Acer AL712 User Guide - Page 3

Detaching LCD Monitor from Its Stand - specification

Get Acer AL712 PDF manuals and user guides View all Acer AL712 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Detaching LCD Monitor from Its Stand Unscrew screws n the swivel base support column and pull downo the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997). Connecting the Display Figure 1-4 1. Power off your computer. 2. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port.(For AL712/AL713)(See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. 4. Make sure connection are secure. Figure 1-5 Attention: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-6) 2. Connect the power cord to an AC power source. Connecting the Audio Cable (For AL712/AL716) 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. (See Fig. 1-7) 2. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. Setting Up the LCD Monitor 1. Turn on the LCD monitor's hard power switch, located on the back of the monitor 2. Turn on the LCD Monitor's soft power switch, located on the bezel of the monitor. Figure 1-6 Figure 1-7 Figure 1-8 Power Management System This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. signal. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
Detaching LCD Monitor from Its Stand
Unscrew screws
the swivel base support column and pull
down
the hinge to release.
Figure 1-3
Interface for Arm Applications
Before installing to mounting device, please refer to Fig.1-3.
The rear of this LCD display has four integrated 4 mm, 0.7 pitches
threaded nuts, as well as four 5 mm access holes in the plastic covering
as illustrated in Figure 1-4. These specifications meet the
VESA Flat
Panel Monitor Physical Mounting Interface Standard
(paragraphs
2.1 and 2.1.3, version 1, dated 13 November 1997).
Figure 1-4
Connecting the Display
1.
Power off your computer.
2.
Connect one end of the signal cable to the LCD Monitor’s VGA
port or DVI port.(For AL712/AL713)(See Fig 1-5)
3.
Connect the other end of the signal cable to the VGA port or
DVI port on your PC.
4.
Make sure connection are secure
.
Figure 1-5
Attention:
This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations.
A ferrite-core interface cable is included in the LCD Monitor package.
This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used.
Connecting the AC Power
1.
Connect the power cord to the LCD Monitor.(Se
Fig. 1-6)
e
2.
Connect the power cord to an AC power source.
Figure 1-6
Connecting the Audio Cable
(For AL712/AL716)
1.
Connect the audio cable to the " LINE OUT " jack on your PC's
audio card or to the front panel's “AUDIO OUT” jack of your
CD ROM drive. (See Fig. 1-7)
2.
Connect the other end of the audio cable to the LCD Monitor's "
LINE IN " jack.
Figure 1-7
Setting Up the LCD Monitor
1.
Turn on the LCD monitor’s hard power switch, located on the
back of the monitor
2.
Turn on the LCD Monitor's soft power switch, located on the
bezel of the monitor.
Figure 1-8
Power Management System
This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The VESA DPMS provides
four power saving modes through detecting a horizontal or vertical sync. signal.
When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator
will light yellow.
3