Asus CUBX-E CUBX-E User Manual - Page 33

Pin Third / Fourth Ide

Get Asus CUBX-E PDF manuals and user guides View all Asus CUBX-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

3. HARDWARE SETUP 8) IDE Connectors (40-1 pin PRIMARY / SECONDARY IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to your hard disk documentation for the jumper settings. (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). TIP: You may configure two hard disks to be both Masters with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector and select the boot disk through the BIOS. NOTE: Orient the red stripe to PIN 1. ® Secondary IDE Connector Primary IDE Connector 3. H/W SETUP Connectors CUBX-L IDE Connectors PIN 1 (40-1 pin THIRD / FOURTH IDE) (only on CUBX-E) Connect the 40-pin 80-conductor cable's blue connector to the motherboard's primary (recommended) or secondary IDE connector, and then connect the corresponding gray connector to your UltraDMA/100 / UltraDMA/66 slave device (hard disk drive) and the black connector to your UltraDMA/100 / UltraDMA/ 66 master device. It is recommended that non-UltraDMA/100 / Ultra/66 devices be connected to the secondary IDE connector. NOTE: Orient the red stripe to PIN 1. ® Fourth IDE Connector Third IDE Connector Secondary IDE Connector Primary IDE Connector CUBX-E IDE Connectors PIN 1 PIN 1 NOTES: UltraDMA/100 is backward compatible with DMA/66, DMA/33, and DMA and with existing DMA devices and systems so there is no need to upgrade current EIDE/IDE drives and host systems. If you have more than two UltraDMA/100 / UltraDMA/66 devices, you will need to purchase another UltraDMA/100 / UltraDMA/66 cable. The hole near the blue connector on the UltraDMA/100 / UltraDMA/66 cable is intentional. IMPORTANT: UltraDMA/66 and UltraDMA/100 IDE devices require a 40-pin 80-conductor cable to be enabled. ASUS CUBX-L/CUBX-E User's Manual 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
ASUS CUBX-L/CUBX-E User’s Manual
33
3. HARDWARE SETUP
Connectors
3. H/W SETUP
8)
IDE Connectors
(40-1 pin PRIMARY / SECONDARY IDE)
These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s). If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly. Please refer to
your hard disk documentation for the jumper settings.
(Pin 20 is removed to
prevent inserting in the wrong orientation when using ribbon cables with
pin 20 plugged).
TIP:
You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector and select the boot disk through the BIOS.
CUBX-L IDE Connectors
Primary IDE Connector
PIN 1
Secondary IDE Connector
NOTE:
Orient the red stripe to PIN 1.
(40-1 pin THIRD / FOURTH IDE) (
only on CUBX-E
)
Connect the 40-pin 80-conductor cable’s blue connector to the motherboard’s
primary (recommended) or secondary IDE connector, and then connect the cor-
responding gray connector to your UltraDMA/100 / UltraDMA/66 slave device
(hard disk drive) and the black connector to your UltraDMA/100 / UltraDMA/
66 master device. It is recommended that non-UltraDMA/100 / Ultra/66 devices
be connected to the secondary IDE connector.
CUBX-E IDE Connectors
NOTE:
Orient the red stripe to PIN 1.
Primary IDE Connector
PIN 1
Secondary IDE Connector
Third IDE Connector
PIN 1
Fourth IDE Connector
NOTES:
UltraDMA/100 is backward compatible with DMA/66, DMA/33, and
DMA and with existing DMA devices and systems so there is no need to upgrade
current EIDE/IDE drives and host systems.
If you have more than two UltraDMA/100 / UltraDMA/66 devices, you will
need to purchase another UltraDMA/100 / UltraDMA/66 cable.
The hole near the blue connector on the UltraDMA/100 / UltraDMA/66 cable is
intentional.
IMPORTANT:
UltraDMA/66 and UltraDMA/100 IDE devices require a 40-pin
80-conductor cable to be enabled.