Alpine CDA-9855 Owners Manual - Page 33

SAT Radio Receiver (Optional) SOURCE/ POWER -/J MUTE 8 • When using the optional remote control (RUE-4190), an SAT Radio Channel can be directly called up with the numeric keypad of the remote control. 1 While in XM or SIRIUS Radio mode, enter the Channel number you want to call up with the numeric keypad on the remote control. 2 Press ENTER on the remote control within 5 seconds to receive the Channel. If the channel number is 3 digits, the Channel is automatically received after the channel number is input. g FUNC. MENU f 9 GlideTouch bar SAT Receiver: XM or SIRIUS Receiver When an optional XM or SIRIUS Receiver Box is connected via the Ai-NET bus, the following operations may be performed. However, the XM Receiver and SIRIUS Receiver cannot be connected at the same time. Receiving Channels with the SAT Radio Receiver (Optional) About SAT Radio Satellite Radio* is the next generation of audio entertainment, with over 100 digital audio channels. For a small monthly fee, subscribers can hear crystal-clear music, sports, news and talk, coast-to-coast via satellite. For more information, visit XM's website at www.xmradio.com., or SIRIUS' website at www.sirius.com. To receive SAT Radio, the separately sold XMDirect™ or SIRIUS Satellite Radio Tuner and an appropriate Ai-NET Interface Adapter will be required. For details, consult you nearest ALPINE dealer. * XM and its corresponding logos are trademarks of XM Satellite Radio Inc. * SIRIUS and its corresponding logos are trademarks of SIRIUS Satellite Radio Inc. • The SAT Receiver controls on the CDA-9855/CDA-9853 are operative only when a SAT Receiver is connected. 1 Press SOURCE/POWER to select XM mode. 2 Press BAND to select XM1, XM2 or XM3. Each press changes the band: XM mode: XM1 → XM2 → XM3 → XM1 SIRIUS mode: SIRIUS1(SR1) → SIRIUS2(SR2) → SIRIUS3(SR3) → SIRIUS1(SR1) 3 Press 8 or 9 to select desired category. 4 Press g or f to select the desired channel. Holding down g or f will change channels continuously. Checking the SAT Radio ID Number A unique Radio ID number is required to subscribe to SAT Radio programming. Each third party XM or SIRIUS radio comes with this number. This number is an 8 character (for XM Radio) or 12 character (for SIRIUS Radio) alphanumeric number. It is printed on a label found on the SAT Receiver. It can also be displayed on the screen of the CDA-9855/CDA-9853 in the following way. 1 While receiving band, press g or f to select channel "0." The unit alternately displays "RADIO ID" for 2 seconds, then the ID number for 10 seconds. 2 To cancel the ID number display, set the channel to other than "0." • You cannot use "O," "S,"" I," or "F" for the ID Number (XM radio Receiver only). • You can check the ID number printed on a label on your third party, SAT Radio Receiver package. Storing Channel Presets 1 Press BAND to select the desired band you want to store. 2 After tuning in the desired channel, press FUNC. to activate the preset mode. 3 Select any one of the preset numbers (1 through 6) by sliding your finger on the GlideTouch bar to the left or right. Press and hold the GlideTouch bar for at least 2 seconds, under the desired preset to store the channel. 4 Repeat the procedure to store up to 5 other channels onto the same band. • To use this procedure for other bands, simply select the band desired and repeat the procedure. • A total of 18 channels can be stored in the preset memory (6 channels for each band; XM1, XM2 and XM3 or SIRIUS1, SIRIUS2 and SIRIUS3). • If you store a channel in a preset memory which already has a station, the current channel will be cleared and replaced with the new one. 31-EN