American Standard 3120.019.021 Installation Instructions
American Standard 3120.019.021 - 3120.019.021 Yorkville Pressure-Assisted Elongated Toilet Bowl Manual
 |
UPC - 033056306833
View all American Standard 3120.019.021 manuals
Add to My Manuals
Save this manual to your list of manuals |
American Standard 3120.019.021 manual content summary:
- American Standard 3120.019.021 | Installation Instructions - Page 1
-ASSISTED TOILETS - Model 2876.016 Yorkville Elongated 15" - Model 2878.016 Yorkville Elongated 16-1/2" High Bowl Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully - American Standard 3120.019.021 | Installation Instructions - Page 2
retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! 6-2 BOLT CAP BOLT CAP CLOSET BOLT CLOSET FLANGE WASHER NUT INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until - American Standard 3120.019.021 | Installation Instructions - Page 3
. NOTE: "XXX" represents color or trim finish options. Specify when ordering. TOILET CADET YORKVILLE PART NO. 7381047-200 7381049-200 4142-016.XXX 4142.801.XXX 735133-400.XXX 3481.016.XXX 3483.016.XXX 3701.016.XXX 3703.016.XXX 034783-XXX0A 034602-0070A 7381054-100 7381053-100 7381052-100 7301320 - American Standard 3120.019.021 | Installation Instructions - Page 4
Step 4 through 7 of installation procedure. Toilet does not shut off a. Supply pressure too low. a. Normal supply pressure must be at least 25 psi. AS AMERICA, INC. ONE YEAR LIMITED WARRANTY If inspection of this AS America, Inc. ("American Standard") plumbing product, within one year after its
-
1 -
2 -
3 -
4
 |
 |
CAUTION:
PRODUCT IS FRAGILE.
TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE:
For proper operation the recommended working pressure is between 25 psi at valve when flushing and 80 psi static.
!
INSTALLATION INSTRUCTIONS
CADET 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2462.016 Cadet Elongated 15"
- Model 2467.016 Cadet Elongated 16-1/2" High Bowl
YORKVILLE 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2876.016 Yorkville Elongated 15"
- Model 2878.016 Yorkville Elongated 16-1/2" High Bowl
Thank you
for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
Closet Flange Set (Cadet Toilets)
Neoprene or Graphite Felt Gasket (Yorkville Toilets)
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely.
Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line.
NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
S
A
V
E
F
O
R
F
U
T
U
R
E
U
S
E
7301312-100
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2009
2-2
3-2
2-1
3-1
DIMENSIONS (Nominal)
NOTE:
Distance from floor to closet
flange centerline (rough-in) must be 4" (102 mm) with flange
surface flush to 1/16" (16mm) max. beyond finished wall.
DIMENSIONS (Nominal)
NOTE:
Distance from wall to closet
flange centerline (rough-in) must be 12" (305 mm)
FOR CADET TOILETS:
FOR YORKVILLE TOILETS:
FLUSH TO
1/16" (16mm)
EXPOSED
CLOSET
FLANGE
CLOSET
BOLTS
168mm
(6-5/8")
PILOT
HOLES
102mm
(4)
346mm
(13-5/8)
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm) apart
and parallel to floor. (Use
putty to hold bolts in place if
necessary.) Brace under
flooring as needed and
drill two mounting pilot
holes as shown.
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm)
apart and parallel to wall.
INSTALL CLOSET BOLTS
305mm
(12)
CLOSET FLANGE
CLOSET BOLTS
29-3/4"
(752mm)
18-1/2"
(470mm)
20-1/2"
(516mm)
9"
(230mm)
14"
(356mm)
15"
(381mm)
HIGH BOWL
16-1/2"
(419mm)
29-1/4"
(743mm)
HIGH BOWL
30-3/4"
(780mm)
13-5/8"
(346mm)
12"
(305mm)
9"
(226mm)
1/2"
(11mm)
30-1/4"
(768mm)
20-1/2"
(516mm)
18-1/2"
(470mm)
12"
(305mm)
13-3/4"
(347mm)
9-1/2"
(238mm)
14"
(356mm)
6"
(150mm)
9"
(226mm)
1"
(27mm)
15"
(381mm)
HIGH BOWL
16-1/2"
(419mm)
29-1/4"
(742mm)
HIGH BOWL
30-3/4"
(781mm)