ASRock 4CoreDual-VSTA User Manual - Page 35

REF to ACT / REF to REF Trfc

Get ASRock 4CoreDual-VSTA PDF manuals and user guides View all ASRock 4CoreDual-VSTA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Active to CMD (Trcd) Use this option to select Active to CMD (Trcd). Configuration options: [Auto], [2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the timing by dram SPD. REF to ACT / REF to REF (Trfc) Use this option to select REF to ACT / REF to REF (Trfc). Configuration options: [Auto], [8T] to [71T]. The default value is set to [Auto] to set the timing by dram SPD. ACT(0) to ACT (1) (Trrd) Use this option to select ACT(0) to ACT (1) (Trrd). Configuration options: [Auto], [2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the timing by dram SPD. Read to Precharge (Trtp) Use this option to select Read to Precharge (Trtp). Configuration options: [Auto], [2T], [3T]. The default value is set to [Auto] to set the timing by dram SPD. Write to Read CMD (Twtr) Use this option to select Write to Read CMD (Twtr). Configuration options: [Auto], [1T], [2T] for DDRI; [Auto], [2T], [3T] for DDRII. The default value is set to [Auto] to set the timing by dram SPD. Write Recovery Time (Twr) Use this option to select Write Recovery Time (Twr). Configuration options: [Auto], [2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the timing by dram SPD. DRAM Bus Selection The default value is [Auto], which will automatically select the proper access mode for the system. You may select between [Single Channel] and [Dual Channel] if you have properly set the dual channel memory configuration. DRAM Command Rate Use this to select among [2T Command] and [1T Command] for DRAM Command Rate. The default value is [2T Command]. DRAM Voltage Use this to select among [Auto], [High], [Normal] and [Low] for DRAM Voltage. The default value is [Auto]. AGP Voltage Use this to select among [Auto], [Normal] and [High] for AGP Voltage. The default value is [Auto]. Primary Graphics Adapter This allows you to select [PCI], [AGP], or [PCI Express Gfx.] as the primary graphics adapter. The default vaule is [PCI]. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
35
35
35
35
35
Active to CMD (Trcd)
Use this option to select Active to CMD (Trcd). Configuration options: [Auto],
[2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the timing by
dram SPD.
REF to ACT / REF to REF (Trfc)
Use this option to select REF to ACT / REF to REF (Trfc). Configuration
options: [Auto], [8T] to [71T]. The default value is set to [Auto] to set the
timing by dram SPD.
ACT(0) to ACT (1) (Trrd)
Use this option to select ACT(0) to ACT (1) (Trrd). Configuration options:
[Auto], [2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the
timing by dram SPD.
Read to Precharge (Trtp)
Use this option to select Read to Precharge (Trtp). Configuration options:
[Auto], [2T], [3T]. The default value is set to [Auto] to set the timing by dram
SPD.
Write to Read CMD (Twtr)
Use this option to select Write to Read CMD (Twtr). Configuration options:
[Auto], [1T], [2T] for DDRI; [Auto], [2T], [3T] for DDRII. The default value is set
to [Auto] to set the timing by dram SPD.
Write Recovery Time (Twr)
Use this option to select Write Recovery Time (Twr). Configuration options:
[Auto], [2T], [3T], [4T], and [5T]. The default value is set to [Auto] to set the
timing by dram SPD.
DRAM Bus Selection
The default value is [Auto], which will automatically select the proper ac-
cess mode for the system. You may select between [Single Channel] and
[Dual Channel] if you have properly set the dual channel memory
configuration.
DRAM Command Rate
Use this to select among [2T Command] and [1T Command] for DRAM
Command Rate. The default value is [2T Command].
DRAM Voltage
Use this to select among [Auto], [High], [Normal] and [Low] for DRAM Voltage.
The default value is [Auto].
AGP Voltage
Use this to select among [Auto], [Normal] and [High] for AGP Voltage. The
default value is [Auto].
Primary Graphics Adapter
This allows you to select [PCI], [AGP], or [PCI Express Gfx.] as the primary
graphics adapter. The default vaule is [PCI].