ASRock A770CrossFire User Manual - Page 25

Onboard Headers and Connectors

Get ASRock A770CrossFire PDF manuals and user guides View all ASRock A770CrossFire manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! • Floppy Connector (33-pin FLOPPY1) (see p.11 No. 25) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.11 No. 9) PIN1 IDE1 connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1: see p.11, No. 18) (SATAII_2: see p.11, No. 19) SATAII_2 (SATAII_3: see p.11, No. 17) (SATAII_4: see p.11, No. 15) (SATAII_5: see p.11, No. 16) (SATAII_6: see p.11, No. 14) SATAII_1 SATAII_4 SATAII_3 SATAII_6 SATAII_5 These six Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. SATAII_6 connector can be used for internal storage device or be connected to eSATAII connector to support eSATAII device. Please read "eSATAII Interface Introduction" on page 32 for details about eSATAII and eSATAII installation procedures. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
25
25
25
25
25
FLO
PP
Y
1
P
in
1
the red-striped side to Pin1
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.11 No. 25)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.11 No. 9)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These six Serial ATAII (SATAII)
(SATAII_1:
connectors support SATAII
see p.11, No. 18)
or SATA hard disk for internal
(SATAII_2:
storage devices. The current
see p.11, No. 19)
SATAII interface allows up to
(SATAII_3:
3.0 Gb/s data transfer rate.
see p.11, No. 17)
(SATAII_4:
see p.11, No. 15)
(SATAII_5:
see p.11, No. 16)
(SATAII_6:
see p.11, No. 14)
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
I
D
E
1
PIN1
SATAII_6 connector can be used for internal storage device or be
connected to eSATAII connector to support eSATAII device. Please read
“eSATAII Interface Introduction” on page 32 for details about eSATAII
and eSATAII installation procedures.
80-conductor ATA 66/100/133 cable
SATAII_1
SATAII_3
SATAII_5
SATAII_2
SATAII_4
SATAII_6