2007 Yamaha Motorsports Grizzly 125 Automatic Owners Manual - Page 84

2007 Yamaha Motorsports Grizzly 125 Automatic Manual

Get 2007 Yamaha Motorsports Grizzly 125 Automatic PDF manuals and user guides View all 2007 Yamaha Motorsports Grizzly 125 Automatic manuals

Page 84 highlights

1 2 3 4 5 6 7 8 9 10 11 and its mating surface, and then wipe off any grime from the spark plug threads. 3. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. Tightening torque: Spark plug: 12.5 Nm (1.3 m·kgf, 9.0 ft·lbf) 2. Start the engine, warm it up for several minutes, and then turn it off. 3. Wait a few minutes until the oil settles before checking. 4. Remove the engine oil filler cap, and then wipe the dipstick off with a clean rag. 1 NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4-1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. 4. Install the spark plug cap. EBU23261 1. Dipstick Engine oil The engine oil level should be checked before each ride. In addition, the oil must be changed at the intervals specified in the periodic maintenance and lubrication chart. To check the engine oil level 1. Place the ATV on a level surface. 8-10 5. Insert the dipstick into the filler hole (without screwing it in), and then remove it again to check the oil level.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
8-10
1
2
3
4
5
6
7
8
9
10
11
and its mating surface, and then wipe off any
grime from the spark plug threads.
3. Install the spark plug with the spark plug
wrench, and then tighten it to the specified
torque.
NOTE:
If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.
4.
Install the spark plug cap.
EBU23261
Engine oil
The engine oil level should be checked before
each ride. In addition, the oil must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.
To check the engine oil level
1.
Place the ATV on a level surface.
2.
Start the engine, warm it up for several min-
utes, and then turn it off.
3.
Wait a few minutes until the oil settles before
checking.
4.
Remove the engine oil filler cap, and then
wipe the dipstick off with a clean rag.
5.
Insert the dipstick into the filler hole (without
screwing it in), and then remove it again to
check the oil level.
Tightening torque:
Spark plug:
12.5 Nm (1.3 m·kgf, 9.0 ft·lbf)
1. Dipstick
1