Asus P9X79 DELUXE User Manual - Page 104

S.M.A.R.T. Status Check [Enabled] - raid driver

Get Asus P9X79 DELUXE PDF manuals and user guides View all Asus P9X79 DELUXE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

SATA Mode [AHCI Mode] Allows you to set the SATA configuration. [Disabled] [IDE Mode] [AHCI Mode] [RAID Mode] Disables the SATA function. Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Set to [RAID Mode] when you want to create a RAID configuration from the SATA hard disk drives. The following two items appear only when you set the SATA Mode item to [IDE Mode]. Serial-ATA Controller 0 [Enabled] Allows you to enabled/disabled the Serial-ATA Controller 0. Configuration options: [Disabled] [Enabled] [Compatible] Serial-ATA Controller 1 [Enabled] Allows you to enabled/disabled the Serial-ATA Controller 1. Configuration options: [Disabled] [Enabled] S.M.A.R.T. Status Check [Enabled] S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. Configuration options: [Disabled] [Enabled] SATA6G_1 (Gray) Hot Plug [Disabled] This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode]. It's allow user to enabled/disabled SATA Hot Plug Support. �C�o��n�fi�g�u��ra��ti�o�n��o�p��ti�o�n��s�:�[�D�i�s�a�b��le��d�] [Enabled]. SATA6G_2 (Gray) Hot Plug [Disabled] This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode]. It's allow user to enabled/disabled SATA Hot Plug Support. �C�o��n�fi�g�u��ra��ti�o�n��o�p��ti�o�n��s�:�[�D�i�s�a�b��le��d�] [Enabled]. Chapter 3 3-30 Chapter 3: BIOS setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
3-30
Chapter 3: BIOS setup
Chapter 3
SATA Mode [AHCI Mode]
Allows you to set the SATA configuration.
[Disabled]
Disables the SATA function.
[IDE Mode]
Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
[AHCI Mode]
Set to [AHCI Mode] when you want the SATA hard disk drives to use the
AHCI (Advanced Host Controller Interface). The AHCI allows the onboard
storage driver to enable advanced Serial ATA features that increases
storage performance on random workloads by allowing the drive to
internally optimize the order of commands.
[RAID Mode]
Set to [RAID Mode] when you want to create a RAID configuration from the
SATA hard disk drives.
The following two items appear only when you set the
SATA Mode
item to [IDE Mode].
Serial-ATA Controller 0 [Enabled]
Allows you to enabled/disabled the Serial-ATA Controller 0.
Configuration options: [Disabled] [Enabled] [Compatible]
Serial-ATA Controller 1 [Enabled]
Allows you to enabled/disabled the Serial-ATA Controller 1.
Configuration options: [Disabled] [Enabled]
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST.
Configuration options: [Disabled] [Enabled]
SATA6G_1 (Gray)
Hot Plug [Disabled]
This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode].
It’s allow user to enabled/disabled SATA Hot Plug Support. Configuration options: [Disabled]
Configuration options: [Disabled]
[Enabled].
SATA6G_2 (Gray)
Hot Plug [Disabled]
This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode].
It’s allow user to enabled/disabled SATA Hot Plug Support. Configuration options: [Disabled]
Configuration options: [Disabled]
[Enabled].