Acer PL6610T User Manual - Page 57

Warning indicators, Other problems, Remote control problems

Get Acer PL6610T PDF manuals and user guides View all Acer PL6610T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

ADDITIONAL INFORMATION Other problems T he projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within ±20° to the IR receiver on the projector. ‡‡ Make sure there are not any obstructions between the remote control and the projector. Move to within 5 m (16.4 ft) of the projector. ‡‡ Make sure batteries are inserted correctly. ‡‡ Replace batteries if they are exhausted. Warning indicators When the warning indicators (see below) light up or flash, the projector will automatically shutdown: ‡‡ "Lamp" LED indicator is lit red and if "Power" indicator flashes red. ‡‡ "Temp" LED indicator is lit red and if "Power" indicator flashes red. This indicates the projector has overheated. Under normal conditions, the project can be switched back on. ‡‡ "Temp" LED indicator flashes red and if "Power" indicator flashes red. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or flash, please contact your nearest service center for assistance. English 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
English
57
ADDITIONAL INFORMATION
Other problems
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Remote control problems
If the remote control does not work
±
Check the operating angle of the remote control is pointed within ±20° to the IR receiver on the
projector.
±
Make sure there are not any obstructions between the remote control and the projector. Move to within
5 m (16.4 ft) of the projector.
±
Make sure batteries are inserted correctly.
±
Replace batteries if they are exhausted.
Warning indicators
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:
±
“Lamp” LED indicator is lit red and if “Power” indicator flashes red.
±
“Temp” LED indicator is lit red and if “Power” indicator flashes red. This indicates the projector has
overheated. Under normal conditions, the project can be switched back on.
±
“Temp” LED indicator flashes red and if “Power” indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
flash, please contact your nearest service center for assistance.