Asus Maximus Formula Maximus Formula user's manual English Edition Version E33 - Page 66

For watercooling system with 1/2 or 10mm ID tubes

Get Asus Maximus Formula - Republic of Gamers Motherboard PDF manuals and user guides
UPC - 610839156382
View all Asus Maximus Formula manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

For watercooling system with 1/2" or 10mm ID tubes 1. Insert a fitting (1/2" to 3/8" ID or 10mm to 3/8" ID) into the tube. Your watercooling system may come with tube clips. Use the clips to fasten the fittings and the tubes together. 2. Connect a supplied 3/8" ID tube to the fitting. 3. Firmly press a tube clip and hitch it to the bottom end of the 3/8" ID tube. 4. Press another clip and hitch it to the top end of the 3/8" ID tube. 1 2 3 4 5. Press the clip and connect the assembled tube to the waterblock. When done, release the clip to tighten the two together. 6. Repeat Step 1 to 5 for another tube. Make sure that both tubes are well connected to prevent leak, and then fill the coolant into the reservoir. The picture shows a watercooling system installed to the motherboard. 5 6 2-40 Chapter 2: Hardware information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
2-40
Chapter 2: Hardware information
5
6
5.
Press the clip and connect the assembled tube to the waterblock. When
done, release the clip to tighten the two together.
6.
Repeat Step 1 to 5 for another tube. Make sure that both tubes are well
connected to prevent leak, and then fill the coolant into the reservoir. The
picture shows a watercooling system installed to the motherboard.
3
2
1
4
For watercooling system with 1/2” or 10mm ID tubes
1.
Insert a fitting (1/2” to 3/8” ID or 10mm to 3/8” ID) into the tube.
Your watercooling system may come with tube clips. Use the clips to fasten the
fittings and the tubes together.
2.
Connect a supplied 3/8” ID tube to the fitting.
3.
Firmly press a tube clip and hitch it to the bottom end of the 3/8” ID tube.
4.
Press another clip and hitch it to the top end of the 3/8” ID tube.