Asus AT5NM10T-I NA User Manual - Page 21

Serial ATA connectors 7-pin SATA_1, SATA_2, SATA_E1, SATA_E2, USB connector 10-1 pin USB78

Get Asus AT5NM10T-I NA PDF manuals and user guides View all Asus AT5NM10T-I NA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND GND RSATA_TXPE2 RSATA_TXNE2 GND RSATA_RXPE2 RSATA_RXNE2 GND GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND GND RSATA_RXNE1 RSATA_RXPE1 GND RSATA_TXNE1 RSATA_TXPE1 GND AT5NM10T-I 2. Serial ATA connectors (7-pin SATA_1, SATA_2, SATA_E1, SATA_E2) These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via Serial ATA 3.0 Gb/s signal cables. SATA3G_E2 SATA3G_2 SATA3G_E1 SATA3G_1 AT5NM10T-I SATA 3.0Gb/s connectors • Install the Windows® XP Service Pack 3 or later version before using Serial ATA. • The SATA3G_E1/E2 (black) connectors are for data drives only. ATAPI device is not supported. 3. USB connector (10-1 pin USB78) This connector is for a USB 2.0 port. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. This USB connector complys with USB 2.0 specification that supports up to 480 Mbps connection speed. USB78 PIN 1 AT5NM10T-I USB2.0 connector Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard! The USB module cable is purchased separately. USB+5V USB_P8USB_P8+ GND NC AT5NM10T-I USB+5V USB_P7USB_P7+ GND 1-11 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
1-11
Chapter 1: Product introduction
2.
Serial ATA connectors (7-pin SATA_1, SATA_2, SATA_E1, SATA_E2)
These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via
Serial ATA 3.0 Gb/s signal cables.
• Install the Windows
®
XP Service Pack 3 or later version before using Serial ATA.
•
The SATA3G_E1/E2 (black) connectors are for data drives only. ATAPI device is not
supported.
3.
USB connector (10-1 pin USB78)
This connector is for a USB 2.0 port. Connect the USB module cable to this connector,
then install the module to a slot opening at the back of the system chassis. This USB
connector complys with USB 2.0 specification that supports up to 480 Mbps connection
speed.
Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard!
The USB module cable is purchased separately.
GND
RSATA_RXNE1
RSATA_RXPE1
GND
RSATA_TXNE1
RSATA_TXPE1
GND
SATA3G_E2
SATA3G_E1
GND
RSATA_TXPE2
RSATA_TXNE2
GND
RSATA_RXPE2
RSATA_RXNE2
GND
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA3G_2
SATA3G_1
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
AT5NM10T-I
AT5NM10T-I SATA 3.0Gb/s connectors
AT5NM10T-I
AT5NM10T-I USB2.0 connector
PIN 1
USB+5V
USB_P8-
USB_P8+
GND
NC
USB+5V
USB_P7-
USB_P7+
GND
USB78