ASRock Wolfdale1333-GLAN R2.0 User Manual - Page 8

Caution

Get ASRock Wolfdale1333-GLAN R2.0 PDF manuals and user guides View all ASRock Wolfdale1333-GLAN R2.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

CAUTION! 1. FSB1333-CPU will operate in overclocking mode. Under this situation, PCIE frequency will also be overclocked to 115MHz. 2. About the setting of "Hyper Threading Technology", please check page 29. 3. This motherboard supports Untied Overclocking Technology. Please read "Untied Overclocking Technology" on page 25 for details. 4. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 16 for proper installation. 5. Please check the table below for the CPU FSB frequency and its corre- sponding memory support frequency. CPU FSB Frequency Memory Support Frequency 1333 DDR2 533*, DDR2 667 1066 DDR2 533, DDR2 667 800 DDR2 400, DDR2 533, DDR2 667 533 DDR2 400, DDR2 533 * When you use a FSB1333-CPU on this motherboard, it will run at DDR2 500 if you adopt a DDR2 533 memory module. 6. Due to the chipset limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® XP, Windows® XP 64-bit, Windows® VistaTM and Windows® VistaTM 64-bit. 7. Although this motherboard offers stepless control, it is not recom- mended to perform over-clocking. Frequencies other than the recom- mended CPU bus frequencies may cause the instability of the system or damage the CPU. 8. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. 9. Before installing SATAII hard disk to SATAII connector, please read the "SATAII Hard Disk Setup Guide" on page 24 to adjust your SATAII hard disk drive to SATAII mode. You can also connect SATA hard disk to SATAII connector directly. 10. Power Management for USB 2.0 works fine under Microsoft® Windows® VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
8
CAUTION!
1.
FSB1333-CPU will operate in overclocking mode. Under this situation,
PCIE frequency will also be overclocked to 115MHz.
2.
About the setting of
“Hyper Threading Technology”, please check page
29.
3.
This motherboard supports Untied Overclocking Technology. Please read
“Untied Overclocking Technology” on page 25 for details.
4.
This motherboard supports Dual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 16 for proper installation.
5.
Please check the table below for the CPU FSB frequency and its corre-
sponding memory support frequency.
CPU FSB Frequency
Memory Support Frequency
1333
DDR2 533*, DDR2 667
1066
DDR2 533, DDR2 667
800
DDR2 400, DDR2 533, DDR2 667
533
DDR2 400, DDR2 533
* When you use a FSB1333-CPU on this motherboard, it will run at
DDR2 500 if you adopt a DDR2 533 memory module.
6.
Due to the chipset limitation, the actual memory size may be less than
4GB for the reservation for system usage under Windows
®
XP, Windows
®
XP 64-bit, Windows
®
Vista
TM
and Windows
®
Vista
TM
64-bit.
7.
Although this motherboard offers stepless control, it is not recom-
mended to perform over-clocking. Frequencies other than the recom-
mended CPU bus frequencies may cause the instability of the system
or damage the CPU.
8.
While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC
system.
9.
Before installing SATAII hard disk to SATAII connector, please read the “SATAII
Hard Disk Setup Guide” on page 24 to adjust your SATAII hard disk drive to
SATAII mode. You can also connect SATA hard disk to SATAII connector
directly.
10.
Power Management for USB 2.0 works fine under Microsoft
®
Windows
®
Vista
TM
64-bit / Vista
TM
/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.