ASRock N68-VS3 UCC Quick Installation Guide - Page 17

English, 7 Onboard Headers and Connectors - bios update

Get ASRock N68-VS3 UCC PDF manuals and user guides View all ASRock N68-VS3 UCC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. 2.7 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! • Primary IDE connector (Blue) (39-pin IDE1, see p.2 No. 6) connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1 (PORT 0.0): see p.2, No. 12) (SATAII_2 (PORT 0.1): see p.2, No. 9) (SATAII_3 (PORT 1.0): see p.2, No. 11) (SATAII_4 (PORT 1.1): see p.2, No. 10) SATAII_1 SATAII_2 (PORT 0.0) (PORT 0.1) SATAII_3 SATAII_4 (PORT 1.0) (PORT 1.1) These four Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. English 17 ASRock N68-VGS3 UCC / N68-VS3 UCC Motherboard

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
17
17
17
17
17
ASRock
N68-VGS3 UCC / N68-VS3 UCC
Motherboard
connect the blue end
to the motherboard
English
English
English
English
English
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Primary IDE connector (Blue)
(39-pin IDE1, see p.2 No. 6)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These four Serial ATAII (SATAII)
(SATAII_1 (PORT 0.0):
connectors support SATAII
see p.2, No. 12)
or SATA hard disk for internal
(SATAII_2 (PORT 0.1):
storage devices. The current
see p.2, No. 9)
SATAII interface allows up to
(SATAII_3 (PORT 1.0):
3.0 Gb/s data transfer rate.
see p.2, No. 11)
(SATAII_4 (PORT 1.1):
see p.2, No. 10)
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on the motherboard.
SATAII_1
SATAII_2
(PORT 0.0)
(PORT 0.1)
SATAII_3
SATAII_4
(PORT 1.0)
(PORT 1.1)
connect
the black end
to the IDE devices
80-conductor ATA 66/100/133 cable