AEG L9FSC949R User Manual - Page 38

The Water Softener technology Soft Water'

Get AEG L9FSC949R PDF manuals and user guides View all AEG L9FSC949R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

38 www.aeg.com Problem Possible solution Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum. Make sure that the appliance receives electrical power. This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre. If you need to open the door, please read carefully «Emergency door opening». The appliance makes an unusual noise and vibrates. Make sure the levelling of the appliance is correct. Refer to 'Installation'. Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation'. Add more laundry in the drum. The load may be too small. The programme duration The ProSense function is able to adjust the programme duraincreases or decreases tion according to the type and the laundry load size. Refer to during programme exe- 'The ProSense load detection' in 'Daily Use' chapter. cution. The washing results are Increase the detergent quantity or use a different detergent. not satisfactory. Use special products to remove the stubborn stains before you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load. Make sure that no other type of detergent has been poured Salt the compartment . In this case, refer to 'Eliminating detergent or other additives from salt compartment'. Make sure that no salt has been poured in the compartment . If it happens, run a rinse cycle or run the washing cycle again. Too much foam in the Reduce the quantity of detergent. drum during the washing cycle. Excessive consumption of salt. Check if the water softener has been set to act also during rinse phase. Refer to 'How to set the water hardness level' in 'The Water Softener technology (Soft Water)' chapter.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Problem
Possible solution
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the
drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance.
Contact the Authorised Service Centre. If you need to open
the door, please read carefully «Emergency door opening».
The appliance makes an
unusual noise and vi-
brates.
Make sure the levelling of the appliance is correct. Refer to 'In-
stallation'.
Make sure that the packaging and/or the transit bolts are re-
moved. Refer to 'Installation'.
Add more laundry in the drum. The load may be too small.
The programme duration
increases or decreases
during programme exe-
cution.
The ProSense function is able to adjust the programme dura-
tion according to the type and the laundry load size. Refer to
'The ProSense load detection' in 'Daily Use' chapter.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
Make sure that no other type of detergent has been poured
the compartment
Salt
. In this case, refer to 'Eliminating deter-
gent or other additives from salt compartment'.
Make sure that no salt has been poured in the compartment
. If it happens, run a rinse cycle or run the washing cycle
again.
Too much foam in the
drum during the washing
cycle.
Reduce the quantity of detergent.
Excessive consumption
of salt.
Check if the water softener has been set to act also during
rinse phase. Refer to 'How to set the water hardness level' in
'The Water Softener technology (Soft Water)' chapter.
www.aeg.com
38