Asus P5PEVM Motherboard Installation Guide - Page 37

connectors 40-1 pin PRI_IDE, SEC_IDE

Get Asus P5PEVM PDF manuals and user guides View all Asus P5PEVM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) These connectors are for Ultra DMA 100/66/33 signal cables. There are three interfaces on each Ultra DMA 100/66/33 signal cables: blue, black, and gray. Connect the blue interface into the motherboad's IDE connector, then select the following modes to configure your hard disk drive(s). Single device Two devices Drive Jumper Setting Mode of Devices Cable Connector Cable-select or Master - Cable-select Master Slave Master Master Slave Slave Black Black Gray Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66/33 IDE devices. If any device jumper is set to "Cable-select", make sure all other device jumpers have the same setting. PRI_IDE P5PE-VM SEC_IDE R P5PE-VM IDE Connectors ASUS P5PE-VM 1-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
ASUS P5PE-VM
1-25
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA
100/66/33
IDE
devices.
2.
IDE
connectors (40-1 pin PRI_IDE, SEC_IDE)
These connectors are for Ultra DMA 100/66/33 signal cables.
There are three interfaces on each Ultra DMA 100/66/33 signal
cables: blue, black, and gray. Connect the blue interface into the
motherboad’s IDE connector, then select the following modes to
configure your hard disk drive(s).
Single device
Cable-select or Master
-
Black
Two devices
Cable-select
Master
Black
Slave
Gray
Master
Master
Black or gray
Slave
Slave
Drive Jumper Setting
Mode of Devices
Cable Connector
If any device jumper is set to “Cable-select”, make sure all other device
jumpers have the same setting.
P5PE-VM
P5PE-VM IDE Connectors
SEC_IDE
PRI_IDE