Adaptec 2060500 User Guide - Page 177

Enabling HostRAID Support

Get Adaptec 2060500 PDF manuals and user guides View all Adaptec 2060500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 177 highlights

Migrating From Adaptec Ultra320 SCSI to HostRAID 14 Click Next again. You may be prompted with this warning message: "The software you are about to install does not contain a Microsoft Digital Signature..." Ignore the warning and click Yes to continue. 15 When the driver is copied on the hard disk drive, click Finish. 16 Click Close on the driver Properties window. 17 You will be prompted to restart the computer. Select Yes. The new HostRAID driver will be displayed under SCSI and RAID controllers in the Device Manager. Enabling HostRAID Support After installing the HostRAID driver, you must enable HostRAID support before you can use the RAID features. To enable HostRAID for the boot channel, follow these steps: 1 Press Ctrl+A keys simultaneously when the Adaptec BIOS appears. 2 Select the channel where your boot drive is connected, then press Enter. 3 From the Options menu, select Configure/View SCSI Controller Settings and press Enter. 4 From the Configuration menu, select HostRAID and press Enter. 5 From the HostRAID Pop-up menu, select Enabled. 6 Press Esc, save change, then Exit. E-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
E-3
Migrating From Adaptec Ultra320 SCSI to HostRAID
14
Click
Next
again. You may be prompted with this warning
message:
“The software you are about to install does not contain a Microsoft
Digital Signature...”
Ignore the warning and click
Yes
to continue.
15
When the driver is copied on the hard disk drive, click
Finish
.
16
Click
Close
on the driver Properties window.
17
You will be prompted to restart the computer. Select
Yes
.
The new HostRAID driver will be displayed under SCSI and
RAID controllers in the Device Manager.
Enabling HostRAID Support
After installing the HostRAID driver, you must enable HostRAID
support before you can use the RAID features. To enable
HostRAID for the boot channel, follow these steps:
1
Press
Ctrl+A
keys simultaneously when the Adaptec BIOS
appears.
2
Select the channel where your boot drive is connected, then
press
Enter
.
3
From the Options menu, select
Configure/View SCSI
Controller Settings
and press
Enter
.
4
From the Configuration menu, select
HostRAID
and press
Enter
.
5
From the HostRAID Pop-up menu, select
Enabled
.
6
Press
Esc
, save change, then Exit.