "Speed Dials" screen in the following way. 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Speed Dials". D Registering the speed - 2012 Toyota Sienna | Navigation Manual - Page 478
SETUP 3. Touch the desired phone number. 5. If you select a touch−screen button you registered before, this screen is displayed. Touch "Yes" if you want to replace it. 4. Touch the touch−screen button you want to register in. 6. When this screen is displayed, the operation is complete. 291 - 2012 Toyota Sienna | Navigation Manual - Page 479
SETUP You can also register the speed dial in the following ways. From "Speed Dial" screen 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Speed Dials". 6. - 2012 Toyota Sienna | Navigation Manual - Page 480
the desired data from the list. 7. This screen is displayed. The following operations are the same as the operation when you operate it from the "SETUP" button. 5. Touch "Options". 6. Touch "Set Speed Dial". 293 - 2012 Toyota Sienna | Navigation Manual - Page 481
SETUP D Editing the speed dial You can edit the speed dial. 4. Use the software keyboard to input the name. 1. Touch "Edit Speed Dials". 5. Touch "Save". 2. Touch the touch−screen button you want to edit. 3. Touch "Edit". 294 - 2012 Toyota Sienna | Navigation Manual - Page 482
SETUP D Deleting the speed dial You can delete the speed dial. 3. Touch "Yes". 1. Touch "Delete Speed Dials". 2. Select the desired data or touch "Select All", then touch "Delete". You can select multiple data and delete them at the same time. 295 - 2012 Toyota Sienna | Navigation Manual - Page 483
SETUP - Deleting call history You can delete the call history. 1. Touch "Delete Call History". 3. Select the desired data or touch "Select All", then touch "Delete". You can select multiple data and delete them at the same time. 2. Select the desired history to delete. 4. Touch "Yes". 296 - 2012 Toyota Sienna | Navigation Manual - Page 484
" button. 2. Touch "Phone". 3. Touch "Call History". "Setting the voice tag" is done by displaying "Voice Tags" screen. 1. Push the "SETUP" button. 2. Touch "Phone". 3. Touch "Phonebook". 4. Touch "Delete". 4. Touch "Manage Voice Tags". 5. This screen is displayed. The following operations are - 2012 Toyota Sienna | Navigation Manual - Page 485
SETUP You can also display "Voice Tags" screen in the following way. 1. Push the "INFO/PHONE" button. 2. Touch "Phone". 3. Touch "Contacts". D Registering the voice tag You - 2012 Toyota Sienna | Navigation Manual - Page 486
SETUP You can also register the voice tag in the following way. 1. Push the "INFO/ the voice tag registration, touch "OK". INFORMATION When you use the voice tag, do not change the language setting from the language setting used when registering. If they are different, the voice recognition can - 2012 Toyota Sienna | Navigation Manual - Page 487
D Editing the voice tag 7. This screen is displayed. The following operations are the same as the operation when you operate it from the "SETUP" button. 1. Touch "Edit Voice Tags". 2. Select the data you want to edit. 3. This screen is displayed. The following operations are the same as the - 2012 Toyota Sienna | Navigation Manual - Page 488
- Bluetoothr D Deleting the voice tag You can confirm and change the Bluetoothr settings. 1. Push the "SETUP" button. 2. Touch "Phone". 1. Touch "Delete Voice Tags". 3. Touch "Bluetooth*". *: Bluetooth is a registered trademark of Bluetooth SIG, Inc. 2. Select the desired data or touch "Select - 2012 Toyota Sienna | Navigation Manual - Page 489
following procedures. Changing the handsfree power The "Handsfree Power" display shows the following state. When "Handsfree Power" is "On": Vehicles with smart key system- The Bluetoothr phone is automatically connected when you turn the ignition to ACCESSORY or IGNITION ON mode. Vehicles without - 2012 Toyota Sienna | Navigation Manual - Page 490
SETUP 1. Touch "Handsfree Power". 3. Touch "Save". In case that "Handsfree Power" is changed from "Off" into "On", Bluetoothr connection will begin. When you connect the phone while Bluetoothr audio is playing 2. Touch "On" or "Off". This screen is - 2012 Toyota Sienna | Navigation Manual - Page 491
Touch "Edit" of "Device Name". 1. Touch "Edit" of "Passcode". 2. Use the software keyboard to input the device name. 2. Input a passcode and touch "OK". INFORMATION The device names are common Bluetoothr audio and Bluetoothr phone. If you change the device name of the phone, the device name of - 2012 Toyota Sienna | Navigation Manual - Page 492
SETUP D Initializing the Bluetoothr settings You can initialize the settings. If you connect a phone Bluetoothr audio is playing while 1. Touch "Default". This screen is displayed, and the Bluetoothr audio will stop temporarily. 2. Touch "Yes". If "Handsfree Power" is changed from "Off" into " - 2012 Toyota Sienna | Navigation Manual - Page 493
. 1. Push the "SETUP" button. 2. Touch "Phone". D Incoming call display You can select the method of the incoming call display. 3. Touch "Details". 4. Do each setting according to the following procedures. 5. When you complete each setting, touch "Save". 1. Touch Mode". "Incoming Call Display - 2012 Toyota Sienna | Navigation Manual - Page 494
displayed on the upper side of the screen. You can only operate the steering switch. Vehicles with smart key system- When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode and the Bluetoothr is automatically connected, the connection check is displayed. Vehicles without smart key - 2012 Toyota Sienna | Navigation Manual - Page 495
SETUP D Initializing the settings You can initialize the settings. 1. Touch "Display Phone Status". 1. Touch "Default". 2. Touch "On" or "Off". 2. Touch "Yes". 308 - 2012 Toyota Sienna | Navigation Manual - Page 496
when you choose the portable player. 1. Push the "SETUP" button. U10003GS U10025GS 2. Touch "Audio" on "Setup" screen. 4. Select desired portable player and then touch "OK". Although you can register up to two portable players in the system, only one portable player can function at a time. 309 - 2012 Toyota Sienna | Navigation Manual - Page 497
portable player is not changed. U10004GS 1. Touch "Portable Player Info" on "Select Portable Player" screen. U10005GS U10004GS 2. Touch "Edit" for "Device Name" on "Portable Player Information" screen. Select the desired portable player and then touch "Portable Player Info". U10006GS 3. Use the - 2012 Toyota Sienna | Navigation Manual - Page 498
or "From Portable Player" and then touch "Save". U9005TI 2. Touch "Register" of "Bluetooth∗ Audio" on "BT Audio Settings" screen. ∗: Bluetooth is a registered trademark of Bluetooth SIG.Inc. INFORMATION If the connection method is set to "From Portable Player", "Auto Bluetooth∗ Connect" cannot be - 2012 Toyota Sienna | Navigation Manual - Page 499
SETUP When another Bluetoothr device is connected U10010GS 3. When this screen is displayed, enter the passcode displayed on the screen into the portable player. For the operation of the portable player, see the manual need to enter the portable player in case of using the same one. U10012GS When - 2012 Toyota Sienna | Navigation Manual - Page 500
SETUP (a) Removing a Bluetoothr audio U9006TI 1. Touch "Remove" of "Bluetooth∗ Audio" on "BT Audio Settings" screen. U10016GS If the selected portable player is in use, this screen will appear. Touch "Yes". The system will disconnect the portable player and remove it. U10014GS 2. Select the - 2012 Toyota Sienna | Navigation Manual - Page 501
established. The "Auto Bluetooth∗ Connect" cannot be selected if the connection method is set to "From Portable Player". ∗: Bluetooth is a registered trademark of Bluetooth SIG.Inc. Vehicles with smart key system- When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the selected - 2012 Toyota Sienna | Navigation Manual - Page 502
SETUP (c) Changing the passcode The passcode for registering your portable player on the system. You can change this to 4 to 8 digit number of your choice. The default is "0000". (d) Changing the device name You can change a device name. Even if you change a device name, the name registered your - 2012 Toyota Sienna | Navigation Manual - Page 503
can initialize the settings. When the navigation system is turned on, the "Information" screen displays when it is time to replace a part or certain components. (See page 27.) U9010TI 1. Touch "Default" on "BT Audio Settings" screen. 1. Push the "SETUP" button. U9011TI 2. Touch "Yes". 2. Touch - 2012 Toyota Sienna | Navigation Manual - Page 504
. (See " (b) Dealer setting" on page 319.) "Reminder": When this button is touched, the indicator is illuminated. The system is set to give maintenance information with the "Information" screen. (See page 27.) When the vehicle needs to be serviced, the touch screen button color will change to orange - 2012 Toyota Sienna | Navigation Manual - Page 505
engine coolant "Brake oil": Replace brake fluid "Trans. fluid": Replace transmission fluid "Service": Scheduled maintenance "Air filter": Replace air filter "Personal": New information items can be created separately from provided ones. 5. Input the conditions. "Date": The next maintenance date - 2012 Toyota Sienna | Navigation Manual - Page 506
register a dealer in the system. With dealer information registered, route guidance to the dealer is available. 1. Push the "SETUP" button. 2. Touch "Vehicle" on the "Setup" screen. 3. Touch "Maintenance" on the "Vehicle Settings" screen. 6. Touch "Edit" for the item you want to change. "Dealer": To - 2012 Toyota Sienna | Navigation Manual - Page 507
SETUP D To edit "Dealer" or "Contact" D To edit "Location" 1. Touch "Edit" of "Dealer" or "Contact". 1. Touch "Edit" of "Location". 2. Enter the name using the alphanumeric keys. Up to 32 characters can be entered. 3. Touch "OK". The previous screen will be displayed. 2. Touch the 8 - 2012 Toyota Sienna | Navigation Manual - Page 508
SETUP D To edit "Phone #" (telephone number) 1. Touch "Edit" of "Phone #". 2. Enter the number using number keys. 3. Touch "OK". The previous screen will be displayed. 321 - 2012 Toyota Sienna | Navigation Manual - Page 509
SETUP 322 - 2012 Toyota Sienna | Navigation Manual - Page 510
APPENDIX SECTION APPENDIX 9 D Limitations of the navigation system ...324 D Map database information and updates ...326 Changing the map DVD−ROM ...335 323 - 2012 Toyota Sienna | Navigation Manual - Page 511
The installation of window tinting may obstruct the GPS signals. Most window tinting contains some metallic content that will interfere with GPS signal reception of the antenna in the instrument panel. We advise against the use of window tinting on vehicles equipped with navigation systems. 324 - 2012 Toyota Sienna | Navigation Manual - Page 512
change of direction by going forward and backward, or turning on a turntable in the parking lot. D When leaving a covered parking lot or parking garage. D When a roof carrier is installed. D When driving with tire chains installed During auto reroute, the route guidance may not be available for - 2012 Toyota Sienna | Navigation Manual - Page 513
- After replacing a tire, implement the operation described in the "TIRE CHANGE CALIBRATION". (See page 269.) This navigation system uses tire turning data and is designed to work with factory− specified tires for your vehicle. Installing tires that are larger or smaller than the originally equipped - 2012 Toyota Sienna | Navigation Manual - Page 514
for use in the specific system for which it was created. Except to the extent explicitly permitted by mandatory laws, you may not extract or reutilize any portion of the contents of the DATABASE, nor reproduce, copy, duplicate, modify, adapt, translate, disassemble, decompile, or reverse engineer - 2012 Toyota Sienna | Navigation Manual - Page 515
OUT OF THIS AGREEMENT OR YOUR USE OF THE DATABASE, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR COSTS OF COVER, LOSS OF USE OR BUSINESS INTERRUPTION OR THE due to the passage of time, changing circumstances, and due to the nature of the sources used. The DATABASE does not include or reflect - 2012 Toyota Sienna | Navigation Manual - Page 516
law, regulation, or code, including any Sunshine Act, Public Records Act, Freedom of Information Act, or equivalent, which permits public access and/or reproduction or use of the Licensed Products. In the event that such exemption is challenged under any such laws, this Agreement shall be considered - 2012 Toyota Sienna | Navigation Manual - Page 517
. The following trademarks and registrations are owned by the USPS: United States Postal Service, USPS, and ZIP+4. TERMS AND CONDITIONS Personal Use Only. You agree to use this Data together with vehicle navigation system for the solely personal, non−commercial purposes for which you were licensed - 2012 Toyota Sienna | Navigation Manual - Page 518
(a) use this Data with any products, systems, or applications installed or the passage of time, changing circumstances, sources used and the nature of USE THIS INFORMATION, ANY DEFECT IN THE INFORMATION, OR THE BREACH OF THESE TERMS OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED - 2012 Toyota Sienna | Navigation Manual - Page 519
provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. You agree to submit to the , federal government agency, or any federal official refuses to use the legend provided herein, the Contracting Officer, federal government - 2012 Toyota Sienna | Navigation Manual - Page 520
not decompile, disassemble or reverse engineer any portion of this information, and may not transfer or distribute it in any form, for any purpose. Without limiting the foregoing, you may not use this information with any products, systems, or applications installed or otherwise connected to or in - 2012 Toyota Sienna | Navigation Manual - Page 521
. The use of such marks in this product does not imply any sponsorship, approval, or endorsement by such companies of this product. There are two types of areas available for route guidance. In one type of area, primarily around metropolitan centers, detailed route guidance is available for the - 2012 Toyota Sienna | Navigation Manual - Page 522
APPENDIX - Changing the map DVD−ROM 1. Push the "INFO/PHONE" button. 4. Insert a new map DVD−ROM with the label side up. 2. Touch "Map Data". 5. Push the "LOAD· / CLOSE" button to close the display. 3. Touch " DVD". 335 - 2012 Toyota Sienna | Navigation Manual - Page 523
the display while it is moving. It could damage your navigation system. D If a disc cannot be ejected, do not forcibly take . At this time, the audio disc and the map DVD− ROM will be ejected. 2. Touch "Map Data". INFORMATION dealer to find out if there is a more recent update released. 336 - 2012 Toyota Sienna | Navigation Manual - Page 524
APPENDIX D Certification For vehicles sold in Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Category II - 2012 Toyota Sienna | Navigation Manual - Page 525
APPENDIX 338 - 2012 Toyota Sienna | Navigation Manual - Page 526
of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals from the Global Positioning System (GPS) operated by the U.S. Department of Defense. Using these signals and other vehicle sensors, the system indicates your present position and assists - 2012 Toyota Sienna | Navigation Manual - Page 527
Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly. The accuracy of configuration, vehicle condition or other circumstances. For more information on the limitations of the system, refer to pages 324 through 325. 2 - 2012 Toyota Sienna | Navigation Manual - Page 528
become thoroughly familiar with it. Read the entire Navigation System Owner's Manual to make sure you understand the system. Do not allow other people to use this system until they have read and understood the instructions in this manual. For your safety, some functions may become inoperable when - 2012 Toyota Sienna | Navigation Manual - Page 529
, etc.) frequently change. Therefore, before following any instruction from the system, look to see whether the instruction can be done safely and legally. This system cannot warn about such things as the safety of an area, condition of streets, and availability of emergency services. If unsure - 2012 Toyota Sienna | Navigation Manual - Page 530
Quick guide - - Overview buttons and guidance screen No. 1 2 Name North−up or heading−up symbol Scale indicator "MAP/VOICE" button "DEST" button "INFO/PHONE" button "DISP" button Function This symbol indicates a map view with north−up or heading−up. Touching this symbol changes the map - 2012 Toyota Sienna | Navigation Manual - Page 531
this button to display the "Setup" screen. Touch this button to change the screen mode. Displays the distance, the button Foot print map button "SETUP" button Screen configuration button Distance and time to destination XMr NavTraffic mark "GPS" mark (Global Positioning System) 42 42 22, 102, - 2012 Toyota Sienna | Navigation Manual - Page 532
- Registering home 1 Push the "DEST" button. 2 Touch "Go Home". If home has not been registered, you can register it by touching "Go Home". 3 Touch "Yes". 4 There are 4 different methods to search your home. See "Destination search" on page 52. 7 - 2012 Toyota Sienna | Navigation Manual - Page 533
"Enter". The "Edit Home" screen is displayed. 6 Touch "OK". Registration of home is complete. You can also register home by touching the "SETUP" button. (See " (a) Registering home" on page 103.) You can change the name, location, phone number and icon. (See " (b) Editing home" on page 104.) 8 - 2012 Toyota Sienna | Navigation Manual - Page 534
- Registering preset destinations 1 Push the "DEST" button. U0002SNI 2 Touch one of the preset destination buttons. You can set a preset destination to any preset destination button that has not yet been set. 3 Touch "Yes". 4 There are 4 different methods to search preset destinations. See - 2012 Toyota Sienna | Navigation Manual - Page 535
preset destinations by touching the "SETUP" button. (See " (a) Registering preset destinations" on page 106.) You can change the name, location, phone number and icon. (See " (b) Editing preset destinations" on page 107.) The registered points can be used on - 2012 Toyota Sienna | Navigation Manual - Page 536
- Operation flow: guiding the route 1 Push the "DEST" button. 2 There are 10 different methods to search destinations. See "Destination search" on page 52. 3 Touch "Go to ". The navigation system performs a search for the route. 4 Touch "OK", and start driving. Routes other than the one - 2012 Toyota Sienna | Navigation Manual - Page 537
1 Push the "DEST" button. 2 Touch "Go Home". " Go Home" can be used if your home has been registered. (To register "Home", see " (a) Registering home" on page 103.) 3 Touch "Go to ". The navigation system performs a search for the route. 4 Touch "OK", and start driving. Routes other than - 2012 Toyota Sienna | Navigation Manual - Page 538
button. "Address" A house number and the street address can be input by using the input keys...55 2 "Point of Interest" Select one of the many Points of Interest Emergency" One of the four categories of emergency service points that are already stored in the system's database can be selected...66 5 13 - 2012 Toyota Sienna | Navigation Manual - Page 539
...67 9 "Map" A destination can be selected simply by touching the location on the displayed map...70 10 "Coordinates" A destination can be set using latitudes and longitudes as coordinates...71 11 Preset destination touch screen buttons One of 5 preset destination points can be selected by touching - 2012 Toyota Sienna | Navigation Manual - Page 540
" screen, push the "SETUP" button. "General" Settings are available for language selection, operation sounds, automatic screen change, etc...252 1 "Vehicle" Settings are available for vehicle information such as maintenance information...316 5 "Clock" Used for changing settings for time zones - 2012 Toyota Sienna | Navigation Manual - Page 541
Quick reference ("Information" screen) This screen can be used to display the calendar and information on operation of the hands−free phone, etc. To display the "Information" screen, push the "INFO/PHONE" button. 1 "Phone" - 2012 Toyota Sienna | Navigation Manual - Page 542
17