Asus P2-PE2 Pundit-PE2 User''s Manual for English Edition - Page 44

Connectors

Get Asus P2-PE2 PDF manuals and user guides View all Asus P2-PE2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

4.3 Connectors 4.3.1 Rear panel connectors Refer to section "1.3 Rear panel" for a description of the rear panel I/O ports. 4.3.2 Internal connectors 1 . Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 133/100/66 signal cable. The Ultra DMA 133/100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. IDE connector PRI_IDE PIN 1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. 4-4 Chapter 4: Motherboard info

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
4-4
4-4
4-4
4-4
4-4
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
4.3
Connectors
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Refer to section
“
1.3 Rear panel
”
for a description of the rear panel I/O ports.
4.3.2
4.3.2
4.3.2
4.3.2
4.3.2
Internal connectors
Internal connectors
Internal connectors
Internal connectors
Internal connectors
1.
1.
1.
1.
1.
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
This connector is for an Ultra DMA 133/100/66 signal cable. The Ultra
DMA 133/100/66 signal cable has three connectors: a blue connector
for the primary IDE connector on the motherboard, a black connector
for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk
drive), and a gray connector for an Ultra DMA 133/100/66 IDE master
device (hard disk drive). If you install two hard disk drives, you must
configure the second drive as a slave device by setting its jumper
accordingly. Refer to the hard disk documentation for the jumper
settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE
devices.
IDE connector
PIN 1
PRI_IDE
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.