Asus PUNDIT P1-AH1 User Guide - Page 33

ASUS Pundit P1-PH1 system, Serial ATA - ph1 power supply

Get Asus PUNDIT P1-AH1 PDF manuals and user guides View all Asus PUNDIT P1-AH1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

To install a Serial ATA hard disk drive: 1. Follow steps 1-3 of the previous section. 2. Connect one end of the supplied 7-pin SATA cable to the connector at the back of the Serial ATA cable drive, then connect the other end to the SATA connector on the motherboard. See page 4-7 for the location of the Serial ATA connector. 3. For Serial ATA HDDs with a 4-pin power connector: Connect a 4-pin (female) power plug from the power supply unit (PSU) to the 4-pin (male) power connector at the back of the drive. For Serial ATA HDDs without a 4-pin power connector: Use the supplied SATA power cable. Connect a 4-pin plug (female) from the PSU to the 4-pin (male) plug of the SATA power cable. Connect the 15-pin SATA power plug to the power connector at the back of the drive. 15-pin 4-pin (male) Serial ATA power cable ASUS Pundit P1-PH1 system 2-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
2-17
ASUS Pundit P1-PH1 system
To install a
Serial ATA
hard disk drive:
1.
Follow steps 1-3 of the previous section.
2.
Connect one end of the supplied
7-pin SATA cable to the
connector at the back of the
drive, then connect the other end
to the SATA connector on the motherboard. See page 4-7 for the
location of the Serial ATA connector.
3.
For Serial ATA HDDs
with
a 4-pin power connector:
Connect a 4-pin (female) power plug from the power supply unit
(PSU) to the 4-pin (male) power connector at the back of the drive.
For Serial ATA HDDs
without
a 4-pin power connector:
Use the supplied SATA power
cable. Connect a 4-pin plug
(female) from the PSU to the
4-pin (male) plug of the SATA
power cable. Connect the
15-pin SATA power plug to the
power connector at the back of
the drive.
Serial ATA cable
Serial ATA power cable
4-pin (male)
15-pin