Asko WL6511XXL User manual WL6511XXL Use & Care Guide EN (English UCG 2+1 - Page 25

Level adjustment, Connecting water supply hoses

Page 25 highlights

Installation instructions Level adjustment 1. The washer must be installed on a sturdy and solid floor or the unit may make considerable noise, vibrate and cause a malfunction. 2. Adjust the level of washer using adjustable legs. • Please check if there is any gap between the four adjustable legs and the floor. • Turn the adjustable legs with the enclosed wrench to adjust the level of washer and make it sure that the machine does not move when you push on it. • After the adjustment are finished, turn the locking nuts up tightly so that the washer maintains the adjustment. 3. Make sure that the washer does not move when you press down on the four corners of the machine. • Check for leakage of washing machine connections by turning the tap completely on. • Periodically check the condition of the hose and replace the hose if necessary. • Make sure that there is no kink in the hose and that it is not crushed. • Make sure to connect the hot water valve on the machine to the hot water valve on the wall and that cold is connected to cold. The hot water hose has a red stripe, the cold has a blue stripe. Note! There should be no rocking of the washer and all of the adjustable legs should be sitting firmly on the floor. Connecting water supply hoses • Water supply pressure must be between 4.5 and 145 PSI(30~1000 kPa). • Do not cross-thread when connecting inlet hoses to the inlet valves. If the water supply pressure is more than 145 PSI, a pressure reducing device should be installed. • Two Sealing washers are supplied with the water inlet hoses to prevent water leaks. Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact our Customer Care Center. Do not install your washing machine in a room where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below the freezing point. If the appliance is delivered in the winter months and temperatures are below freezing, store the washing machine at room temperature for a few hours before putting it into operation. Customer Care Center 25 1-800-898-1879 www.askousa.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31

25
Customer Care Center
1-800-898-1879
www.askousa.com
Installation instructions
Level adjustment
The washer must be installed on a
1.
sturdy and solid floor or the unit may
make considerable noise, vibrate and
cause a malfunction.
Adjust the level of washer using
2.
adjustable legs.
Please check if there is any gap
between the four adjustable legs and
the floor.
Turn the adjustable legs with the
enclosed wrench to adjust the level
of washer and make it sure that the
machine does not move when you
push on it.
After the adjustment are finished, turn
the locking nuts up tightly so that the
washer maintains the adjustment.
Make sure that the washer does not
3.
move when you press down on the four
corners of the machine.
Note!
There should be no rocking of the washer
and all of the adjustable legs should be
sitting firmly on the floor.
Connecting water supply hoses
Water supply pressure must be between
4.5 and 145 PSI(30~1000 kPa).
Do not cross-thread when connecting
inlet hoses to the inlet valves. If the
water supply pressure is more than 145
PSI, a pressure reducing device should
be installed.
Two Sealing washers are supplied with
the water inlet hoses to prevent water
leaks.
Check for leakage of washing machine
connections by turning the tap
completely on.
Periodically check the condition of the
hose and replace the hose if necessary.
Make sure that there is no kink in the
hose and that it is not crushed.
Make sure to connect the hot water
valve on the machine to the hot water
valve on the wall and that cold is
connected to cold. The hot water hose
has a red stripe, the cold has a blue
stripe.
Repairs to the washing machine must
only be carried out by qualified personnel.
Repairs carried out by inexperienced
persons may cause injury or serious
malfunctioning. Contact our Customer Care
Center.
Do not install your washing machine in a
room where temperatures below freezing
may occur.
Frozen hoses may burst under pressure.
The reliability of the electronic control unit
may be impaired at temperatures below the
freezing point. If the appliance is delivered
in the winter months and temperatures are
below freezing, store the washing machine
at room temperature for a few hours before
putting it into operation.