Asus P3-PH4C User Manual - Page 31

Installing hard disk drives HDDs

Get Asus P3-PH4C PDF manuals and user guides View all Asus P3-PH4C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

2.8 Installing hard disk drives (HDDs) The system comes with two 3.5-inch drive bays (labeled 1 and 2) for installation of two Serial ATA hard disk drives or one IDE HDD (if you have installed an optical drive). 2.8.1 Hard disk drive bays The drive bays incorporate a screw‑less design that allows you to install and remove a hard disk drive without driving screws on the chassis. Each drive bay has a HDD screw lock and four screws rails (two on each side of the bay) that trap the HDD screws and secure the drive in the place. HDD screw lock Screw rails 21 Screw rails When installing one hard disk drive, install it on the upper HDD bay. 2.8.2 SATA hard disk drive installation To install a SATA hard disk drive: 1. Insert the rubber washers to the HDD screws. Refer to the illustration on the right. Rubber washer mat 1 2. Drive four screws (two on each side of the drive) on the drive screw holes. Rubber washer 2 2 ASUS Pundit P3-PH4C 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
2-15
ASUS Pundit P3-PH4C
2.8
Installing hard disk drives (HDDs)
The system comes with two 3.5-inch drive bays (labeled 1 and 2) for
installation of two Serial ATA hard disk drives or one IDE HDD (if you have
installed an optical drive).
2.8.2
SATA hard disk drive installation
To install a SATA hard disk drive:
When installing one hard disk drive, install it on the upper HDD bay.
1.
Insert the rubber washers to
the HDD screws. Refer to the
illustration on the right.
2.
Drive four screws (two on
each side of the drive) on the
drive screw holes.
Rubber washer
Rubber washer mat
1
2
2
HDD screw lock
Screw rails
1
2
Screw rails
2.8.1 Hard disk drive bays
The drive bays incorporate a
screw-less design that allows you
to install and remove a hard disk
drive without driving screws on the
chassis. Each drive bay has a HDD
screw lock and four screws rails (two
on each side of the bay) that trap
the HDD screws and secure the drive
in the place.