Asus P7P55D-E LX User Manual - Page 38

Digital audio connector 4-1 pin SPDIF_OUT, Marvell, Serial ATA 6.0 Gb/s connectors 7-pin SATA_6G_1/2

Get Asus P7P55D-E LX PDF manuals and user guides View all Asus P7P55D-E LX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

8. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. The S/PDIF module is purchased separately. 9. Marvell® Serial ATA 6.0 Gb/s connectors (7-pin SATA_6G_1/2 [gray]) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. • These connectors are set to Standard IDE mode by default. In Standard IDE mode, you can connect Serial ATA boot/data hard disk drives to these connectors. • You must install Windows® XP Service Pack 2 or later versions before using Serial ATA hard disk drives. • When using hot-plug and NCQ, set the Marvell 9123 Controller item in the BIOS to [AHCI Mode]. Refer to section Onboard Devices Configuration for details. 1-26 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
1-26
Chapter 1: Product introduction
8.
Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s).
Connect the S/PDIF Out module cable to this connector, then install the module to a
slot opening at the back of the system chassis.
The S/PDIF module is purchased separately.
9.
Marvell
®
Serial ATA 6.0 Gb/s connectors (7-pin SATA_6G_1/2 [gray])
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0
Gb/s signal cables.
•
These connectors are set to Standard IDE mode by default. In Standard IDE mode, you
can connect Serial ATA boot/data hard disk drives to these connectors.
•
You must install Windows
®
XP Service Pack 2 or later versions before using Serial ATA
hard disk drives.
•
When using hot-plug and NCQ, set the
Marvell 9123 Controller
item in the BIOS to
[AHCI Mode]. Refer to section
Onboard Devices Configuration
for details.