ASRock Z97 Extreme4/3.1 Quick Installation Guide - Page 36

Installation Procedure - drivers

Get ASRock Z97 Extreme4/3.1 PDF manuals and user guides View all ASRock Z97 Extreme4/3.1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installation Procedure he ASRock USB 3.1/A+C provides two external USB 3.1 ports which support transfer rates up to 10 Gbps. Follow the simple steps below to install the ASRock USB 3.1/A+C. Step 1 Power of the PC and unplug the power cord. Detach all other cables from the PC. Step 2 Remove the side panel from the computer case. *Refer to the documentation that comes with your PC for details. Step 3 Locate an available x4, x8 or x16 PCI Express slot on your motherboard and remove its slot bracket. *To maximize the performance of ASRock USB 3.1/A+C, it is highly recommended to insert the card into the PCIE6 (from CPU) if the slot is not occupied by graphics card. If the PCIE6 is occupied, insert the card into PCIE5 (from CPU). Step 4 Align the ASRock USB 3.1/A+C with the PCI Express slot and press down irmly until it is fully seated in the slot. hen secure the card with the slot bracket's holding screw. Step 5 Replace the side panel. Reconnect the power cord and any other cables that were disconnected. *Jumper Setup: Jumper J1 is set to Pin1-2 by default and allows device charging during S3 (Sleep), S4 (Suspend) or S5 (Power Of) power states. To disable device charging during S3/ S4/S5 (Power Of) power states, you need to move the jumper cap placed on Pin1-2 (default) to Pin2-3. *Please install driver for Windows® 7 (32-bit and 64-bit). 34 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
34
English
Installation Procedure
He ASRock USB 3.1/A+C provides two external USB 3.1 ports which support
transfer rates up to 10 Gbps. Follow the simple steps below to install the ASRock
USB 3.1/A+C.
Step 1
Power oµ the PC and unplug the power cord.
Detach all other cables from the PC.
Step 2
Remove the side panel from the computer case.
*Refer to the documentation that comes with your PC for details.
Step 3
Locate an available x4, x8 or x16 PCI Express slot on your motherboard and remove
its slot bracket.
*To maximize the performance of ASRock USB 3.1/A+C, it is highly recommended
to insert the card into the PCIE6 (from CPU) if the slot is not occupied by graphics
card. If the PCIE6 is occupied, insert the card into PCIE5 (from CPU).
Step 4
Align the ASRock USB 3.1/A+C with the PCI Express slot and press down ±rmly
until it is fully seated in the slot. Hen secure the card with the slot bracket’s holding
screw.
Step 5
Replace the side panel. Reconnect the power cord and any other cables that were
disconnected.
*Jumper Setup:
Jumper J1 is set to Pin1-2 by default and allows device charging during S3 (Sleep),
S4 (Suspend) or S5 (Power Oµ) power states. To disable device charging during S3/
S4/S5 (Power Oµ) power states, you need to move the jumper cap placed on Pin1-2
(default) to Pin2-3.
*Please install driver for
Windows® 7 (32-bit and 64-bit).