3Com 3C16465 User Guide - Page 4
Safety Information, L’information de Sécurité Importante, Wichtige Sicherheitsinformationen
![]() |
UPC - 662705172712
View all 3Com 3C16465 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
SAFETY INFORMATION Please read the following safety information carefully before installing the Baseline 10/100 Switch. WARNING: Installation and removal of the unit must be carried out by qualified personnel only. 3 If installing the Switch unit in a stack with SuperStack II Hub units, the Baseline 10/100 Switch unit must be installed below the narrower Hub units. 3 The unit should never be connected to an A.C. outlet (power supply) without an earth (ground) connection. 3 The unit must be connected to an earthed (grounded) outlet to comply with European safety standards. 3 The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet. 3 The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet. 3 This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions. 3 Only connect an Advanced Redundant Power System (3C16070) or Redundant Power System (3C565047) to the Redundant Power System socket. France and Peru only This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground). Power Cord Set This must be approved for the country where it will be used. U.S.A. and Canada Denmark Switzerland 3 The cord set must be UL-approved and CSA certified. 3 The minimum specifications for the flexible cord are: No. 18 AWG Type SV or SJ 3-conductor 3 The cord set must have a rated current capacity of at least 10A. 3 The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration. 3 The supply plug must comply with Section 107-2-D1, Standard DK2-1a or DK2-5a. 3 The supply plug must comply with SEV/ASE 1011. †Impédance à la terre L'INFORMATION DE SÉCURITÉ IMPORTANTE Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Baseline 10/100 Switch. AVERTISSEMENT: L'installation et la dépose de ce groupe doivent être confiés à un personnel qualifié. 3 Si vous entassez l'unité Switch avec les unités SuperStack II Hub, l'unité Baseline 10/100 Switch doit être installée en dessous des unités Hub plus étroites. 3 L'unité ne devrait pas etre branchee a une prise de courant C.A. (source de courant) sous aucun prétexte sans un branchement mise à la terre (mise à la masse). 3 Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes européennes de sécurité. 3 Le coupleur d'appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d'appareil EN60320/CEI 320. 3 La prise secteur doit se trouver à proximité de l'appareil et son accès doit être facile. Vous ne pouvez mettre l'appareil hors circuit qu'en débranchant son cordon électrique au niveau de cette prise. 3 L'appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme CEI 950. Ces conditions ne sont maintenues que si l'équipement auquel il est raccordé fonctionne dans les mêmes conditions. 3 Branchez uniquement un Advanced Redundant Power System (3C16070) ou un Redundant Power System (3C565047) sur la prise femelle du Redundant Power System. France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d'un transformateur d'isolement à rapport 1:1, avec un point secondaire de connexion portant l'appellation Neutre et avec raccordement direct à la terre (masse). Cordon électrique Il doit être agréé dans le pays d'utilisation. Etats-Unis et Canada: Danemark: Suisse: 3 Le cordon doit avoir reçu l'homologation des UL et un certificat de la CSA. 3 Le cordon souple doit respecter, à titre minimum, les spécifications suivantes: calibre 18 AWG type SV ou 5J à 3 conducteurs 3 Le cordon doit être en mesure d'acheminer un courant nominal d'au moins 10 A. 3 La prise femelle de branchement doit être du type à mise à la terre (mise à la masse) et respecter la configuration NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V). 3 La prise mâle d'alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a. 3 La prise mâle d'alimentation doit respecter la norme SEV/ASE 1011. WICHTIGE SICHERHEITSINFORMATIONEN Bitte unbedingt vor dem Einbauen des Baseline 10/100 Switch 3 Einheit die folgenden Sicherheitsanweisungen durchlesen. WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal erfolgen. 3 3 Wenn die Baseline 10/100 Switch Einheit in einer Stapel mit anderen SuperStack II Hub Einheiten eingebaut werden soll, muß die Baseline 3 10/100 Switch Einheit unter die schmaleren Hub Einheiten eingebaut werden. 3 Das Gerät ist unter keinen umständen an einen Wechselstrom (A.C.) Netzstecker anzuschließen ohne erdungsleitung. 3 Das Gerät muß an eine geerdete Steckdose angeschlossen werden, die 3 die europäischen Sicherheitsnormen erfüllt. 3 Der Anschlußkabelsatz muß mit den Bestimmungen des Landes übereinstimmen, in dem er verwendet werden soll. 4 Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß eine passende Konfiguration für einen Geräteeingang gemäß EN60320/IEC320 haben. Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden. Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen (Sicherheitskleinstspannung) gemäß IEC 950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden. Nur ein Advanced Redundant Power System (3C16070) oder Redundant Power System (3C565047) an den Redundant Power System Anschluß anschließen.
![](/manual_guide/products/3com-3c16465-user-guide-f16bdea/4.png)