American Standard Cadet-3 Installation Instructions - Page 4
Repair Parts List - reviews
UPC - 033056671351
View all American Standard Cadet-3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank. NOTE: "XXX" represents color or trim finish options. Specify when ordering. TANK NUMBER 4007.516 4007.500 4007.016 4007.100 4007.428 4007.101 4007.151 4007.458 4007.128 PART NO. 738938-XXX0A 034783-XXX0A 7381125-400.0070A 7381146-401.0070A 7381193-201.0070A 7301021-0070A 738570-100.0070A 735127-400.XXX 735124-400.XXX 7381146-405.0070A 7381146-406.0070A 7381146-402.0070A 7381148-200.0070A 7381162-200.0070A 7381193-203.0070A DESCRIPTION TRIP LEVER - STANDARD LEFT HAND BOLT CAP KIT FLUIDMASTER 400A VALVE FLUSHVALVE ASSEMBLY 3 INCH (INCLUDES FLAPPER) FLAPPER ASSEMBLY 3 INCH TANK COUPLING KIT #253 REFILL TUBE TANK COVER TANK COVER FLUSHVALVE ASSEMBLY HET - 3 INCH (INCLUDES FLAPPER) FLUSHVALVE ASSEMBLY HET - 3 INCH (INCLUDES FLAPPER) FLUSHVALVE ASSEMBLY 3 INCH (INCLUDES FLAPPER) EZ INSTALL BOLT CAP KIT EZ INSTALL TANK COUPLING KIT FLAPPER ASSEMBLY 3 INCH ✔✔ ✔ ✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔ ✔ ✔ ✔ PROBLEM Does not flush TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION a. Water supply valve closed. b. Supply line blocked. a. Open valve and allow water to fill tank. b. Shut off water supply, disconnect supply line and inspect all gaskets and washers. Reassemble. Also, see Fluidmaster maintenance. (see Step 13) Poor or sluggish flush c. Flush valve chain too loose or disconnected. d. Sand or debris lodged in water control. a. Bowl water level too low. Toilet leaks Toilet does not shut off b. Supply valve partly closed. c. Partially clogged trapway and/or drain pipe and/or vent. d. Supply pressure too low. a. Poor supply line connection. b. Poor bowl to tank/floor connection. a. Flush valve chain too tight, holding flush valve open. b. Flush valve seat and/or flapper worn or deformed. c. Sand or debris lodged in water control. c. Readjust chain length as required. d. Shut off water supply. Remove cap and clean as per Step 13. a. Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged. b. Open supply valve fully. Be sure that proper supply tube size is used. c. Remove obstruction. Consult a plumber if necessary. d. Normal supply pressure must be at least 20 psi. a. Review Step 9 of installation procedure. b. Review Step 4 through 7 of installation procedure. a. Readjust chain length as needed. Review Step 10. b. Shut off water supply. Replace flush valve. c. Shut off water supply. Remove cap and clean per Step 13. In the United States: American Standard Brands P.O. Box 6820 Piscataway, New Jersey 08855 Attention: Director of Consumer Affairs For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 442-1902 www.americanstandard-us.com In Canada: AS Canada ULC 5900 Avebury Rd. Mississauga, Ontario Canada L5R 3M3 Toll Free: (800) 387-0369 www.americanstandard.ca - 4 - In Mexico: Customer Service Manager AS Maquila, S.A. de C.V. Via Morelos #330 Col. Santa Clara Ecatepec 55540 Edo. Mexico www.americanstandard.com.mx 7 3 0110 2 - 10 0 Rev. K