2012 Yamaha Motorsports Zuma 50F Owners Manual - Page 47

2012 Yamaha Motorsports Zuma 50F Manual

Get 2012 Yamaha Motorsports Zuma 50F PDF manuals and user guides View all 2012 Yamaha Motorsports Zuma 50F manuals

Page 47 highlights

EAU1722A PERIODIC MAINTENANCE AND ADJUSTMENT 3. Wait a few minutes until the oil settles, remove the oil filler cap, wipe the dipstick clean, insert it back into the oil filler hole (without screwing it in), and then remove it again to check the oil level. TIP The engine oil should be between the minimum and maximum level marks. 4. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. 5. Insert the dipstick into the oil filler hole, and then tighten the oil filler cap. To change the engine oil and clean the oil strainer 1. Start the engine, warm it up for several minutes, and then turn it off. 2. Place an oil pan under the engine to collect the used oil. 3. Remove the engine oil fi ller cap and the engine oil drain bolts A and B to drain the oil from the crankcase. NOTICE: When removing the engine oil drain bolt B, the O-ring, compression spring, and oil strainer will fall out. Take care not to lose these parts.[ECAT1021] 1 1 2 ZAUM00** 1. Engine oil drain bolt B 3 4 5 6 7 8 9 1 1. Engine oil drain bolt A 4. Clean the oil strainer with solvent, and then check it for damage and replace it if necessary. 5. Check the O-ring for damage and replace it if necessary. 6. Install the oil strainer, compression spring, O-ring and engine oil drain bolt B. TIP Make sure that the O-ring is properly seated. 6-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
1
2
3
4
5
6
7
8
9
6-11
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
3. Wait a few minutes until the oil
settles, remove the oil fi
ller cap,
wipe the dipstick clean, insert it
back into the oil filler hole (without
screwing it in), and then remove it
again to check the oil level.
TIP
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil fi
ller cap
and the engine oil drain bolts A
and B to drain the oil from the
crankcase.
NOTICE:
When re-
moving the engine oil drain
bolt B, the O-ring, compression
spring, and oil strainer will fall
out. Take care not to lose these
parts.
[ECAT1021]
1
1.
Engine oil drain bolt A
ZAUM00**
1
1.
Engine oil drain bolt B
4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, compres-
sion spring, O-ring and engine oil
drain bolt B.
TIP
Make sure that the O-ring is properly
seated.