ASRock N7AD-SLI User Manual - Page 27

Onboard Headers and Connectors

Get ASRock N7AD-SLI PDF manuals and user guides View all ASRock N7AD-SLI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2.10 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.11 No. 23) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.11 No. 16) PIN1 IDE1 connect the blue end connect the black end to the motherboard to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1 (Port 0): see p.11, No. 15) (SATAII_2 (Port 1): see p.11, No. 10) SATAII_2 (Port 1) (SATAII_3 (Port 2): see p.11, No. 13) (SATAII_4 (Port 3): SATAII_1 (Port 0) see p.11, No. 11) (SATAII_5 (Port 4): see p.11, No. 14) (SATAII_6 (Port 5): see p.11, No. 12) SATAII_4 (Port 3) SATAII_3 (Port 2) SATAII_6 (Port 5) SATAII_5 (Port 4) These six Serial ATAII (SATAII) connectors support SATA data cables for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. SATAII_6 (Port 5) connector can be used for internal storage device or be connected to eSATAII connector to support eSATAII device. Please read "eSATAII Interface Introduction" on page 34 for details about eSATAII and eSATAII installation procedures. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
27
27
27
27
27
2.10 Onboard Headers and Connectors
2.10 Onboard Headers and Connectors
2.10 Onboard Headers and Connectors
2.10 Onboard Headers and Connectors
2.10 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.11
No. 23)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.11
No. 16)
Note:
Please refer to the instruction of your IDE device vendor for the details.
F
LOPP
Y
1
P
in
1
the red-striped side to Pin1
Serial ATAII Connectors
These six Serial ATAII (SATAII)
(SATAII_1 (Port 0):
connectors support SATA data
see
p.11, No. 15)
cables for internal storage
(SATAII_2 (Port 1):
devices. The current SATAII
see
p.11, No. 10)
interface allows up to 3.0 Gb/s
(SATAII_3 (Port 2):
data transfer rate.
see
p.11, No. 13)
(SATAII_4 (Port 3):
see
p.11, No. 11)
(SATAII_5 (Port 4):
see
p.11, No. 14)
(SATAII_6 (Port 5):
see
p.11, No. 12)
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100/133 cable
IDE
1
PIN1
SATAII_6 (Port 5) connector can be used for internal storage device
or be connected to eSATAII connector to support eSATAII device.
Please read “eSATAII Interface Introduction” on page 34 for details
about eSATAII and eSATAII installation procedures.
SATAII_2
SATAII_4
SATAII_6
(Port 1)
(Port 3)
(Port 5)
SATAII_1
SATAII_3
SATAII_5
(Port 0)
(Port 2)
(Port 4)